Bayside Furnishings Kavari 223243-30-00GT User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE
READ AND KEEP FOR FUTURE REFERENCE.
Bayside Furnishings Mfg., Inc. Page 1 Factory # 33-10944
Kavari TV Stand w/Gaming/Theatre Shelf
Model # 223243-30-00GT
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this item to
the store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
001-877-494-2536 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.baysidefurnishings.com EMAIL: [e-mail]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
LOT NUMBER:
DATE PURCHASED: / /
223243-30-00GT

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 2 Factory # 33-10944
MANUFACTURER: Bayside Furnishings
CATALOG: Kavari TV Stand w/Gaming/Theatre Shelf (223243-30-00GT)
DATE OF MANUFACTURE: August, 2011
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
FITS UP TO MOST 60” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
MAXIMUM LOAD 15 lb. (6.8 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
MAXIMUM LOAD 10 lb. (4.5 kg)
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION, TIPS and TRICKS
This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint
Hardware between the wall and the TV stand to prevent any accidents or damages. When
properly installed, this restraint can provide protection against the unexpected tipping of the
unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a
substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY
WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE
AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT
PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN CENTRE
OF UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS
COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
FITS UP TO MOST 60” FLAT PANEL TVs
WITHOUT SWIVELING FLOATER
MAXIMUM LOAD 135 lb. (61.2 kg)
PLACE TV BEHIND STOPPER

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 3 Factory # 33-10944
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
A- Top Shelf Frame (1) B- Base Assembly (1) C- Left Front Post (1)
D- Right Front Post (1) E- Short Spine (1) F- Wood Back Support (2)
G- Glass Top (1) H- Glass Shelf (1) I- Swiveling Floater Post (1)
J- Swiveling Bracket (1) K- XYZ Mounting Frame (1) L- Monitor Bracket (2)
M- SSS Spine (1) N- Sensor/Sound shelf (1) O- Gaming Guitar Clip (1) P- Cable Wheel (1)
(1) Suction Cup (8+1 extra) (2) 1/2” Bolt (4+1 extra) (3) 3/4” Bolt (23+1 extra)

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 4 Factory # 33-10944
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are
present before beginning assembly.
(4) 1” Bolt (8+1 extra) (5) 1-1/4” Bolt (4+1 extra) (6) 2-1/4” Bolt (4+1 extra)
(7) Lock Washer (40+2 extra) (8) Flat Washer (40+2 extra) (9) Glass Clamp w/Bolt (4+1 extra)
(10) Concrete Anchor (4) (11) 2-1/2” Lag Bolt (4) (12) Lag Bolt Washer (4+1 extra)
(13) Acrylic Stopper M4 Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (1)
(1) (2) (1) (Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)
M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen Wrench (provided) and Phillips Screwdriver (not provided).

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 5 Factory # 33-10944
Assembly Instructions
Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Align and attach Left and Right Front Posts (C and D) to the front corners of Base Assembly
(B).
3/4” Bolt
(2 used in this step)
③
1-1/4” Bolt
(2 used in this step)
⑤
Lock Washer
(4 used in this step)
⑦
Flat Washer
(4 used in this step)
⑧

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 6 Factory # 33-10944
Assembly Instructions
3. Stand last assembly upright. Attach the Short Spine (E) to the back of Base Assembly (B)
using four 3/4” Bolts (3) with Lock Washers (7) and Flat Washers (8). Tighten the Bolts with
M4 Allen Wrench provided.
Lock Washer
(4 used in this step)
⑦
Flat Washer
(4 used in this step)
⑧
3/4” Bolt
(4 used in this step)
③

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 7 Factory # 33-10944
Assembly Instructions
4. Align and attach the Top Shelf Frame (A) between Front Posts (C and D) and Spine (E).
Make sure that top edges are flush with each other and that the gaps and offsets between
the front rail of Top Shelf Frame and the Posts are equal. Loosen the bolts and adjust if
necessary.
3/4” Bolt
(4 used in this step)
③
1-1/4” Bolt
(2 used in this step)
⑤
Lock Washer
(6 used in this step)
⑦
Flat Washer
(6 used in this step)
⑧

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 8 Factory # 33-10944
Assembly Instructions
5. Attach 2 Wood Back Supports (F) to the back rail of Metal Frames using eight 1” Bolts (4)
with Washers (7 and 8). Make sure all the threaded inserts for Glass Clamps are level with
each other.
Lock Washer
(8 used in this step)
⑦
Flat Washer
(8 used in this step)
⑧
1” Bolt
(8 used in this step)
④

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 9 Factory # 33-10944
Assembly Instructions
6. Go back and tighten all bolts with enclosed Allen Wrench.
7. Adjust the Floor Levelers pre-attached at the bottom of Metal Base and Front Posts (C and
D) to level the unit.

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 10 Factory # 33-10944
Assembly Instructions
8. Attach Gaming Guitar Clip (O) and Cable Control (P) vertical onto the backside of Short
Spine (E). You can treat them as cable controls to help keep your entertainment center’s
cables and cords organized.
9. The Gaming Guitar Clip (O) can provide storage of gaming guitar controllers when you
attach it horizontally onto the backside of the Spine.
3/4” Bolt
(3 used in this step)
③
If you choose Table-top configuration,
continue to STEP 8.
If mounting TV with the Swinging Floater,
skip ahead to PAGE 14.

