BCM Advanced Research MX310HD User manual

MX310HDUser’sManual
1
MX310HD
Intel® H310 PCH
Supports Coffee Lake (8th Gen)/
Coffee Lake Refresh (9th Gen)
i7/i5/i3/Pentium processors
(Supports “up to 6 Cores” and “up to
TDP 65W” type processors only)
Mini-iTX Motherboard
User’s Manual
Edition 1.01 – July, 2019

MX310HDUser’sManual
2
FCC Statement
THIS DEVICE SUPPORTS PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE
EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL,
MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH
CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Notice
This guide is designed for experienced users to setup the system within the shortest time. For detailed
information, please always refer to the electronic user's manual.
Copyright Notice
Copyright ©2011 BCM Advanced Research, ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the prior written permission of the original
manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.

MX310HDUser’sManual
3
Disclaimer
BCM Advanced Research reserves the right to make changes, without notice, to any product, including
circuits and/or software described or contained in this manual in order to improve design and/or
performance. BCM Advanced Research assumes no responsibility or liability for the use of the described
product(s), conveys no license or title under any patent, copyright, or masks work rights to these products,
and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described in this manual are for
illustration purposes only. BCM Advanced Research makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
BCM Advanced Research PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF BCM Advanced
Research.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in significant injury to
the user.
2. A critical component is any component of a life support device or system whose failure to perform can
be reasonably expected to cause the failure of the life support device or system, or to affect its safety
or effectiveness.

MX310HDUser’sManual
4
A Message to the Customer
BCM Customer Services
Each and every BCM product is built to the most exacting specifications to ensure reliable performance in
the harsh and demanding conditions typical of industrial environments. Whether your new BCM device is
destined for the laboratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name BCM has come to be known.
Your satisfaction is our primary concern. Here is a guide to BCM customer services. To ensure you get the
full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into technical difficulties,
we are here to help. For the most frequently asked questions, you can easily find answers in your product
documentation. These answers are normally a lot more detailed than the ones we can give over the phone.
So please consult the user’s manual first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.bcmcom.com.
If you still cannot find the answer, gather all the information or questions that apply to your problem, and
with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the
support you need to get the most from your BCM products. In fact, most problems reported are minor and
are able to be easily solved over the phone.
In addition, free technical support is available from BCM engineers every business day. We are always
ready to give advice on application requirements or specific information on the installation and operation of
any of our products. Please do not hesitate to call or e-mail us.
BCM Advanced Research
11 Chrysler,
Irvine, California, 92618
USA
Tel : [phone]
Fax : [phone]
http://www.bcmcom.com
E-mail: [email protected]

MX310HDUser’sManual
5
Product Warranty
BCM warrants to you, the original purchaser, that each of its products will be free from defects in materials
and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons other than
repair personnel authorized by BCM, or which have been subject to misuse, abuse, accident or improper
installation. BCM assumes no liability under the terms of this warranty as a consequence of such events.
Because of BCM high quality-control standards and rigorous testing, most of our customers never need to
use our repair service. If any of BCM products is defective, it will be repaired or replaced at no charge
during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of
replacement materials, service time, and freight. Please consult your dealer for more details. If you think
you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU type and speed, BCM
products model name, hardware & BIOS revision number, other hardware and software used, etc.)
Note anything abnormal and list any on-screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any helpful
information available.
3. If your product is diagnosed as defective, obtain an RMA (return material authorization) number from
your dealer. This allows us to process your good return more quickly.
4. Carefully pack the defective product, a complete Repair and Replacement Order Card and a
photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

