Bea Maglocks 600lb User manual

75.5366.10 MAGLOCKS 600lb 20230828 Page 1 of 4

MAGLOCKS 600LB

USER’S GUIDE

ELECTROMAGNETIC LOCKS

ENGLISH

door conguration door status sensor

single double with without

10MAGLOCK3UL  

10MAGLOCK3ULDS  

10MAGLOCK6UL  

10MAGLOCK6ULDS  

DESCRIPTION 10MAGLOCK3UL

10MAGLOCK3ULDS

10MAGLOCK6UL

10MAGLOCK6ULDS

Lock: single double

Input Voltage: 12 or 24 VDC 12 or 24 VDC

Bond Status Relay (when

powered):

1.0 A @ 24 VDC

resistive

1.0 A @ 24 VDC

resistive

Relay Power Factor: 1 1

Door Status Switch: dry contacts: 3W (switching contact 0.25 amps

max, switching voltage 30VDC max; resistive load)

dry contacts: 3W (switching contact 0.25 amps

max, switching voltage 30VDC max; resistive load)

Reed Switch Power Factor: 1 1

Power Consumption: 500 mA @ 12 VDC /

250 mA @ 24 VDC

500 mA @ 12 VDC /

250 mA @ 24 VDC each

Dimensions: 9.84 × 1.66 × 1.04 in

250 × 42.2 × 26.5 mm

19.685 × 1.66 × 1.04 in

500 × 42.2 × 26.5 mm

Certication: UL294 UL294

Operating Temperature: 32 – 120 °F (0 – 49 °C) 32 – 120 °F (0 – 49 °C)

Operating Humidity: 0 – 85% 0 – 85%

UL 294 Performance Ratings:

(required per Chapter 10 of 2015 IBC)

Destructive: Level I Line Security: Level I

Endurance: Level IV Standby Power: Level I

Static Strength: 500 lb Dynamic Strength: 33 ft/lb

NOTE: The specications listed above are for an indoor, dry,

installation location.

The Electromagnetic Lock (Maglock) series is a surface-

mounted, magnetic-lock assembly. They are available in

single- and double-lock varieties, various sizes (i.e. force),

and also avaible with or without built-in Door Status Switch

(“DS” versions). All models are designed for standard

installation on most types of doors (1 3⁄8to 2” thickness).

1 Description

ATTENTION: This product must be powered from a UL-listed, regulated, power-limited, power supply!

2 Specications

345

75.5366.10 MAGLOCKS 600lb 20230828 Page 2 of 4

5Handle the equipment with care. Damaging the mating surfaces of the magnet and armature plate may reduce locking efciency.

5The MAGLCOK mounts rigidly to the door frame. The armature plate mounts to the door with the hardware provided. This allows the armature plate to pivot about its

center to compensate for door wear and misalignment.

5You must only use the template with the door in its normally closed position.

5Add threadlocker to all screws before installing, and rmly tighten screws.

5Install only for indoor, dry applications.

5Installation and wiring must be performed in compliance with ANSI / NFPA 70 / NFPA 101 / CSA C22.1, Canadian Electrical Code, Part I, safety standard for electrical

installations, section 32; and CAN/ULC-S524 installation of re alarm system requirements.

5The MAGLOCK shall be installed within the same room as other equipment and circuitry connecting to the MAGLOCK.

5Wiring must be cased to avoid outer cable damage, affect the insulation distance.

5An electric locking mechanism shall not impair the operation of panic hardware mounted on the door.

5An electric locking mechanism shall not impair the intended operation of an emergency exit.

5Shut off all power going to header before attempting any wiring procedures.

5Maintain a clean and safe environment when working in public areas.

5Constantly be aware of pedestrian trafc around the door area.

5Always stop pedestrian trafc through the doorway when performing tests that may result in unexpected reactions by the door.

5Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment

or cable insulation.

5Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

DO NOT over-tighten the armature plate.

The rubber washer is designed to allow the armature plate to

automatically adjust position for best mating position between

the magnet and armature plate.

DOOR FRAME

MAGNET

DOOR

MOUNTING PLATE

Use the applicable mounting template.

ARMATURE PLATE

3 Precautions

4 Installation Notes

5 Installation – Mechanical

TYPICAL INSTALLATION

CAUTION

6 Armature Plate Installation

DOOR

nut

spacer

screw

(M8 45mm)

Apply threadlocker directly to all screws before

installing, and then rmly tighten the screws.

