bauhaus ZION 50 User manual

Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Bauhaus will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will be
taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modified or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualified
Plumber/installer. Should the installation be completed by a
non-qualified person any product guarantee maybe considered
invalid. For a claim made under our warranty written certification
of your installers qualifications can be required.
It is advised that all doors and drawers are removed prior to fitting
to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
flat to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care at all times.
Please note that some units are heavy.Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Handle glass with care. Although the glass supplied is toughened
safety glass (to BS6206), impacts can damage both the glass and
the furniture.
Warning! Please check for any hidden pipes or electrical cables
before drilling holes in the floor or walls.
When using power tools always follow the manufacturer’s user
Do not over tighten tap or waste fittings, doing so may result in
damaging the basin.
instructions.
Care & Cleaning
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products
Use a well wrung chamois leather or micro fibre cloth for furniture
carcasses.
Ceramic fine fire clay wash basins should only be cleaned with a
mild detergent or warm soapy water; in hard water areas a good
quality limescale remover can be applied.
Clean mirrors only with a micro fibre cloth.
If any maintenance is required then it must be carried out by a
qualified Plumber.
IMPORTANT - Advice and safety -Please read before installation
Tools & equipment needed: Drill, 8mm Suitable drill bit, 3.5mm General drill bit, Suitable size hole cutters, Phillips screwdriver,
Spirit level, Ruler/tape measure, Pencil, Silicone sealant (clear).
500 Single Drawer Basin Unit & Basin
BATHROOMFURNITURE RANGEZION 50 - WALL HUNG
ZION wall hung unit DRAWER 1 May 17
ZI0501SCW
5 KG
ZI4900D
13 KG
Handle Options
ZIHBOW-CP
ZIHSTR-CP
*Sold separately
To ensure full working use of the drawers
we recommend the use of Bauhaus basin
furniture trap BTR0410W
x2
x4

2
Step 1
860mm -
870mm
Unit height
dependent on
basin height
Step 2
Plan unit position
Decide on the position and
height of the unit.
The recommended basin
height is between 860mm
and 870mm.
Single Drawer Basin Unit & Basin Installation
Remove the drawer before installation. Pull the drawer fully
out, lift the front, pull out again, lower and fully remove.
Step 3 425mm
113
mm
ZION wall hung unit DRAWER 2 May 17
‘Wall bracket’ installation
Removing bracket from the wall
Use the measurements above, to position the ‘wall brackets’.
a: Important:The measurements given
above are the maximum the brackets can
EHVSDFHGDSDUWWKHEUDFNHWVPXVW¿W
within that measurement.
b:
Important: ,IWKHEDVLQXQLWDQGRUEDVLQDUHQRW¿WWHGOHYHOWKLV
PD\UHVXOWLQWKHEDVLQQRWGUDLQLQJFRUUHFWOy.
Position the unit on the brackets.
0DUNWKHEUDFNHWIL[LQJKROHVRQWRWKHZDOO
'ULOOPPKROHVLQVHUWWKHZDOOSOXJVVXSSOLHGRQ
VROLGZDOOVXVHVXLWDEOHZDOOIL[LQJVIRUGU\ZDOO
QRWVXSSOLHGDQGDWWDFKWKHEUDFNHWVF
a
c
b
c
113
mm 52
mm
36mm
425mm
Top
INSTALLATION INSTRUCTIONS

3
a: Attach the tap to basin and
carefully bed in the waste
using silicone only.
b: Carefully apply silicone to
the top edges of the unit.
c: Carefully position the basin
down onto the unit, ensure it is
centrally positioned and flush
at the back.
Connect the tap and waste.
Apply a bead of silicone to the
join between the basin/unit and
wall, on all 4 sides.
Leave silicone, 24 hours to dry.
Re-fit drawer: Pull both
drawer runners fully out.
1: Set the drawer down onto
the runners.
2: Push the drawer fully in until
it locks (click).
Test to make sure the drawer
operates correctly.
Step 4
a: Check the unit is level.
If levelling is required, use
a screwdriver to adjust the
hanging position, as follows:
b: To lift or lower the unit,
adjust the screw shown.
c: To move the unit closer or
further from the wall, adjust the
screw shown.
c
a
Step 5
a cb
ZION wall hung unit DRAWER 3 May 17
b
Note: Basin waste and taps fittings when over tightened can
create stress within the basin material which may in time
cause the failure of the product. Waste fittings should be
carefully bedded in silicone and the back nut hang tightened
an additional quarter turn using a suitable spanner is sufficient to
create the required waterlight seal. Care should also be taken
when fitting brassware to tap platforms in order to prevent similar
stress related failures.
Step 6
‘click’
2
1

For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.crosswater.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
ZION wall hung DRAWER 4 May 17