MX310HDUser’sManual
6
Manual Objectives
This manual describes in detail the BCM MX310HD Main board.
We strongly recommend that you study this manual carefully before attempting to interface with this
mainboard or change the standard configurations. Whilst all the necessary information is available in this
manual we would recommend that unless you are confident, you contact your supplier for guidance.
Please be aware that it is possible to create configurations within the CMOS RAM that make booting
impossible. If this should happen, clear the CMOS settings, (see the description of the Jumper Settings for
details).
If you have any suggestions or find any errors concerning this manual and want to inform us of these,
please contact our Customer Service department with the relevant details.
Safety Precautions
Warning!
Always completely disconnect the power cord from your chassis whenever you
work with the hardware. Do not make connections while the power is on. Sensitive
electronic components can be damaged by sudden power surges. Only
experienced electronics personnel should open the PC chassis.
Caution!
Always ground yourself to remove any static charge before touching the
mainboard. Modern electronic devices are very sensitive to static electric charges.
As a safety precaution, use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded bag when they are not
in the chassis.
Document Amendment History
Revision Date Comment
1st (1.00) June, 2019 Initial Release
2nd (1.01) July, 2019 Updated 4-pin ATX connector wide range info

MX310HDUser’sManual
7
Contents
Chapter 1: System Setup ..............................................................................................15
1.1 Welcome!......................................................................................................................................15
1.2 Packing Contents..........................................................................................................................15
1.3 Before you proceed.......................................................................................................................16
1.4 Mainboard Overview.....................................................................................................................17
1.4.1 Mounting Holes.............................................................................................................................17
1.4.2 Mainboard Layout.........................................................................................................................18
1.4.3 Layout Content List.......................................................................................................................19
1.4.3.1 Slots..............................................................................................................................................19
1.4.3.2 Internal Jumpers...........................................................................................................................19
1.4.3.3 Internal Headers ...........................................................................................................................20
1.4.3.4 Back Panel Connectors ................................................................................................................21
1.5 Central Processing Unit (CPU).....................................................................................................22
1.5.1 Installing the CPU .........................................................................................................................23
1.5.2 Installing the CPU Heatsink and Fan............................................................................................27
1.5.3 UnInstalling the CPU Heatsink and Fan .......................................................................................29
1.6 System Memroy............................................................................................................................31
1.6.1 Overview.......................................................................................................................................31
1.6.2 Memory Configurations.................................................................................................................32
1.6.3 Installing the DDR4 SODIMM.......................................................................................................33
1.6.4 Removing the DDR4 SODIMM...................................................................................34
1.7 Power Supply................................................................................................................................35
1.7.1 12V DC-In Power Connector: J_ATX-IN (4-Pin)...........................................................................35
1.8 Back Panel (Rear I/O Ports) .........................................................................................................36
1.8.1 Back Panel Connectors ................................................................................................................36
1.9 Connectors/Headers.....................................................................................................................38
1.9.1 Front Panel Connectors: J_FR_PANEL .......................................................................................38
1.9.2 Serail ATA 3.0 Connectors: J_SATA3-1, J_SATA3-2 ..................................................................38
1.9.3 Serail ATA Power Connector: J_SATA-PWR...............................................................................39
1.9.4 CPU & System Fan Connectors: J_CPU-FAN, J_SYS-FAN........................................................39
1.9.5 Front Panel Audio Connectors: J_FR-AUDIO ..............................................................................40
1.9.6 Amplifier Connector: J_AMP-OUT................................................................................................40
1.9.7 Front USB3.0 Headers: J_USB3-12.............................................................................................41
1.9.8 Front USB2.0 Headers: J_USB2-56.............................................................................................41