1. hole for nut

2. hole for guide pin

3. steel washer

4. rubber washer

5. steel washer

6. armature plate

7. permanent magnet (door status switch)

Ensure proper orientation of armature plate (i.e.

magnet positioned in upper left or right corner -

see diagram)

8. guide pin

DOOR

SIDE VIEW

armature plate

nut

rubber washer

Page 2 of 2 75.5366.02 20140401

5 Installation - Mechanical & Electrical

LOCK STATUS SWITCH (SPDT)

POWER

SUPPLY

+ -

POWER

SELECTOR

JUMPER

LED

MAG BOND SENSOR

MAGNET

TIMER (0-90 SEC)

TYPICAL INSTALLATION

NOTE: DO NOT over-tighten the armature plate. The rubber washer is designed to allow the armature

plate to automatically adjust position for best mating position between the lock and armature plate.

DOOR FRAME

ARMATURE PLATE

MAGNET

ANGLE

BRACKET

MOUNTING

PLATE

MOUNTING

PLATE

STRINGER

HOLE FOR

GUIDE PIN

HOLE FOR NUT

RUBBER WASHER

STEEL WASHER

ARMATURE PLATE

SCREW M8 (35MM)

GUIDE PIN

DOOR

NUT

SPACER

WASHER

ARMATURE

PLATE

DOOR

NUT

DOOR FRAME DOOR FRAME

DOOR

ARMATURE PLATE ARMATURE PLATE

MAGNET MAGNET

DOOR DOOR

MOUNTING

PLATE

CAUTION: Observe proper

circuit board orientation!

NOTE: The product must be powered from a UL listed, regulated, power limited, power supply.

NOTE: If power switch is not wired between DC source voltage and magnet,

it will take a longer time to de-energize the magnet simulating residual magnetism.

1. 12 VDC INPUT

A. Required power 0.5A (Max).

B. Connect ground (-) lead from a 12 VDC power source to Terminal 2.

C. Connect positive (+) lead from a 12 VDC power source to Terminal 1.

D. Check jumper for 12 VDC operation.

2. 24 VDC INPUT

A. Required power 0.25A (Max).

B. Connect ground (-) lead from a 24 VDC power source to Terminal 2.

C. Connect positive (+) lead from a 24 VDC power source to Terminal 1.

D. Check jumper for 24 VDC operation.

3. CONTACTS

1. Relay dry contacts are rated 1A at 24 VDC for safe operation, DO NOT exceed this

rating.

2. If a NO switch is required, connect the wires from the system to Terminal 4 & Terminal 3.

3. If a NC switch is required, connect the wires from the system to Terminal 4 & Terminal 5.

DS VERSION

24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.beasensors.com

75.5366.10 MAGLOCKS 600lb 20230828 Page 3 of 4

7 Installation – Electrical

power selector jumper

magnet

24 VDC

12 VDC

power

supply

CIRCUIT BOARD

NOTE: Terminals ratings: 16~22AWG (copper wire)

lock status switch

(SPDT)

timer

1 90

1~90s ±15s

bond sensor

red green

black

NO NC

red

green

LED

With lock sensor, LED, and timer

With lock sensor and LED

Reed switch (door sensor type) - optional

Unmonitored

2 (-)

1 (+)

3 N.O.

4 COM

5 N.C.

The product must be powered from a UL-listed, regulated, power-limited, power supply.

12 VDC INPUT

- Required power: 0.5 AMP / 12 VDC

- Connect positive (+) lead from a 12 VDC power source to Terminal 1.

- Connect negative (-) lead from a 12 VDC power source to Terminal 2.

- Check jumper for 12 VDC operation.

24 VDC INPUT

- Required power: 0.25 AMP / 24 VDC

- Connect positive (+) lead from a 24 VDC power source to Terminal 1.

- Connect negative (-) lead from a 24 VDC power source to Terminal 2.

- Check jumper for 24 VDC operation.

POWER

If power switch is not wired between DC source voltage(+) and magnet, it will take a longer time to de-energize the magnet simulating

residual magnetism.

75.5366.10 MAGLOCKS 600lb 20230828 Page 4 of 4

LOCK STATUS RELAY CONTACT (SPDT) AND DOOR STATUS SWITCH

- Relay dry contacts are rated 1A at 24 VDC for safe operation, DO NOT exceed this rating.

- The reed switch dry contacts are rated at 3W (switching contact 0.25 amps max, switching

voltage 30VDC max; resistive load) for safe operation.

- If a NO switch is required, connect the wires from the system to Terminal 3 and Terminal 4.

- If a NC switch is required, connect the wires from the system to Terminal 4 and Terminal 5.

7 Installation – Electrical (cont.)

SWITCHES (optional)

BEA Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA Inc.

does not guarantee any use of the sensor/device outside its intended purpose.

BEA Inc. strongly recommends that installation and service technicians be AAADM-certiﬁed for pedestrian doors, IDA-certiﬁed for doors/gates, and

factory-trained for the type of door/gate system.

Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/