bauhaus EDGE User manual

Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Bauhaus will not be held responsible for any de-t / re-t costs
where faulty product has been tted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modied or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualied
Plumber/installer. Should the installation be completed by a
non-qualied person any product guarantee maybe considered
invalid. For a claim made under our warranty written certication
of your installers qualications can be required.
It is advised that all doors and drawers are removed prior to tting
to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
at to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care at all times.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Important pre-installation notes
The Console Units are designed for use with wall mounted taps
or countertop basins with a tap ledge.
We strongly recommend that twin basin settings are installed
on a sold wall only.
The console units CAN ONLY BE installed using the tting
brackets supplied.
Warning! Please check for any hidden pipes or electrical cables
before drilling holes in the oor or walls. When using power tools
always follow the manufacturer’s user instructions.
Care & Cleaning
Clean furniture with warm clean water and microbre cloth.
Normal domestic cleaners that have no bleach or abrasive
ingredients can be used to remove stubborn marks. Then wipe
with fresh water, removing all traces of the cleaning agent,
to prevent streaks forming and dry the surface with a clean
microbre cloth.
If any maintenance is required then it must be carried out by a
qualied Plumber.
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed: Drill, 8mm Suitable drill bit, Suitable size hole cutters, Phillips screwdriver, Spirit level,
Ruler/tape measure, Pencil, Silicone sealant (clear).
1200 Single Drawer Console Unit & Concealed Wall Brackets800 Single Drawer Console Unit & Concealed Wall Brackets
BATHROOM FURNITURE RANGE EDGE
INSTALLATION INSTRUCTIONS
x8x8 x4
ED8040D
ED1245D
x8x8 x4

2
800 Single Drawer Console Unit 1200 Single Drawer Console Unit
a
Bracket
height
dependent
on basin
height
Bracket
height
dependent
on basin
height
a
Positioning and Attaching Wall Brackets - Dimensions in Centimeters
Positioning and Attaching Wall Brackets
Place the wall brackets against the wall at the required height
and distance apart (see diagram ‘a’ for dimensions of units and
positions of wall brackets).
Ensure the brackets are level and mark the xing positions onto
the wall.
b: Drill Ø 8mm holes, insert
the wall plugs and x using the
screws.
b
EDGE 800 BASIN/DRAWER
Dimensions in Centimeters
11.5
40
Positioning of Basin Waste Hole - 800 Unit Only - Dimensions in Centimeters
Note: The Console Units are designed for
use with wall mounted tap/s or basins with
a tap ledge.
Basin waste xing position
a: The 800 unit is specially designed to
take a basin in a central position.
Important: ONLY drill/cut holes in the
grey area, ensuring there is sufcient
space front and back.
b: This diagram shows the positions of the
tap and waste holes going into the wall.
c: Prepare Console top for the basin.
Cut hole using a suitable sized hole cutter.
Important: ALL cut edges MUST be
sealed with water proof sealant or exterior
wood varnish.
a
b
c
Step 1
800 & 1200 Single Drawer Console Unit Installation
Step 3
Step 4a
Remove the drawer before installation.
Pull out fully, lift up front and remove.
Step 2
Plan unit position
Decide on the position and
height of the unit.
The recommended basin
height is between 860mm
and 870mm.
Basin
height
860mm -
870mm Bracket height
dependent on
basin height
We strongly recommend Twin Basin formats are installed on a solid wall ONLY
7.8-8.3
7
98
8 8
7
7.8-8.3
7
58
88
7
40
58
31
11.5
8 8
77
58
Hole cutter

3
EDGE 1200 BASIN/DRAWER WASTE AREAS
Dimensions in Centimeters
Single Basin Left Aligned Single Basin Right Aligned
Single Basin Centre Aligned Two Basins
EDGE 1200 BASIN/DRAWER WASTE AREAS
Dimensions in Centimeters
Single Basin Left Aligned Single Basin Right Aligned
Single Basin Centre Aligned Two Basins
EDGE 1200 BASIN/DRAWER WASTE AREAS
Dimensions in Centimeters
Single Basin Left Aligned Single Basin Right Aligned
Single Basin Centre Aligned Two Basins
EDGE 1200 BASIN/DRAWER WASTE AREAS
Dimensions in Centimeters
Single Basin Left Aligned Single Basin Right Aligned
Single Basin Centre Aligned Two Basins
800 Unit is shown as a typical example
a: Place the Console onto the wall
brackets and ensure it is level.
b: To level: Adjust the height of the wall
bracket pads until level.
c: Position the Console down onto the
brackets, check it’s level and x using the
4 shorter screws.
Connect tap/s, basin and waste.
Note: The use of a Crosswater extended
thread basin waste is recommended.
Carefully apply silicone to the join between
the Console and wall and around the base
of the basin.
Leave silicone, 24 hours to dry.
Step 5
Positioning of Basin Waste Hole/s - 1200 Unit Only - Dimensions in Centimeters
Note: The Console Units are designed for
use with wall mounted tap/s or basins with
a tap ledge.
Basin Waste Fixing Position/s
a: The 1200 unit is specially designed to
take one basin centrally aligned, or by
rearranging the drawer ttings to take
basins on the left, right or left and right.
Important: ONLY drill/cut holes in the
grey area/s, ensuring there is sufcient
space front and back.
b: These diagrams show positions of the
tap and waste holes going into the wall.
c: Prepare Console top for the basin.
Cut hole using a suitable sized hole cutter.
Important: ALL cut edges MUST be
sealed with water proof sealant or exterior
wood varnish.
a
b
c
Step 4b
a
b
a
b
a
b
Step 6
a b
c
Single Basin - Left Aligned
Single Basin - Right Aligned
Single Basin - Centre Aligned
Two Basins - For use on solid walls only
60
11
35.5
98
8
5
77
88
34
11
35.5
98
8
5
77
88
34
11
35.5
98
8
5
7 7
88
31
5.5
35.5
98
8
5
77
88
31
5.5
8
5

For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.bauhaus-bathrooms.co.uk
The manufacturer reserves the right to make technical
modications without prior notice.
Step 7
The following steps show how to rearrange the drawers for a two
basin arrangement. For left and right arrangements the procedure
is similar except the middle drawers are moved to the left or right.
a: Remove all hole plugs from drawer back. Loosen all 8 Cam
Nuts shown inside and on the underside of the drawers.
b: Lift and angle both middle drawers up and away from the side
drawers. Note: Wooden Dowels connect the middle and side
drawers.
Rearranging the Drawer Fittings - 1200 Unit Only - Two Basin arrangement shown as example
c: Unscrew and reposition the exposed Cam Bolts to the
positions shown. Note: If unsure which are the correct holes, use
the middle drawers as a template.
d: Insert a Wooden Dowel between the middle drawers and lower
down onto the Cam Bolts.
Re-tighten all 8 Cam Nuts inside and on the underside of the
drawer that were loosened in ‘a’. Push t Hole Plugs into all
unused holes.
Step 8
Re-t drawer
Place the drawer onto the runners and push in fully.
Cam
Nuts
Cam
Bolts
Hole PlugsCam Nuts
a b
d
c
Hole Plugs