bauhaus 300 Double Drawer Unit User manual

Please read these instructions carefully before starting installation
and keep in a safe place for future reference. ENSURE the room is
well heated and ventilated.
Check the contents of the pack carefully before installation. Bauhaus will
not be held responsible for any de-t / re-t costs where faulty product
has been tted.
If any fault is found with materials or workmanship, it must be reported
immediately to the manufacturer. Remedial action will be taken, based
on information received, on condition that: 1. Full details are supplied
to the manufacturer; 2. The product has not been modied or tampered
with; 3. The manufacturer is informed of any damage/shortages prior to
installation. 4. The product has not been installed, or attempts have been
made to install.
We do not accept responsibility for any problems that may occur through
incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualied Plumber/
installer. Should the installation be completed by a non-qualied person
any product guarantee maybe considered invalid. For a claim made under
our warranty written certication of your installers qualications can be
required.
It is advised that all doors and drawers are removed prior to tting to avoid
unnecessary damage occurring.
It is recommended that the furniture and accessories are installed after
tiling, ensuring that the product is installed at to the tile face and allows
product to be easily removed if required in the future.
These hints have been prepared for your guidance, you must exercise
due care at all times.
Please note that some units are heavy. Always take care when lifting, and
follow health and safety guidelines. It is recommended that 2 people carry
out the installation of larger basin/vanity units.
Warning! Please check for any hidden pipes or electrical cables before
drilling holes in the oor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Always use the correct wall xings for non-solid walls – not supplied.
Important pre-installation notes
The carcass on coloured products is supplied with a protective lm. This
should be removed only after installation is complete. Simply peel off and
wipe down with a well wrung chamois leather or micro bre cloth.
To ensure full working use of the drawers we recommend the use of
Bauhaus basin furniture trap BTR0410W.
Care & Cleaning
Ceramic products should be cleaned regularly with warm soapy water,
then rinsed with clean water and, if desired, dried and polished with a soft
cloth. Limescale deposits can be removed using a 50:50 solution of warm
water and limescale remover and soft clean cloth.
We advise against the practice of leaving strong cleaners or bleach in
ceramic products overnight this will permanently damage the glazed
surface.
Use a well wrung chamois leather or micro bre cloth to clean furniture
carcasses.
If any maintenance is required then it must be carried out by a qualied
Plumber.
The manufacturer reserves the right to make technical modications
without prior notice.
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed: Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure, Pencil,
Silicone sealant (clear).
BATHROOM FURNITURE RANGE ESSENCE
INSTALLATION INSTRUCTIONS
ES300 ES5000F
Including 1 pre-fitted adjustable shelf
ES5000D
ES300
300 Double Drawer Unit 500 Double Drawer Unit 300 Single Door Unit 500 Single Door Unit
Including 1 pre-fitted adjustable shelf
x2
x4
x2
x1
x2
x4
x2
x1
x2
x4
x2
x1
x2
x4
x2
x1

2
Remove the drawers before installation.
Push the top drawer to open. Pull the
bottom drawer front to open.
Pull out fully, lift the front, pull out again,
lower and fully remove.
Step 1 Step 2
Door Unit only
Remove the door before installation.
a: Lift the tab (shown) on all hinges,
to release. b: Pull door back.
Step 4
The Essence range of bathroom furniture has
been designed to be installed in either a run of
several units or as individual units.
Note: When installing, the basin unit and basin
should be tted rst. Typical example of a run of units
Basin &
Basin
Unit
Double
Drawer
Unit
Single Door
Unit
a
b
Step 3
Plan unit position
We suggest positioning the storage units
so they are level with any other units that
have been installed.
Option 1: ‘Hanging hooks’
Use the measurements above, to position the ‘hanging hooks’.
a: Mark the xing hole positions onto the wall.
Drill Ø 8mm holes, insert the wall plugs and the ‘hanging hooks’.
b: The ‘hanging hooks’ should protrude from the wall by 5-7mm.
Position the unit on the hanging hooks.
300 Double Drawer Unit/Single Door Unit
230mm
175
mm
175
mm
430mm
500 Double Drawer Unit/Single Door Unit
Note: The Units can be hung using one of two options, ‘Hanging hooks’ or ‘Wall brackets’ depending on your
requirements and wall structure. It is recommended to use the bracket option on non-solid walls.
175
mm
a
5-7mm
b
Drawer/Door Unit Installation - 500 Double Drawer Unit is shown as a typical example
Push to open
380mm -
390mm

3
Re-t drawers:
a: Pull out both lower drawer runners.
1: Place the lower drawer onto the
runners.
2: Push in until the drawer ‘clicks’ into
position.
b: Repeat with top drawer.
Step 6
Single Door Units
Note: only attach the handle
now if not changing the
opening side (see next page).
Attach handle: Attach the
handle to the door front.
Double Drawer Units
Attach handle: Attach the
handle to the door front. Note: Only re-t door now if not changing the opening side
(see next page).
Re-t door: a: Reposition both hinges onto the hinge plates.
b: Push the front until the hinge ‘clicks’ into position.
ba
Step 7
Option 2: ‘Wall brackets’
Use the measurement above, to position the ‘wall brackets’.
a: Important: The measurement given
above is the maximum the brackets can
be spaced apart, the brackets must t
within that measurement.
b: Mark the bracket xing holes onto the
wall. Drill Ø 8mm holes, insert the wall
plugs and attach the brackets.
c: Important: The brackets must be the
correct way up, as shown.
Position the unit on the brackets.
acTop
b
175
mm
Step 5
a: Check the unit is level.
If leveling is required: inside
the unit, use a screwdriver to
adjust the hanging position.
b: To lift or lower the unit
adjust the screw shown.
c: To move the unit closer or
further from the wall adjust the
screw shown.
bc
a
Step 8
1
2
‘click’
1
2
‘click’
a b

For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.bauhaus-bathrooms.co.uk
The manufacturer reserves the right to make technical
modications without prior notice.
To move door up or down: Turn screw
shown to move door up or down to suit.
To move door in or out: Turn screw
shown to move door in or out to suit.
To move door left or right: Turn screw
shown to move door left or right to suit.
a: Lift tab (shown) on both hinges, to release the hinges.
b: Pull door back. c: Lift the hinge plate tabs. d: Remove the
hinge plates.
e: Re-t both hinge plates on the opposite side. f: Fold hinge
plate tabs back. g: Rotate door. Reposition both hinges onto
the back plates. h: Push the front until the hinge ‘clicks’ into
position. Attach the handle to the top set of holes on the door.
If changing the door opening side or the door alignment needs adjusting, follow the
instructions below.
Changing door opening side
Hinge adjustment
a b
cd
Remove
e f
Re-t
gh