Baumatic BTC6750GL User manual

BTC6750GL/
BTC9750GL
Cooker Hood

User Manual for your Baumatic
BTC6750GL/BTC9750GL
Cooker Hood
60 cm Cooker hood with LCD display
90 cm Cooker hood with LCD display
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 04/08/10
2

3
Contents Page
Environmentalnote 4
IMPORTANT SAFETY INFORMATION 5 – 7
Specifications of your BTC6750GL cooker hood 8
Specifications of your BTC9750GL cooker hood 9
Using your Baumatic cooker hood 10 - 11
Beforefirstuse 10
To use your cooker hood 10 – 11
Settingthetimeofday 11
Thetimer 11
Cleaning your Baumatic cooker hood 12
Cleaning 12
The grease filter 12
Maintenance 13 - 15
Removing and cleaning the grease filter 13
Changingalightbulb 14
Fitting the carbon filters 15
Installation 16 - 25
Electrical connection 16 - 17
Before beginning installation 17 - 18
Installing your cooker hood 18 – 20
Connecting to external ducting 21
Fitting the chimney 21 – 23
Attaching the glass canopy (BTC9750GL only) 24
Completing the installation 25
Extraction mode or recirculation mode? 25
Troubleshooting 26 - 27
Contactdetails 28

ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4

IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Technical
Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
oThe hood must be installed in accordance with the installation
instructions and all measurements followed.
oIf the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
oIt is dangerous to alter the specifications or to modify this
product. Do not tamper with it or attempt to modify the
appliance in any way.
oWhen installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
¾Electric cookers: 700 mm
¾Gas cookers: 700 mm
¾Coal/ oil cookers: 800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
oWhen installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5

oThe edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
oIf the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
oIf other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
oWhen the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
oEnsure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
oKeep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
oYour cooker hood is for domestic use only.
oPlease dispose of the packing material carefully – children are
especially vulnerable to it.
oDirty oil is an even greater fire risk.
oAlways put lids on pots and pans when cooking
on a gas cooker.
oThe manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
6

oRemember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
oNote that it removes odours from your room, not steam.
oWarning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including replacing light bulbs.
oDo not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
oDo not install above a cooker with a high level grill.
oNever leave frying pans unattended during use
as overheated fats and oils might catch fire.
oDo not leave naked flames under the cooker
hood.
oDo not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
oNever flambé cook under this cooker hood.
oThe lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
oThe cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. a naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7

Specifications of your BTC6750GL cooker hood
PRODUCT DIMENSIONS
Height: 565 mm – 1045 mm
Width: 600 mm
Depth: 500 mm
DIMENSIONS OF CHIMNEY SECTION:
276 mm x 303 mm
Your stainless steel cooker hood is fitted with:
oHigh extraction tangential motor
oTouch control operation
oLCD display
o3 speeds
o1 metallic grease filter
o2 halogen lights
oCut off timer
Extraction capacity: 750 m³/hr
Noise level min/max: 58 – 64 dB
MODEL NUMBER CARBON FILTER REQUIRED
BTC6750GL S1
8

Specifications of your BTC9750GL cooker hood
PRODUCT DIMENSIONS
Height: 565 mm – 1045 mm
Width: 900 mm
Depth: 500 mm
DIMENSIONS OF CHIMNEY SECTION:
276 mm x 303 mm
Your stainless steel cooker hood is fitted with:
oHigh extraction tangential motor
oTouch control operation
oLCD display
o3 speeds
o1 metallic grease filter
o2 halogen lights
oCut off timer
Extraction capacity: 750 m³/hr
Noise level min/max: 58 – 64 dB
MODEL NUMBER CARBON FILTER REQUIRED
BTC9750GL S1
9

Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED
BEFORE THE COOKER HOOD IS USED FOR THE FIRST
TIME.
oYou should use a good quality stainless steel cleaner on ALL of
the stainless steel areas of your cooker hood, before it is used
for the first time.
oThis will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
oMake sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
oFind the control panel, which is located in the middle of the
canopy.
oThere are several buttons on the control panel, which perform
separate functions.
oPress the Add/ON button to switch the cooker hood on. The hood
will start to run at its lowest speed.
oThe cooker hood has three operating speeds; low, medium and
high. Use the Add/ON button to increase the speed and use the
Dec/OFF button to decrease the speed that it is operating at.
oThe operating speed that you have selected will appear on the
LCD display.
oIf you press the Dec/OFF button when the hood is operating at
its lowest speed, then the hood will switch off.
10

11
oPress the Light button to switch the bulbs on and off. You can
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
etting the time of day
oPress and hold the timer button, until the first two digits of the
oRelease the timer button, then use the Add/ON button and
oPress the timer button again and the second two digits of the
oUse the Add/ON button and Dec/OFF button to set the minute
oOnce the time of day is shown correctly on the display, press the
he timer
oYou can use the cooker hood’s timer, to set the cooker hood to
oYou can get the cooker hood to countdown for the following
No. of pushes of the timer Length of time (in minutes)
switch the lights on, even if the hood is not operating.
HOOD TEN MINUTES BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.
S
display start to flash.
Dec/OFF button to set the hour time.
display will start to flash.
time.
timer button for the third time to confirm it.
T
run for a particular period of time and then switch off.
periods of time:-
button the cooker hood will operate
for
1 5 minutes
2 15 minutes
3 30 minutes
4 Timer function cancelled
oOnce you have set a countdown period, the cooker hood will
oWhen the countdown time has been reached, 00:00 will appear
and the cooker hood will stop running.
start to countdown. The time remaining until the cooker hood
shuts off will show on the display.

Cleaning your Baumatic cooker hood
12
IMPORTANT: BEFORE CLEANING, ALWAYS
ENSURE THAT YOU HAVE SWITCHED YOUR
COOKER HOOD OFF AT THE OMNI-POLAR
SWITCH, SET AT THE WALL FROM THE CABLE.
Cleaning
oClean the external parts of your cooker hood with mild liquid
gent and a new damp cloth.
ive solvents or brushes.
.
uid
detergents and a new damp cloth.
recirculation mode, then be
sure to replace the carbon filter at the recommended interval
area above the grease filters.
deter
oNever use abrasive powder, corros
oNever insert pointed objects into the motor’s protective grid
oOnly clean the control panel and grease filter grill with mild liq
oIf you are using the appliance in
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
oNever attempt to clean the
The grease filter
oYour cooker hood includes a grease filter which helps to absorb
grease particles to protect your kitchen & furniture from greasy
llic filter may become inflammable if they become
saturated with this greasy residue.
should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at
ASH THE GREASE FILTER IN A DISHWASHER.
residues.
oThis meta
oTo prevent this fire hazard, the filter
least once a month, using hot water and normal washing-up
detergent.
oDO NOT W

13
aintenanceM
Removing and cleaning the grease filter
oFirst remove the grease filter by
pulling down on the handle and
about an hour.
Rinse it off thoroughly with hot water.
Repeat the process if required.
oRefit the grease filter once it has
dried.
oIMPORTANT: Let the grease filter dry thoroughly before
refitting it in the cooker hood.
pulling them away from the
cooker hood.
oSoak the grease filter in hot water and washing up liquid for
o
o

Changing a light bulb
14
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
T BULB, YOU MUST ENSURE THAT YOU
the grease filter (as
described on page 13).
e light bulbs ensure that they have cooled
ht fixture which is inside the exposed section of the
canopy.
oUse a screwdriver to remove the glass cover that sits over the
bulb. Unscrew the light bulb that needs to be replaced and insert
a new G4 20W (max) bulb. Then replace the glass cover.
If the lights still do not work, make sure that the bulbs are fitted
l
assistance.
oRefit the grease filter.
A LIGH
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
oRemove
oPrior to touching th
down.
oFind the bulb that requires replacement, you will find it located in
the lig
oIMPORTANT: Defective bulbs should be replaced immediately.
o
properly into their housings before you call for technica

