Bayside Furnishings Metrex CORC-7 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Bayside Furnishings® Page 1 Factory No. 16187
Metrex Mesh Chair
Model # CORC-7
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this
item to the store where it was purchased. Please call our toll-free customer service number
and have your instructions and parts list ready to provide the model name, part name or
factory number:
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our website www.baysidefurnishings.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

Model # CORC-7
Bayside Furnishings® Page 2 Factory No. 16187
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A – Back Assembly (1) B – Seat (1)
C – Mechanism (1) D – Gas Lift w/Telescoping Cover (1)
E – 5 Star Base (1) F – Caster (5)
(1) Ø5/16” x 3/4” Bolt (2) Ø5/16” x 1-3/4” Bolt
(Qty. 4+1 extra) (Qty. 4+1 extra)
(3) Allen Wrench (Qty. 1)
Tools required: Allen Wrench (provided).

Model # CORC-7
Bayside Furnishings® Page 3 Factory No. 16187
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. To begin assembly, place 5 Star Base (E) upside down and press the Casters (F) into the
holes at the end of each leg.
3. Turn the Star Base (E) upright and insert the thick end of the Gas Lift (D) into the center hole of
Star Base. Make sure the Telescoping Cover is over the Gas Lift (D) and rests on the Base.

Model # CORC-7
Bayside Furnishings® Page 4 Factory No. 16187
Assembly Instructions
4. Place the Seat (B) upside down onto the carton with the threaded holes facing up. Align and
attach the Mechanism (C) to the Seat (B) using four 3/4” Bolts (1). As shown below. Tighten
the bolts with the enclosed Allen Wrench.
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton to
prevent from scratching the chair material.
1
1
C
FRONT
B
Ø5/16” x 3/4” Bolt
(4 used in this step)
①

Model # CORC-7
Bayside Furnishings® Page 5 Factory No. 16187
Assembly Instructions
5. Pick up the Back Assembly (A) and fit the back support under the Mechanism (C) properly.
Insert four 1-3/4” Bolts (2) through the mounting holes on the Mechanism (C) and securely
screw into the threaded holes on the Back Assembly (A), using the enclosed Allen Wrench.
6. Turn the assembled seat upright and locate the centre hole of Mechanism (C) over the Gas
Lift (D). Press down firmly until the seat locks in place.
Ø5/16” x 1-3/4” Bolt
(4 used in this step)
②

Model # CORC-7
Bayside Furnishings® Page 6 Factory No. 16187
OPERATING INSTRUCTIONS
1.To Adjust Seat Height:
While seated, lean forward and reach under the right side of the chair to find the handle. Lift the
handle and raise your body up slightly to allow the chair to rise to the desired height. To lower
the seat, lift the handle while applying more weight downward on the seat. The chair will descend
until the handle is released or the chair reaches the bottom position.
2.To Operate Tilt Lockout:
While seated, reach under the right side of the chair to find the height adjustment handle. Pull
the handle all the way out (away from the gas lift) to allow the chair to tilt backwards. To lock the
chair in the upright or vertical position, sit upright and push the handle in towards the gas lift.
3.To Adjust Tension on The Tilt:
Reach under the front center of the chair, grasp the round knob and turn it counter-clockwise to
stiffen the tilt mechanism. Turn the knob clockwise to loosen the tilt mechanism. Turn the knob
until the desired resistance is reached.
4.To Adjust Height of The Armrest:
Press the buttons on the armrests to allow the armrests to move up or down freely. Release the
buttons once the desired height is reached.

Model # CORC-7
Bayside Furnishings® Page 7 Factory No. 16187
INFORMATION FOR USE
1. This is one type of office chair for commercial or home use. Please use it only on smooth, even
flooring.
2. The height of the seat can be raised up and down by adjusting the right side handle of the
mechanism. The back can tilt after you pull the side handle all the way out.
3. Please check all bolts, screws and knobs are tight at least every 3 months or as needed.
4. If parts are missing, broken, damaged or worn, please stop using this product until repairs are
done by a trained person.
5. Only a trained person may replace or repair seat height adjustment components with energy
accumulators.
Do not stand on this chair, do not use chair as a stepladder.
Use this product only for seating one person at one time.
Do not use this chair unless all bolts, screws and knobs are securely tightened.
Dispose of packing material properly. Do not use plastic cover as head covering. It may cause
suffocation.
Use this chair for its intended purpose only.
Use mild detergent only for cleaning.
Failure to follow these warnings could result in serious injury.
Maximum load weight on chair is 300 pounds (136 kg).
QUALITY GUARANTEE
We are confident that you will be delighted with your Bayside Furnishings purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Bayside Furnishings product is
designed to meet your highest expectations. We guarantee that you will immediately see the value of
our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
province to province (state to state).
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
ONLINE: www.baysidefurnishings.com
EMAIL: [email protected]
This unit is intended for use only within the maximum weights
indicated. Use with load than the maximum weights indicated may result in
instability, causing possible injury.
Imported by: Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
LIDCOMBE, NSW 2141
AUSTRALIA
Website: www.costco.com.au
MADE IN CHINA

IF YOU NEED TO ORDER ANY REPLACMENT PARTS, PLEASE USE THE LIST BELOW
Metrex Mesh Chair (CORC-7)
1
2
4
3
A
B
GG
C
H
D
J
K
*CORC-7-A-BR Backrest *CORC-7-K-PAC Pivot Arm Cap *CORC-7-B-S Seat *CORC-7-CH Complete Hardware *CORC-7-C-M Mechanism *CORC-7-1-3/4B Ø5/16” x 3/4” Bolt *CORC-7-D-GL Gas Lift *CORC-7-2-1 3/4B Ø5/16” x 1-3/4” Bolt *CORC-7-E-5SB 5 Star Base *CORC-7-3-TAW T-Handle Allen Wrench (5 mm) *CORC-7-F-C Caster *CORC-7-4-1 1/2B Ø1/4” x 1-1/2” Bolt (for back support) *CORC-7-G-ABS Arms and Back Support *CORC-7-5-5/8B Ø1/4” x 5/8” Bolt (for arm pad)
*CORC-7-H-TC Telescoping Cover *CORC-7-6-1/2B Ø1/4” x 1/2” Bolt *CORC-7-JL-LAP Left Armrest Pad *CORC-7-7-M4AW 4 mm Allen Wrench *CORC-7-JR-RAP Right Armrest Pad
4
H
E
F67
5