MX310HDUser’sManual
8
1.9.9 Serail Port Connector: J_COM1, J_COM2...................................................................................42
1.9.10 LVDS Header: J_LVDS.................................................................................................................42
1.9.11 LVDS Panel Backlight Connector: J_BACKLIGHT.......................................................................43
1.9.12 SPI Header: J_SPI........................................................................................................................43
1.9.13 I2S Header: J_I2S.........................................................................................................................44
1.9.14 I2C Header: J_I2C........................................................................................................................44
1.9.15 GPIO Header: J_GPIO .................................................................................................................45
1.9.16 Chassis Intrusion Header: J_CHASSIS........................................................................................45
1.10 Jumpers ........................................................................................................................................46
1.10.1 ATX/AT Mode Selection: JP4........................................................................................................46
1.10.2 LVDS PWM Backlight Power Select: JP1.....................................................................................46
1.10.3 COM1 Ring-In/ +12V/ +5V Select: JP5.........................................................................................47
1.10.4 COM2 Ring-In/ +12V/ +5V Select: JP6.........................................................................................47
1.10.5 LVDS Brightness Mode Select: JP2 .............................................................................................48
1.10.6 Clear CMOS Jumper: JP3 ............................................................................................................49
1.11 The Expansion Slots.....................................................................................................................50
1.11.1 Installation of Expansion Card......................................................................................................50
1.11.2 Setup An Expansion Card.............................................................................................................50
1.11.3 PCIe x4 Slot: J_PCIE4X ...............................................................................................................51
1.11.4 M.2 Sockets ..................................................................................................................................52
1.11.4.1 M.2 Socket (M-Key): J_M2M ........................................................................................................52
1.11.4.2 M.2 Socket (E-Key): J_M2E..........................................................................................................52
Chapter 2: Starting Up the System .............................................................................53
2.1 Starting Up Your System...............................................................................................................53
Chapter 3: BIOS Setup ..................................................................................................55
3.1 BIOS Falsh Related Procedure ....................................................................................................55
3.2 Introducing BIOS...........................................................................................................................55
3.3 Entering BIOS Setup Menu...........................................................................................................56
3.4 Getting Help..................................................................................................................................56
3.5 BIOS Menu Screen.......................................................................................................................57
3.6 Main Menu ....................................................................................................................................58
3.7 Advanced Menu............................................................................................................................59
3.7.1 CPU Configuration........................................................................................................................59
3.7.1.1 Intel (VMX) Virtualization Technology...........................................................................................59
3.7.1.2 Active Processor Cores ................................................................................................................59
3.7.1.3 Hyper-Threading...........................................................................................................................59

MX310HDUser’sManual
9
3.7.1.4 Intel® Speedstep ..........................................................................................................................59
3.7.1.5 C States .......................................................................................................................................59
3.7.1.6 Enhanced C-States.......................................................................................................................59
3.7.1.7 Package C State Limit ..................................................................................................................59
3.7.2 PCH-FW Configuration.................................................................................................................60
3.7.3 Trusted Computing .......................................................................................................................60
3.7.4 ACPI Settings................................................................................................................................60
3.7.4.1 Enable Hibernation .......................................................................................................................60
3.7.4.2 ACPI Sleep State..........................................................................................................................60
3.7.4.3 PCIe# Wake from S5 (Wake on LAN2) ........................................................................................60
3.7.5 Super IO Configurtion...................................................................................................................61
3.7.5.1 Serial Port 1 Configuration............................................................................................................61
3.7.5.2 Serial Port 2 Configuration............................................................................................................61
3.7.3.3 WatchDog Count Mode.................................................................................................................61
3.7.5.4 WatchDog TimeOut Value.............................................................................................................61
3.7.5.5 Chassis Opened Warning.............................................................................................................61
3.7.5.6 ErP/EuP S5 Support.....................................................................................................................61
3.7.6 HW Monitor...................................................................................................................................62
3.7.6.1 Smart Fan .....................................................................................................................................62
3.7.6.1.1 Smart Fan Function ......................................................................................................................62
3.7.6.1.2 Smart Fan Mode Configuration.....................................................................................................62
3.7.7 Intel TXT Information.....................................................................................................................62
3.7.8 USB Configuration........................................................................................................................63
3.7.8.1 Legacy USB Support ....................................................................................................................63
3.7.8.2 XHCI Hand-off...............................................................................................................................63
3.7.8.3 USB Mass Storage Driver Support...............................................................................................63
3.7.9 Network Stack Configuration ........................................................................................................64
3.7.9.1 Network Stack...............................................................................................................................64
3.7.9.2 IPv4 PXE Support.........................................................................................................................64
3.7.9.3 IPv6 PXE Support.........................................................................................................................64
3.7.9.4 PXE boot wait time........................................................................................................................64
3.7.10 CSM Configuration........................................................................................................................65
3.7.10.1 CSM Support.................................................................................................................................65
3.7.10.2 Boot Option Filter..........................................................................................................................65
3.8 Chipset..........................................................................................................................................66
3.8.1 System Agent (SA) Configuration.................................................................................................66

