Dream On Me 653 User manual

1
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you
quickly assemble your products. Before you begin we recommend
that you following the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver
Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 653
s
Dream On Me Inc.
1532 S Washington Ave
Piscataway Township
NJ 08854
TEL: [phone]
Customer Care: [phone]

2
WARNING !
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
· READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
· UPON COMPLETION OF ASSEMBLY, MAKE SURE ALL SCREWS,BOLTS AND
FASTENERS HAVE BEEN SECURELY TIGHTENED.
A FREQUENT AND PEDRIODICALLY CHECK SHOULD BE MADE TO CONFIRM ALL
THE SCREWS AND NUTS REMAIN TIGHT.
· NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE, MISSING FASTENERS,
LOOSE JOINTS,BROKEN PARTS, OR TORN MESH/FABRIC.CONTACT DREAM ON ME
1532 S WASHINGTON AVE PISCATAWAY TOWNSHIP, NJ 08854 732-752-7220 FOR
REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED.
· NEVER SUBSTITUTE PARTS, THE PRODUCT INCLUDING SIDE RAILS,MUST BE
FULLY ERECTED PRIOR TO USE.
· NEVER USE BED FOR INFANTS, THIS TODDLER BED IS NOT A SUBSITITUTE FOR A
CRIB,THE TODDLER BED IS USED FOR A CHILD BETWEEN THE AGE OF 15MONTHS
TO 5 YEARS WITH A MAXIMUM WEIGHT OF 50 POUNDS(22.7KG).
· NEVER USE PLASTIC SHIPPING BAGOR OTHER PLASTIC FILM AS A MATTRESS
COVERS NOT SOLD AND INTENDED FOR THAT PURPOSE,THEY CAN CAUSE
SUFFOCATION.
· CAUTION ENTRAPMENT HAZARD:TO AVOID DANGEROUS GAPS,ANY MATTRESS
USED IN THIS BED SHALL BE FULL SIZE CRIB MATTRESS AT LEAST 51-58IN
(1310MM) IN LENGTH, 27-1/4IN(690MM) IN WIDTH AND 4IN(100M) IN THICKNESS,OR
GREATER,BUT NOT EXCEED 5IN.
· NEVER USE A WATER MATTRESS WITH THIS TODDLER BED.
· WARNING STRANGULATION HAZARD:STRINGS CAN CAUSE STRANGULATION!
NEVER PLACE BED NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.NEVER SUSPEND STRINGS OVER BED.
NEVER PLACE ITEMS WITH A STRING CORD,OR RIBBON,SUCH AS HOOD STRINGS,
PACIFIER CORDS AOUND A CHILS’S NECK.THESES ITEMS MAY CATCH ON BED
PARTS.
· WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
OPENINGS IN AND BETWEEN BED PARTS CAN ENTRAP HEAD AND NECK OF A
SMALL CHILD. NEVER USE BED WITH CHILDREN UNDER 15MONTHS.ALWAYS
FOLLOW THE ASSEMBLY INSTRUCTIONS.
· TO REDUCE THE RISK OF SIDS,PEDIASTRICIANS RECOMMED HEALTHY INFANTS
BE PLACED ON THEIRE BACK TO SLEEP,OR ADVISED BY YOUR PHYSICIAN.
· DO NOT USE BED IF THE SPACE BETWEEN BED AND SOLID OBJECTS IS LESS
THAN 12IN(31CM), A CHILD COULD SLID INTO THE SPACE AND SUFFOCATE.
· IF REFINISHING,USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
TO WASH,CLEAN WITH MILD SOAP AND DAMP CLOTH.
TO STORE,PLEASE KEEP IN A COOL PLACE.
MADE IN CHINA

3
COMPONENT PARTS
(A) Headboard (1pc) (B) Footboard (1pc) (C) Back Rail (1pc)
(D)Left Leg (1pc)
(E) Right Leg(1pc)
(K) Drawer Front Panel (1pc)
(J) Cross Bar (8pcs)
(M) Drawer Back Panel
(1pc)
(I) Drawer Bottom panel
(2pcs)
(N) Drawer Middle Panel
(1pc)
(O) Drawer Bottom Support
(1pc)
(F) Bed Rail (1pc)
L2
L1
(L2) Drawer Right panel(1pc)
DE
(G) Side Bar (1pc)
(H) Cross Middle Bar (1pc)
(L1) Drawer Left panel(1pc)

