bauhaus ST0520SRW User manual

Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Bauhaus will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modified or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should be only be installed by a suitably qualified
Plumber/installer. Should the installation be completed by a
non-qualified person any product guarantee maybe considered
invalid. For a claim made under our warranty written certification
of your installers qualifications can be required.
It is advised that all doors and drawers are removed prior to fitting
to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
flat to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care at all times.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Handle glass with care. Although the glass supplied is toughened
safety glass (to BS6206), impacts can damage both the glass and
the furniture.
Warning! Please check for any hidden pipes or electrical cables
before drilling holes in the floor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Care & Cleaning
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products
Use a well wrung chamois leather or micro fibre cloth for furniture
carcasses.
Resin wash basins should only be cleaned with a mild detergent
or warm soapy water; in hard water areas a good quality lime-
scale remover can be applied.
Clean mirrors only with a micro fibre cloth.
If any maintenance is required then it must be carried out by a
qualified Plumber.
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed: Drill, 5mm Suitable drill bit, Phillips screwdriver , Spirit level, Ruler/tape measure,Pencil,Silicone
590 Drawer Vanity Unit & Basin
440 Door Vanity Unit & Basin 850 Drawer Vanity Unit & Basin
BATHROOM FURNITURE RANGE STREAM
INSTALLATION INSTRUCTIONS
ST4400
ST0520SRW
ST5900
ST0521SRW
ST8500
ST0522SRW
ST3016
Storage Unit
4.8X38mmx6
4x25mmx2
x2
x1
Including 4 pre-fitted glass shelvesIncluding 1 pre-fitted glass shelf
sealant (clear).
4.8X38mmx6
4x25mmx2
x2
x1
4.8X38mmx6
4x25mmx2
x2
x1
4.8X38mmx6
4x25mmx2
4.8x50mmx2
x2
x1

2
Plan unit position
Decide on the position
and height of the unit. The
recommended basin height is
between 860mm and 870mm.
Mark the fixing positions onto
the wall.
Drill Ø 5mm holes, insert the
wall plugs and fix using 6 of
the large screws.
Place the unit centrally onto the lower bracket. Ensure it is level and mark all 4 fixing positions onto the wall.
Remove the unit, drill Ø 6mm holes and insert the wall plugs.
Remove the drawer before installation. Pull out fully, lift the front,
pull out again, lower and fully remove.
Remove the door before installation. Loosen the screw (shown)
on both hinges, pull the door back and lift the hinges off the hinge
plates. Remove the glass shelf.
Door Unit - 440 Door Vanity Unit only
Step 1
Vanity Unit & Basin Installation - 590 Drawer Vanity Unit is shown as a typical example
Step 2
Step 3
860mm -
870mm
440mm -
450mm
Loosen
840mm -
513mm
850mm
590 Drawer Vanity Unit 850 Drawer Vanity Unit
365mm
440 Drawer Vanity Unit
775mm513mm

3
a: Attach the tap to basin and
carefully bed in the waste
using silicone only.
b: Carefully apply silicone to
the top edges of the unit.
c: Carefully position the basin
down onto the unit, ensure is
centrally positioned and flush
at the back.
Connect the tap and waste.
Attach door handle: Attach the handle
to the door front. Note: Only attach the
handle now if not changing the opening
side (see below).
Re-fit door: Reposition both hinges over
the screws on the hinge plates. Pull the
door forward and tighten the screws.
Re-fit the glass shelf.
Re-fit drawer: Pull out both runners.
1: Place the drawer onto the runners.
2: Push in until the drawer ‘clicks’ into
position.
Door Unit - 440 Door Vanity Unit only
To move door up or down: Loosen
screws shown and move door up or
down to suit. Re-tighten.
To move door in or out: Loosen screw
shown and move door in or out to suit.
Re-tighten.
To move door left or right: Loosen
screw shown and move door left or right
to suit. Re-tighten.
a: Loosen the screw (shown) on both hinges, pull door back
and lift the hinges off the hinge plates. b: Remove the hinge
plates (and soft close mechanism).
c: Re-fit the hinge plates (and soft close mechanism) onto the
opposite side. d: Rotate the door. Reposition both hinges over
the screws on the back plates. Pull door forward and tighten the
screws. Attach the handle to the top set of holes on the door.
Changing door opening side
Hinge adjustment
Step 4
Step 5
Tighten
1
2
‘click’
Loosen Tighten
Remove Re-fit
ad cb
a cb

Storage Unit installation
For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.bauhaus-bathrooms.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
From inside the unit, use
a screwdriver to adjust the
hanging position.
a: To lift or lower the unit adjust
the screw shown.
b: To move the unit closer or
further from the wall adjust the
screw shown. Note: The unit
may need to be removed and
the ‘hanging hooks’ adjusted.
When correctly aligned, fix up
through the lower bracket into
the unit using the small screws.
Note: If door requires
adjustment, follow the hinge
adjustment section on page 3.
Decide on the opening side of the door,
rotate the whole unit to change the
opening side.
Drill Ø 5mm holes, insert the wall plugs and fix using the 6 large screws.
a: Ensure it is vertical and mark
top corner positions onto the wall.
b & c: Remove the unit, mark
the fixing hole positions onto
the wall. Drill Ø 5mm holes,
insert the wall plugs and the
wall brackets.
d: Positions onto the wall,
insert screws.
Step 1
Step 2
Step 3
208
mm
62
mm
770
mm
60
mm
Back
208mm
150mm
60
mm
770
mm
of unit
a
b
ab
d
c
Plan unit position
We suggest positioning the
tower unit so it is level with
any other unit that has been
installed.
Unit height
dependent on
basin height