MX310HDUser’sManual
10
3.8.1.1 Memory Configuration...................................................................................................................66
3.8.1.1.1 Max TOLUD..................................................................................................................................66
3.8.1.2 Graphics Configuraiton.................................................................................................................66
3.8.1.2.1 Primary Display.............................................................................................................................66
3.8.1.2.2 Internal Graphics...........................................................................................................................66
3.8.1.2.3 DVMT Pre-Allocated.....................................................................................................................66
3.8.1.2.4 DVMT Total Gfx Mem....................................................................................................................66
3.8.1.3 LCD Control...................................................................................................................................66
3.8.1.3.1 LVDS Control ................................................................................................................................66
3.8.1.3.2 LVDS Panel Type .........................................................................................................................67
3.8.1.3.3 LCD Brightness Control................................................................................................................67
3.8.1.3.4 LVDS PWM Brightness Control ...................................................................................................67
3.8.1.3 VT-d ..............................................................................................................................................67
3.8.2 PCH-IO Configuration...................................................................................................................67
3.8.2.1 PCI Express Configuration............................................................................................................67
3.8.2.2 SATA And RST Configuration.......................................................................................................67
3.8.2.3 USB Configuration........................................................................................................................67
3.8.2.4 HD Audio Configuration ................................................................................................................67
3.8.2.5 LAN1 Controller ............................................................................................................................67
3.8.2.6. Wake on LAN1 from S3/S4/S5 .....................................................................................................67
3.8.2.7 LAN2 Controller ............................................................................................................................67
3.8.2.8 Restore AC Power Loss................................................................................................................68
3.8.2.9 Serial Port 2 Configuration............................................................................................................68
3.8.2.10 Amplifier GAIN (db).......................................................................................................................68
3.9 Security.........................................................................................................................................69
3.10 Boot...............................................................................................................................................70
3.10.1 Setu Prompt Timeout....................................................................................................................70
3.10.2 Bootup NumLock State.................................................................................................................70
3.10.3 Quiet Boot.....................................................................................................................................70
3.10.4 Boot Mode.....................................................................................................................................70
3.10.5 FIXED BOOT ORDER Priorities...................................................................................................70
3.10.6 UEFI Hard Disk Drive BBS Priorities............................................................................................70
3.11 Save & Exit....................................................................................................................................71
3.11.1 Save Changes and Exit ................................................................................................................71
3.11.2 Discard Changes and Exit ............................................................................................................71
3.11.3 Save Changes and Reset.............................................................................................................71

MX310HDUser’sManual
11
3.11.4 Load Optimized Default ................................................................................................................71
Chapter 4: Application Note.............................................................................................................72
4.1 Windows 10 Drivers Installation....................................................................................................72
4.2 Display through PCIe video card (installed on "J_PCIEX4" slot)..................................................73
4.3 PXE Boot.......................................................................................................................................74

