Baumatic BT10.3BGL User manual

waeady
BT10.3GL/BT10.3BGL
100 cm Glass
chimney hood

User Manual for your Baumatic
BT10.3GL/BT10.3BGL
Cooker Hood
100 cm Glass chimney hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 07/08/07
2

3
Contents Page
Environmentalnote 4
MPORTANT SAFETY INFORMATION 5 – 7
pecifications of your cooker hood 8
sing your Baumatic cooker hood 8 - 9
leaning your Baumatic cooker hood 10
aintenance 11
nstallation 14
15
xtraction mode or recirculation mode? 22
roubleshooting 23 - 24
ontactdetails 25
I
S
U
C
The grease filter 10
M
Removing and cleaning the grease filter 11
Changingalightbulb 12
Fitting the carbon filters 13
I
Electrical connection 14 –
Before beginning installation 15 – 16
Installing your cooker hood 16 – 18
Connecting to external ducting 19
Fitting the chimney section 19 – 21
Completing the installation 22
E
T
C

4
NVIRONMENTAL NOTEE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE

5
MPORTANT SAFETY INFORMATIONI
y is of the utmost importance to Baumatic.
et
n
MPORTANT: Any installation work must be
The hood must be installed in accordance with the installation
If the cooker hood is installed for use above a gas appliance then
tish
It is dangerous to alter the specifications or to modify this
ify
When installing the hood, ensure that the following
ighest point
¾Electric cookers: 700 mm
rs:
IMPORTANT: DO NOT
Your safet
Please make sure that you read this instruction bookl
before attempting to install or use the appliance. If
you are unsure of any of the information contained i
this booklet, please contact the Baumatic Technical
Department.
I
carried out by a qualified electrician or
competent person.
o
instructions and all measurements followed.
o
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scot
Development Department.
o
product in any way. Do not tamper with or attempt to mod
the appliance in any way.
o
recommended distances are observed between the h
on the hob top (including the burners) and the bottom of the
cooker hood:
¾Gas cookers: 700 mm
¾Coal/ oil cooke 800 mm
SET YOUR COOKER HOOD LESS
oWhen installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
THAN 700mm ABOVE YOUR COOKER.

6
s
pecially during installation and
!
o
burning appliance such as a central heating boiler then its flue
oensure that there is
an adequate supply of air in the room.
oon mode, ensure that the
ducting is fire retardant and that there are no bends greater
o
diameter as the outlet hole all the way through.
o
or tampering with the cooker hood. Older
d.
oYour cooker hood is for domestic use only.
Please dispose of the packing material carefully – children are
especially vulnerable to it.
ofire risk.
oAlways put lids on pots and pans when cooking
on a gas cooker.
The manufacturer refuses to accept any responsibility for
damages arising to the hood or for it catching on fire, from a
oThe edges of the cooker hood are sharp – be mindful of this a
you handle your appliance, es
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS
If the room where the cooker hood is to be used contains a fuel
must be of the sealed or balanced flue type.
If other types of flue or appliances are fitted,
When the hood is being used in extracti
than 90 degrees as this will reduce the efficiency of the hood.
Ensure the ducting for the extractor mode has the same
Keep young children from using, playing with
children and infirm persons should be
supervised if they are using the cooker hoo
o
Dirty oil is an even greater
o
failure to observe the fire safety advice contained in these
instructions.

7
ois
rom your room. Ensure that proper ventilation
ooves odours from your
kitchen, not steam.
osure that the cooker
hood has been disconnected from the
k
ong system of this appliance to a
existing ventilation system being used for any other purpose.
o
as overheated fats and oils might catch fire.
oThe cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
oattempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
oer hood.
sed during operation
of the cooker hood. They should not be left on permanently and
HE MANUFACTURER DECLINES ALL
ESPONSIBILITY IN THE EVENT OF FAILURE TO
HERE, FOR
Remember that when in extraction mode, your cooker hood
removing air f
measures are being observed.
Note that the cooker hood rem
Warning - Always en
power supply before carrying out any wor
on the hood, including cleaning and
replacing light bulbs.
Do not connect the ducti n
Do not install above a cooker with a high level grill.
oNever leave frying pans unattended during use
gas burner or heat from electric hob zones without a pan on
them.
Do not
if the filter is excessively greasy!
Never flambé cook under this cook
oThe lights on this appliance should only be u
used as a lighting source.
T
R
OBSERVE THE INSTRUCTIONS GIVEN
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.