4
STEP 1
HARDWARE AND TOOL DIAGRAM
(a) Bolt 3’ (5pcs) (b) Bolt 2-1/5’ (14pcs) (c) Barrel nut (19pcs)
(d) Allen Wrench (1pc) (e) Bolt 1-3/5’ (2pcs) (f) Wood Dowel (6pcs)
(i) Wood Screw (1pc)
PHILLIPS-HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ---- NOT INCLUDE
Connect the side bar (G) to the left leg
(D) and the right leg (E) using barrel nuts
(c) and bolts (a).Make sure that the
hole on the side bar(G) are facing up,
and nearer the left leg(D).
a
a
c
c
D
E
G
(g) Cam Bolt (12pcs) (h) Cams (12pcs)

5
STEP 2
STEP 3
Connect the headboard (A) and the
footboard (B) to the back rail (C) using
barrel nuts (c) , bolts (b) and wood
dowels (f) .
Connect Cross middle bar (H) to the back
rail (C) using barrel nut (c) and bolt (b).
Attach cross bar (J) to the back rail (C).
Please note: the cross end should fit into
hole.
f
f
b
b
b
b
c
c
c
C
A
B
c
b
H
JJJJ
JJJJ
C

6
STEP 4
STEP 5
Connect Cross middle bar (H) to the side
bar (G) using barrel nut (c) and bolt (b).
Attach cross bar (J) to the side rail (G).
Please note: cross bar end should fit into
hole.
Then connect the headboard (A) to the
left leg (D) and connect the footboard
(B) to the right leg (E) using barrel nuts (c)
bolts(b) and wood dowels (f) .
Connect the bed rail (F) to the left leg
(D) using the barrel nut (c) and the bolt
(a) and bolt (e).Then connect the bed
rail (F) to the side bar (G) using the bolt
(e) as shown.
ac
b
c
b
b
b
b
b
b
f
f
c
c
c
c
H
G
JJJJ
J
A
D
B
E
e
e
G
F
D

7
Attach the Middle Panel (N) to the
center of the Drawer Back Panel
(M) using 1pc Wood Dowel (c) , 1pc
Cam Bolt (g) and 1pc Cam (h) .
Attach the Bottom Support Bar (O)
to the center of the Drawer Back
Panel (M) using 1pc Cam Bolt (g)
and 1pc Cam (h) .
STEP 7
Attach both Drawer Right Side (L2)
and Drawer Left Side (L1) to the
Drawer Back Panel (M) by inserting
4pcs Cam Bolts (g) to the end holes
of the Drawer Side Panel (L1&L2) as
shown . Make sure the grooves
line up and face inside.Insert 4pcs
Cams (h) into the holes of Drawer
Back Panel (M) . Lock the Cams (h)
in the Drawer Back Panel (M) using
phillips-head screwdriver .
STEP 6
M
L2
L1 g
h
h
h
hg
f
M
ON

8
Attach Drawer Front Panel (K) by
inserting Cam Bolts (g) into their
corresponding Cam Bolts holes on
ends of Drawer Side Panel (L1&L2),
the Bottom Support Bar (O) and the
Middle Panel (J) . Make sure the
Drawer Bottom Panels (I) are also
inserted into grooves of Drawer
Front Panel (K) . Lock Cams (h) by
turning them clockwise .
Place the whole drawer flat on the
floor with the back up . Screw the
screw (i) from the middle of the
Bottom Support Bar (O) to the
Middle Panel (N) , as the image
shown .
STEP 9
Slide Drawer Bottom Panels (I)
painted side up , into grooves of
Drawer Side Panel (L1&L2) , the
Bottom Support Bar (O) and the
Middle Panel (N) as shown .
STEP 8
I
I
O
N
L2
L1
K
O
I
I
L2
L1
g
g
g
h
h
h
i
h

9
Congratulations , your toddler bed with drawer is ready to use .
STEP 11
Line up the drawer with the
wheels and mental tracks on
each side .
With the front slightly elevated ,
slide into the track on the end ,
lowering the front as it rolls into
place under the toddler bed .
STEP 10