MX310HDUser’sManual
12
Mainboard Specifications
Model MX310HD
Processor Intel® H310 PCH Supports Coffee Lake (8th Gen)/ Coffee Lake Refresh (9th Gen)
i7/i5/i3/Pentium processors
(Supports “up to 6 Cores” and “up to TDP 65W” type processors only)
Chipset Intel® H310 PCH
Memory 2x 260-pins SODIMM sockets support 1.2V, Non-ECC, Un-buffered DDR4-2400
(PC4-19200) memory module, 2400 MHz up to 32GB (16GB maximum/slot)
Display Intel® Integrated Graphic Engine
Maximum Resolution DP: 4096 x 2304 @ 60Hz, 24bpp
HDMI: 4096 x 2160 @ 30Hz, 24bpp
LVDS: 1920x1200
SATA 2 x SATA III connectors
1 x SATA power connector
M.2 1x M.2 Type M 2242, 2280 Slot (with USB, PCIe x2 & SATA III)
1 x M.2 Type E 2230 (with USB & PCIe x1)
USB 4 x USB 2.0 ports (2@ 1x Header, 2@ Rear I/O)
4 x USB 3.0 ports (2@ 1x Header, 2@ Rear I/O)
TPM 1 x TPM 2.0 Security Device (Infineon® TPM Chip SLB9665)
Super I/O Controller Nuvoton® NCT6106D
Serial Ports 2 x RS-232 2.0mm Locking Type Headers (with Voltage Selection)
PCIe 1 x PCIe x4 Slot
Watch Dog Timer 1sec ~ 255 min timer
HW Monitor Yes
Audio Realtek® ALC892
HD Audio Codec with auto jack sensing
LAN Intel® i211-AT PCIe Gigabit LAN
1 x 10/100/1000 LAN Port
Intel® i219-LM PHY Gigabit LAN
1 x 10/100/1000 LAN Port
DIO 8 Bit
BIOS AMI® UEFI BIOS
AMI BIOS with 128Mb SPI ROM

MX310HDUser’sManual
13
Onboard I/O Headers
SATA 2 x Std. SATA III Connectors
1 x SATA Power Header
USB 1 x USB2.0 Header (2 ports/header)
1 x USB3.0 Header (2 ports/header)
RS232 2 x Headers
Front Audio 1 x Header
Amplifier 1 x Header
Front Panel 1 x Header
Fan Header 2 x Headers (12V, 4-pins)
LVDS 1 x Header for LVDS Panel Connection
1 x Header for LVDS Panel Backlight Connector
SPI 1 x Header
I2S 1 x Header
I2C 1 x Header
GPIO 1 x Header
Chassis Intrusion 1 x Header
Onboard Jumpers
COM Port Ring-In/ Power Select 2 x Headers provides Selection of “Ring-In”, or “12V” or “5V” on COM ports
AT/ATX Select 1 x Header
Clear CMOS 1 x Header
LVDS Brightness Mode Select 1 x Header
LVDS PWM Backlight Power Select 1 x Header
Rear I/O Ports
HDMI 1 x HDMI Connector
DP (Display Port) 1 x DP Connector
USB3.0 1x Stack up USB3.0 Connector
USB2.0 1x Stack up USB2.0 Connector
LAN 2 x 10/100/1000 LAN Ports
Audio 1 x Line-Out
1 x Mic-In
Power 1 x DC Connector

MX310HDUser’sManual
14
Power & Connector
1 x 4 pin ATX Connector (12V-24V Wide Range, Max. current ~8A)
1 x DC Connector (12V-24V Wide Range DC-In)
For +12V AC adapter, Max. current ~8A.
For +19V AC adapter, Max. current ~8A.
Form Factor
Mini-iTX 6.7” x 6.7”

MX310HDUser’sManual
15
Chapter 1: System Setup
This chapter describes the mainboard features and the new technologies it supports
1.1 Welcome!
The mainboard delivers a host of new features and latest technologies, making it another line of BCM
long life mainboards! Before you start installing the mainboard, and hardware devices on it, check the
items in your package with the list below.
If any of the items listed below is damaged of missing, please contact with your vendor.
1.2 Packing Contents
• Mainboard
• 1 x MX310HD
• Cable
• 1 x SATA Power Cable
• Accessories
• 1 x MX310HD I/O Shield

MX310HDUser’sManual
16
1.3 Before you proceed
Take note of the following precautions before you install mainboard components or change
any mainboard settings.
• Unplug the power cord from the wall socket before touching any component inside the
system.
• Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the
power supply case, before handling components to avoid damaging them due to static
electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag
that came with the component.
• Before you install or remove any component, ensure that the power supply is switched off or
the power cord is detached from the power supply. Failure to do so may cause severe
damage to the mainboard, peripherals, and/or components.