8
pecifications of your cooker hoodS
Congratulations on purchasing a Baumatic Cooker
ood!
IONS:
): 1000 mm
Depth (canopy): 500 mm
3 mm
l Cooker Hood is fitted with:
Push button control
rs
lights
H
DIMENS
Width (canopy
Height (with chimney) 593 mm – 109
DIMENSIONS OF CHIMNEY SECTION:
308 mm x 275 mm
Your stainless stee
oHigh extraction tangential motor
o
3 Speeds
o
2 Metallic grease filte
o
2 Halogen
o
Extraction capacity:
o500 m³/hr
ax:
oNoise level min/m 54 – 64 dB
oOptional Extra: 1 x S1 pair of carbon filters
ulation mode
Using y
for air recirc
(available from the Baumatic
SparesDepartment).
our Baumatic cooker hood
Before first use
RTANT: THIS PROCESS MUSTIMPO BE FOLLOWED
EFORE THE COOKER HOOD IS USED FOR THE FIRST
You should use a good quality stainless steel cleaner on ALL of
the stainless steel areas of your cooker hood, before it is used
ove a silicone water-resistant film to protect
the stainless steel surfaces.
B
TIME.
o
for the first time.
This will help to lea

9
To
o
installation instructions.
oof the
functions.
= Low speed
= Medium speed
= High speed
B = Light on/off button
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
use your cooker hood
Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
Find the control panel, which is located at the front right
canopy.
oThere are several buttons on the control panel, which perform
separate
oA = Speed selection buttons
o
HOOD TEN MINUTES
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.

10
leaning your Baumatic cooker hoodC
IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE
R COOKER HOOD
OFF
THAT YOU HAVE SWITCHED YOU
AT THE OMNI-POLAR SWITCH, SET AT THE
oClean the external parts of your cooker hood with mild liquid
gent and a new damp cloth.
Never insert pointed objects into the motor’s protective grid.
oOnly clean the control panel and grease filter grill with mild liquid
the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
o
oIMPORTANT: You should regularly use a good quality
h on
the stainless steel areas of your cooker hood.
o
ondition for
the life of the product.
The
WALL FROM THE CABLE.
Cleaning
deter
oNever use abrasive powder, corrosive solvents or brushes.
o
detergents and a new damp cloth.
oIf you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at
could cause a fire hazard.
Never attempt to clean the area above the grease filters.
stainless steel cleaner to maintain the shine and finis
This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces and keep them in good c
grease filters
o
grease particles to
Your cooker hood includes grease filters which help to absorb
protect your kitchen & furniture from greasy
residues.
o
with this greasy residue.
ould be done every 10-15
days or at least once a month, using hot water and normal
oDO NOT WASH THE GREASE FILTERS IN A DISHWASHER.
The metallic filters may become flammable if they become
saturated
oTo prevent this fire hazard, the filters should be cleaned
regularly. Depending on use, this sh
washing-up detergent.

11
Maintenance
Re o
oFirst remove the grease filter by
handle, and
then pull it upwards away from
the main body of the cooker hood.
ers in hot
about an hour.
oRepeat the process if required.
ers once they have dried.
se filters dry thoroughly before
refitting them in the cooker hood.
m ving and cleaning the grease filters
pulling down on the
oSoak the grease filt water and washing up liquid for
oRinse it off thoroughly with hot water.
oRefit the grease filt
oIMPORTANT: Let the grea

12
Ch
T ENSURE THAT YOU
ISCONNECTED THE COOKER HOOD FROM
UPPLY.
on page 11).
bs ensure that they have cooled
oFind the bulb that requires replacement, you will find it located in
.
oUse a screwdriver to remove the glass cover that sits over the
bulb. Unscrew the light bulb that needs to be replaced and insert
a new G4 20W (max) bulb. Then replace the glass cover.
ofitted
properly into their housings before you call for technical
oRefit the grease filters.
anging a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUS
HAVE D
YOUR MAINS S
oRemove the grease filters (as
described
oPrior to touching the light bul
down.
the light fixture which is inside the exposed section of the
canopy
oIMPORTANT: Defective bulbs should be replaced immediately.
If the lights still do not work, make sure that the bulbs are
assistance.