F
15
itting the carbon filters
the appliance is being used to be used in recirculation mode then it
ilters. This will help to absorb unpleasant
dours caused by cooking.
THE CARBON FILTERS, YOU MUST
) Remove the grease filters.
) Hook the carbon filter over
e pins that are located at the
nd of the motor.
) Turn the carbon filter anticlockwise, until you feel
click into place.
oRepeat this process for the second carbon filter. You need to
place a carbon filter at either end of the motor.
oThe carbon filters should be replaced every three months or if
age.
If
is necessary to fit carbon f
o
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
1
2
th
e
3
it
oRefit the grease filter.
they show signs of dam

Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
he manufacturer declines all responsibility in the event of the installer
iling to observe all the accident prevention regulations in force,
hich are necessary for normal use and the regular operation of the
OUR COOKER HOOD IS INTENDED FOR FITTED AND
ATION.
ble must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
son, using
xed wiring via a double pole switched fused spur outlet.
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
T
fa
w
electric system.
Electrical connection
Y
PERMANENT INSTALL
oThe cooker hood’s power ca
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent per
16
fi
o is a member of the N.I.C.E.I.C. and who will comply
ith the I.E.E. and local regulations. The wires in the mains lead are
f you only find two wires in the main’s lead (blue and brown),
(UK ONLY).
We recommend that the appliance is connected by a
electrician, wh
qualified
w
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
I
then neither must be connected to the earth terminal.

17
oAs the colours of the wires in the appliance’s mains lead may not
eutral), or coloured
black.
l marked “L” (live), or coloured red.
oCheck that the product purchased is of a suitable size for the
addition check whether there is an
electrical socket available that will be accessible once the hood is
od.
n.
moved.
aterials, such as packets of screws,
guarantees etc. These should be removed and kept for future
heir position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
er hood
parts and fittings on to it.
r a qualified technician must verify the
suitability of the materials, in accordance with the type of wall
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
oThe blue wire must be connected to the
terminal marked “N” (n
oThe brown wire must be connected to the
termina
installationBefore beginning
chosen installation area. In
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
oCarry out all necessary masonry work prior to the fitting of the
cooker ho
oEnsure that all electrical connections are carried out by a suitably
qualified perso
oBefore commencing installation of the cooker hood the grease
filters should be re
oCheck inside the product and insure that there is no transit
packaging or any other m
use.
oIf possible, disconnect and move freestanding or slot-in cookers
from t
should be placed over the worktop, hob top or cooker. This will
help to protect these surfaces from damage and debris.
oSelect a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cook
oRawl plugs are provided to secure the hood to most types of
walls and ceilings. Howeve
and ceiling. The wall and ceiling must be strong enough to take
the weight of the hood.

oDo not tile, grout or silicone this appliance to the wall. This
appliance is designed to be surface mounted only.
Installing your cooker hood
18
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
e
MPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
INSTALLING YOUR
MODE. PLEASE TURN TO PAGE 24 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
commend that at least two people install this hood. oWe r
I
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filters.
) Position the hood against the wall that you are intending to
stall it on and mark the position of the support holes that are
be drilled (as shown in the figure below).
2
in
to

a) The support screw holes are indicated by figure Ain this drawing
nd the anchoring screw holes are indicated by figure B.
) Using a drill bit with a 8 mm
iameter, make holes in the wall on the
ositions that you have marked in step
4) Insert raw plugs into all of the holes that you have drilled.
5) Fasten the support screws halfway in, leaving them 10 mm out of
2
a
3
d
p
2.
19
the wall.

20
) Hang the hood onto the support
crews.
7) ing
crews (B) through the relevant holes in the cooker hood. Tighten the
6
s
Fully tighten the support screws (A) and then screw the anchor
s
anchoring screws fully into the wall