MX310HDUser’sManual
17
1.4 Mainboard Overview
Before you install the mainboard, study the configuration of your chassis to ensure that the
mainboard fits into it.
Make sure to unplug the power cord before installing or removing the mainboard. Failure
to do so can cause you physical injury and damage mainboard components.
1.4.1 Mounting Holes
Place the screws into the mounting holes indicated by red squares to secure the mainboard to
the chassis.
Do not over-tighten the screws! Doing so may damage the mainboard.

MX310HDUser’sManual
18
1.4.2 Mainboard Layout

MX310HDUser’sManual
19
1.4.3 Layout Content List
• 1.4.3.1 Slots
Label Function Note Page
J_SODIMM1 260-pin DDR4 SODIMM slot 1 20
J_SODIMM2 260-pin DDR4 SODIMM slot 2 20
J_M2E M.2 E-Key Supports WIFI Cards in 2230 39
J_M2M M.2 M-Key Supports SATA Type SSDs in
2242, or 2280
39
J_PCIE4X PCIe x4 slot
• 1.4.3.2 Internal Jumpers
Label Function Note Page
JP1 LVDS PWM Backlight Power
Select (+3.3V (default) /+5V)
1 x 3 header, pitch 2.00mm
JP2 LVDS Brightness Mode Select
(PWM Mode (default) /DC Mode)
1 x 3 header, pitch 2.00mm
JP3 Clear CMOS 1 x 3 header, pitch 2.00mm 36
JP4 ATX/AT Mode Select
(ATX Mode (default) / AT Mode)
1 x 3 header, pitch 2.00mm
JP5 COM1 Ring-In (default) / +12V/ +5V
Select
2 x 3 header, pitch 2.00mm
JP6 COM2 Ring-In (default) / +12V/ +5V
Select
2 x 3 header, pitch 2.00mm

MX310HDUser’sManual
20
• 1.4.3.3 Internal Headers
Label Function Note Page
J_ATX-IN 12V ATX Power Connector 2x 2 header,
12V-24V Wide Range,
Max. current ~8A
24
J_CPU-FAN CPU Fan Connector 4 x 1 wafer, Pitch 2.54mm 29
J_SYS-FAN System Fan Connector 4 x 1 wafer, Pitch 2.54mm
J_SATA3-1
J_SATA3-2
Serial ATA 3.0 Connectors 1, 2 7-pin header 27
J_SATA-PWR SATA Power Connector
J_COM1
J_COM2
Serial Port 1, 2 2 x 5 wafer header, pitch 2.00mm 31
J_USB2-56 USB2.0 Port 5, 6 2 x 5 box header, pitch 2.54mm 31
J_USB3-12 USB3.0 Port 1, 2 2 x 10 box header, pitch 2.00mm
J_FR-PANEL System Panel Connector 2 x 5 header, pitch 2.54mm 32
J_FR-AUDIO Front Panel Audio Connector 2 x 5 header, pitch 2.54mm 30
J_AMP-OUT Amplifier Connector 4 x 1 wafer header, pitch 2.00mm 30
J_LVDS LVDS Panel Connector 20 x 2 header, 1.25mm pitch wire
to board connector (WTB)
33
J_BACKLIGHT LVDS Panel Backlight Connector 1 x 5 wafer header, pitch 2.00mm 33
J_I2C I2C Connector 1 x 4 header, 2.00mm 34
J_SPI SPI Connector 2 x 4 header, 2.00mm
J_I2S I2S Connector 1 x 6 wafer header, 2.00mm
J_LPC LPC Connector 2 x 7 header, 2.00mm
J_GPIO GPIO Connector 2 x 5 wafer header, 2.00mm
J_CHASSIS Chassis Intrusion Connector 1 x 2 wafer header, 2.00mm