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 11 Factory # 33-10944
Assembly Instructions
10.Put the Suction Cups (1) firmly into the top holes of Top Shelf Frame (A) and attach the
Glass Clamps (9) to the threaded inserts on both Front Posts (C and D) and Wood Back
Supports (F). Make sure the set screw on the Glass Clamp is bottom.
Tip: If a suction cup resists insertion, try pressing down on the middle of the cup with the
Allen Wrench while twisting it clockwise into the hole.
11.Properly install the Glass Top and Glass Shelf (G and H) with the black side of glass down.
Rotating clockwise the Set Screw underneath Glass Clamps to secure the Glass Shelf in
place and to prevent falling easily and getting damage.
Note: If glass is scratched you can minimize the damage by using a BLACK marker and
filling in scratched area from underneath.
Glass Clamp w/Bolt
(4 used in this step)
⑨
Suction Cup
(8 used in this step)
①

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 12 Factory # 33-10944
Assembly Instructions
12.Remove the tape of Acrylic Stopper (13) and place it on the cut-out of the warning label on
the front of Glass Top (G). Make sure it is aligned before applying pressure.
13.Remove the warning label for Acrylic Stopper carefully.
Acrylic Stopper
(1 used in this step)
⑬

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 13 Factory # 33-10944
Assembly Instructions
14.Position the assembled Table-top in your desired location against the wall. Now follow the
instructions printed on the plastic bag containing the Tipping Restraint Hardware to mount
the Tipping Restraint Hardware Kit to one Wood Back Support (F) and the wall.
NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO
THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
15.The Table-top is ready for use now. Be sure to position your TV in center of console with no
overhang on either side.
NOTE: For Wall Mount, proceed to PAGE #23.
Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 14 Factory # 33-10944
16.Align and attach the Swiveling Floater Post (I) to the back of Short Spine (E). Make sure the
sockets for Cable Wheel facing backward.
Lock Washer
(4 used in this step)
⑦
Flat Washer
(4 used in this step)
⑧
Assembly Instructions for
Floating Swivel Mount
2-1/4” Bolt
(4 used in this step)
⑥

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 15 Factory # 33-10944
Assembly Instructions
17.Align and attach the Swiveling Bracket (J) to the top of Swiveling Floater Post (I) making
sure the pivoting bolt head is up. Tighten the bolts with enclosed M4 Allen Wrench.
Lock Washer
(6 used in this step)
⑦
Flat Washer
(6 used in this step)
⑧
3/4” Bolt
(6 used in this step)
③

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 16 Factory # 33-10944
Assembly Instructions
18.The Sensor/Sound Shelf (N) provides two options: position gaming accessories above TV or
sound bar below TV. Choose the option you prefer, slide SSS Spine (M) onto the XYZ
Mounting Frame (K) properly. Adjust the height of SSS Spine and attach in place. Make
sure the Sensor/Sound Shelf (N) will not hit your TV.
Lock Washer
(4 used in this step)
⑦
Flat Washer
(4 used in this step)
⑧
3/4” Bolt
(4 used in this step)
③

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 17 Factory # 33-10944
Assembly Instructions
19.Hold and attach the flat side of XYZ Mounting Frame (K) onto the Swiveling Bracket (J).
Make sure the recess holes on the XYZ Mounting Frame are at the bottom. Securely tighten
with enclosed Allen Wrench.
Lock Washer
(4 used in this step)
⑦
Flat Washer
(4 used in this step)
⑧
1/2” Bolt
(4 used in this step)
②

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 18 Factory # 33-10944
Assembly Instructions
20.Pick up Sensor/Sound Shelf (N) and securely fit the back tabs into the small slots of SSS
Spine (M). Tighten both lock bolts pre-attached on the SSS Spine with a Phillips
Screwdriver until they hit the back tabs of Sensor/Sound Shelf..

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 19 Factory # 33-10944
Mounting Monitor Bracket to a television with a flat back
Note: For televisions with a curved back or recessed back proceed directly to step #23.
21.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded inserts on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
22.Follow the appropriate diagram below to attach Monitor Brackets (L) to the back of your TV
with selected fasteners. Make sure the Monitor Brackets are centered and level with each
other. Secure the bolts with a Phillips Screwdriver. DO NOT over tighten the bolts.
NOTE: Lean the TV up against a wall or other solid surface when attaching with the Monitor
Brackets (L). DO NOT place the TV face down on the glass this may cause permanent
damage.

Please call for replacement parts or assistance: 001-877-494-2536
Bayside Furnishings Mfg., Inc. Page 20 Factory # 33-10944
Mounting Monitor Bracket to a television with a curved / recess back
23.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
24.Follow the appropriate diagram below to attach Monitor Brackets (L) to the back of your TV
with selected fasteners. Make sure the Monitor Brackets are vertically centered and level
with each other. Secure the bolts with a Phillips Screwdriver. DO NOT over tighten the bolts.