bauhaus 600 Series User manual

Please read these instructions carefully before starting installation
and keep in a safe place for future reference. ENSURE the room is
well heated and ventilated.
Check the contents of the pack carefully before installation. Bauhaus will
not be held responsible for any de-t / re-t costs where faulty product
has been tted.
If any fault is found with materials or workmanship, it must be reported
immediately to the manufacturer. Remedial action will be taken, based
on information received, on condition that: 1. Full details are supplied
to the manufacturer; 2. The product has not been modied or tampered
with; 3. The manufacturer is informed of any damage/shortages prior to
installation. 4. The product has not been installed, or attempts have been
made to install.
We do not accept responsibility for any problems that may occur through
incorrect installation.
Advice & Safety
This product should be only be installed by a suitably qualied Plumber/
installer. Should the installation be completed by a non-qualied person
any product guarantee maybe considered invalid. For a claim made under
our warranty written certication of your installers qualications can be
required.
It is advised that all doors and drawers are removed prior to tting to avoid
unnecessary damage occurring.
It is recommended that the furniture and accessories are installed after
tiling, ensuring that the product is installed at to the tile face and allows
product to be easily removed if required in the future.
These hints have been prepared for your guidance, you must exercise
due care at all times.
Please note that some units are heavy. Always take care when lifting, and
follow health and safety guidelines. It is recommended that 2 people carry
out the installation of larger basin/vanity units.
Warning! Please check for any hidden pipes or electrical cables before
drilling holes in the oor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Always use the correct wall xings for non-solid walls – not supplied.
Important pre-installation notes
The carcass on coloured products is supplied with a protective lm. This
should be removed only after installation is complete. Simply peel off and
wipe down with a well wrung chamois leather or micro bre cloth.
To ensure full working use of the drawers we recommend the use of
Bauhaus basin furniture trap BTR0410W.
Care & Cleaning
Ceramic products should be cleaned regularly with warm soapy water,
then rinsed with clean water and, if desired, dried and polished with a soft
cloth. Limescale deposits can be removed using a 50:50 solution of warm
water and limescale remover and soft clean cloth.
We advise against the practice of leaving strong cleaners or bleach in
ceramic products overnight this will permanently damage the glazed
surface.
Use a well wrung chamois leather or micro bre cloth to clean furniture
carcasses.
If any maintenance is required then it must be carried out by a qualied
Plumber.
The manufacturer reserves the right to make technical modications
without prior notice.
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed: Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure, Pencil,
Silicone sealant (clear).
BATHROOM FURNITURE RANGE GLIDE
INSTALLATION INSTRUCTIONS
GL1000 GL3590F
Including 1 pre-fitted shelf and
2 adjustable shelves
GL0002SCW
GL8000
GL0001SCW
GL6000
600 Double Drawer Basin Unit
& Basin
800 Double Drawer Basin Unit
& Basin
1000 Double Drawer Basin Unit
& Basin Tower Storage Unit
x2
x4
x2
x4
x2
x4
GL0003SCW
x2
x4

2
Remove the drawers before installation. Pull the drawer fronts to
open the drawers. Pull out fully, lift the front, pull out again, lower
and fully remove.
Step 1 Step 2
Plan unit position
Decide on the position and
height of the unit.
The recommended basin
height is between 860mm
and 870mm.
Step 3
600 Double Drawer Basin Unit 100 Double Drawer Basin Unit
500mm 900mm
860mm -
870mm
360mm -
370mm
100
mm
100
mm
100
mm
700mm
800 Double Drawer Basin Unit
Double Drawer Basin Units Only
Use the measurements above, to position the ‘wall brackets’.
a: Important: The measurements given
above are the maximum the brackets can
be spaced apart, the brackets must t
within that measurement.
b: Mark the bracket xing holes onto the
wall. Drill Ø 8mm holes, insert the wall
plugs and attach the brackets.
c: Important: The brackets must be the
correct way up, as shown.
Position the unit on the brackets.
Important: If the basin unit and/or basin are not tted level this
may result in the basin not draining correctly.
a
cTop
b
100
mm
45mm
455mm
Step 4
a: Check the unit is level.
If leveling is required: inside
the unit, use a screwdriver to
adjust the hanging position.
b: To lift or lower the unit
adjust the screw shown.
c: To move the unit closer or
further from the wall adjust the
screw shown.
bc
a
Basin Unit & Basin Installation - 600 Double Drawer Basin Unit is shown as a typical example

3
a: Attach the tap to basin and
carefully bed in the waste
using silicone only.
b: Carefully apply silicone to
the top edges of the unit.
c: Carefully position the basin
down onto the unit, ensure it is
centrally positioned and ush
at the back.
Connect the tap and waste.
Leave the silicone to dry for
24 hours.
Re-t drawers:
a: Pull out both lower drawer runners.
1: Place the lower drawer onto the
runners.
2: Push in until the drawer ‘clicks’ into
position.
b: Repeat with top drawer.
Tower Storage Unit Installation
Step 1
360mm -
370mm
The storage unit is designed to offer
universal left/right hand door opening
without removal of hinges.
a: Decide on the opening side of the
door. Rotate the whole unit to change the
opening side.
b: We suggest positioning the tower
storage unit so it is level with any other
units that have been installed.
Step 2
240mm
50
mm
Back of unit
a
a: Use the measurements opposite, to
position the ‘wall brackets’.
b: Important: The
measurements given
are the maximum
the brackets can
be spaced apart,
the brackets must
t within that
measurement.
c: Mark the bracket xing holes onto the
wall. Drill Ø 8mm holes, insert the wall
plugs and attach the brackets.
d: Important: The brackets must be the
correct way up, as shown.
Position the unit on the brackets.
50
mm
c
dTop
b
a b
Note: Basin waste and tap ttings when over tightened can create
stress within the ceramic material which may in time cause the failure
of the product. Waste ttings should be carefully bedded in silicone and
the back nut hand tightened an additional quarter turn using a suitable
spanner is sufcient to create the required watertight seal. Care should
also be taken when tting brassware to tap platforms in order to prevent
similar stress related failures.
Step 5
Step 6
1
2
‘click’
acb
1
2
‘click’
a b

For any further information please contact
Bauhaus on: 0845 873 8840
Or visit our web-site at:
www.bauhaus-bathrooms.co.uk
The manufacturer reserves the right to make technical
modications without prior notice.
To move door up or down: Loosen
screws shown and move door up or
down to suit. Re-tighten.
To move door in or out: Loosen screw
shown and move door in or out to suit.
Re-tighten.
To move door left or right: Loosen
screw shown and move door left or right
to suit. Re-tighten.
Step 3
Check the unit is level. If leveling is required: inside the unit, use
a screwdriver to adjust the hanging position.
a: To lift or lower the unit adjust the screw shown.
b: To move the unit closer or further from the wall adjust the
screw shown.
ab
If the alignment of the door needs adjusting, follow the instructions below.
Important information
All ceramic sanitary ware is subject to the limitations of the
manufacturing process. Unlike machine nished products, natural
clay based products shrink and move during high temperature
ring and, because it is not possible to control this process
absolutely, minor variations in the dimensional tolerance, form
and surface of the nished products will occur.
Before installing a wooden bathroom into a new property,
extension or recently plastered room we strongly advise the
building/room is completely dry, well ventilated and adequately
heated.
Hinge adjustment