F
13
itting the carbon filter
t e appliance is going to be used in recirculation mode then it is
ecessary to fit carbon filters. This will help to absorb unpleasant
HAT YOU HAVE DISCONNECTED THE
) Remove the grease filters.
) Hook the carbon filter over
e pins that are located at the
nd of the motor.
) Turn the carbon filter anticlockwise, until you feel
click into place.
oRepeat this process for the second carbon filter. You need to
place a carbon filter at either end of the motor.
oRefit the grease filters.
omonths, or if
they show signs of damage.
If h
n
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE T
COOKER HOOD FROM YOUR MAINS SUPPLY.
1
2
th
e
3
it
The carbon filters should be replaced every three

14
nstallationI
ore installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
.
The manufacturer de lines all responsibility in the event of the installer
iling to observe all the accident prevention regulations in force,
hich are necessary for normal use and the regular operation of the
lectric system.
HOOD IS INTENDED FOR FITTED AND
ERMANENT INSTALLATION.
an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WA
should
fixed wiring via a double pole switched fused spur outlet.
IMPORTANT: Bef
voltage and frequency in your home. The rating
plate can be found behind the grease filters
c
fa
w
e
Electrical connection
YOUR COOKER
P
oThe cooker hood’s power cable must be fitted upstrea
electrical connection, using
m from the
RNING: THIS APPLIANCE MUST BE EARTHED. It
only be connected by a competent person, using
UK ONLY).
lifie
ill comply
and local regulations. The wires in the mains lead are
oloured in accordance with the following UK code:
lue and brown),
en neither must be connected to the earth terminal.
(
We recommend that the appliance is connected by a qua
electrician, who is a member of the N.I.C.E.I.C. and who w
with the I.E.E.
d
c
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (b
th

15
onot
correspond with the coloured markings identifying the terminals
e
nst a
oCheck that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
at will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
he
o
oEnsure that all electrical connections are carried out by a suitably
oBefore commencing installation of the cooker hood the grease
oCheck inside the product and ensure that there is no transit
ld be removed and kept for future
use.
ors
d
. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will
o
As the colours of the wires in the appliance’s mains lead may
in your spur box, please proceed as follows:
oThe blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
oThe brown wire must be connected to th
terminal marked “L” (live), or coloured red.
Before beginning i all tion
electrical socket available th
then there should also be space to connect a ducting hose to t
outside.
Carry out all necessary masonry work prior to the fitting of the
cooker hood.
qualified person.
filters should be removed.
packaging or any other materials, such as packets of screws,
guarantees etc. These shou
If possible, disconnect and move freestanding or slot-in cooke
from their position, to provide easier access to the rear wall an
ceiling
help to protect these surfaces from damage and debris.
Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts and fittings on it.

16
oRawl plugs are provided to secure the hood to most types of
walls and ceilings. However a qualified technician must verify the
suitability of the materials, in accordance with the type of wall
e
o
e surface mounted only.
Ins a
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
oWe recommend that at least two people install this hood.
IM
and ceiling. The wall and ceiling must be strong enough to tak
the weight of the hood.
Do not tile, grout or silicone this appliance to the wall. This
appliance is designed to b
t lling your cooker hood
INSTALLING YOUR
MODE. PLEASE TURN TO PAGE 22 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
PORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filters.

17
)
stall it on and mark the position of the support holes that are
be drilled (as shown in the figure below).
a) The support screw holes are indicated by figure Ain this drawing
nd the anchoring screw holes are indicated by figure B.
3) Using a drill bit with an 8 mm
iameter, make holes in the wall on the
ositions that you have marked in step
2 Position the hood against the wall that you are intending to
in
to
2
a
d
p
2.

18
the holes that you have drilled.
5) Fasten the support screws halfway in, leaving them 10 mm out of
) Hang the hood onto the support
crews.
7) Fully tighten the support screws (A) and then screw the anchoring
screws (B) through the relevant holes in the cooker hood. Tighten the
anchoring screws fully into the wall.
4) Insert rawl plugs into all of
the wall.
6
s

19
Connecting to external ducting
8) Connect the coupling to the top of the cooker hood, and then
connect a 125 mm ducting hose to the coupling (please note that
se should be connected to a
le for cooking vapours. It should
have a cross section of at least 150 cm².
ood.
s of chimney section C
the ducting hose is not supplied with the appliance).
oThe other end of the ducting ho
discharge outlet that is suitab
oThe maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend.
Fitting the chimney
9) Take the two chimney
sections (C and D).
oRest the bottom of
chimney section Con the
top of the hood. You
should take care to
position the tabs on the
chimney section into the
rear of the h
oMark the side
measurement of both
side
on the wall with a pencil.

20
10) Lift chimney section D upwards until it reaches the ceiling. You
must ensure that it is perpendicular to the hood.
oMark the side measurements of both sides of chimney section D
on the wall with a pencil and then remove chimney section D.
11
ma s
oKeeping the bracket in contact with the wall, use a pencil to
mark on the wall the anchoring holes that are cut out of the
bracket
) Take the fixing bracket (E) and place it between the two pencil
rk that you made in step 9.