BBK 1898 User manual

WWW.BBKPERFORMANCE.COM
27427 BOSTIK COURT
TEMECULA, CA 92590
For any questions, email us:
[email protected]
INSTALLATION INSTRUCTIONS
INS251
2012-2018 FORD FOCUS (ST)
THROTTLE BODY
Part # 1898
Diculty: Average
Install Time: Approximately 1 - 2 hours.
UPDATED LAST: February 2018
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
MADE IN U.S.A.
Special Tools required: 7, 8, 10 and 13mm sockets and extensions, T-30 torx bit

UPDATED LAST: February 2018
WWW.BBKPERFORMANCE.COM
27427 BOSTIK COURT
TEMECULA, CA 92590
For any questions, email us:
[email protected]
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
MADE IN U.S.A.
STEP 1
Start with jacking up vehicle using level surface and support with jack stands
or work on a vehicle lift to access throttle body from underneath the vehicle.
Also disconnect positive battery cable using 10mm socket.
STEP 2
Start by loosening factory coupler clamp using 7mm socket do not remove.
STEP 3
From underneath vehicle remove factory chassis cover to access throttle
body using a T-30 torx bit. Now pull down on the intake tube to the throttle
body and set aside.
STEP 4
Now looking up at throttle body using 13mm socket disconnect power-wire
from alternator for better access to throttle body.
STEP 5
Disconnect signal plug from throttle body then using 8mm socket and
extensions remove factory throttle body.

WWW.BBKPERFORMANCE.COM
FOLLOWTHESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION
27427 BOSTIK COURT
TEMECULA, CA 92590
For any questions, email us:
[email protected]
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
UPDATED LAST: February 2018
MADE IN U.S.A.
STEP 6
Now reverse all processes installing BBK throttle body, alternator wire, intake
tube, chassis cover, etc.

WWW.BBKPERFORMANCE.COM
FOLLOWTHESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION
STEP 1
Disconnect battery for 5 minutes. Reconnect or use a code reader to clear any
stored codes in the computer.
NOTE: IF THIS IS A NEWINSTALL, PROCEED TO STEP 2.
STEP 2
Turn ignition key to on position, do not start the engine.
STEP 3
Slowly depress the gas pedal to the floor, and then slowly release it. Do
this three (3) times. On the third press hold pedal to the floor until the check
engine light flashes release the pedal and turn the key o.
STEP 4
Now start engine. The gas pedal is now in synch with the larger throttle body.
GAS PEDAL/THROTTLE BODY IDLE RELEARN PROCESS
With the addition of the larger bore throttle body and its larger intake ap, the gas pedal and throttle body must be re-synched before starting the engine.
This must be done to prevent a check engine light for “increased idle”. The procedure is simple.
After installation instructions are complete, please follow the procedures below. If throttle body has already been installed, please just follow steps 1-4.
27427 BOSTIK COURT
TEMECULA, CA 92590
For any questions, email us:
[email protected]
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
MADE IN U.S.A.
UPDATED LAST: February 2018