BEC M2M MX-1000e User manual

M2M
Model: MX-1000(e)
Quick Install Guide
WHAT’S IN THE BOX
SETTING UP THE ROUTER
1 x BEC MX-1000(e) M2M Router
1 x This Quick Install Guide
1 x Mounting Bracket
1 x MiniFIT to DC Jack Power Cable
1 x Vehicle Power Cable
1 x DC Power Adapter 12VDC 1.2A
2 x Wi-Fi Antennas
3G/4G Antennas
Active GPS Antenna
Ethernet (RJ-45) Cable
(Optional Accessories)
1Insert the SIM Card
Note: Power o the MX-1000(e) before inserting/removing the SIM
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
Remove the SIM cover
then insert the SIM card(s)
(2FF) with the mental
contacts (gold plate) facing
up to the SIM slot(s) then
push it all the way in until
you hear the clicking sound. Replace the metal SIM cover
after inserting the SIMs.
2Attach the Wi-Fi Antennas
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
WAN1
MAIN
WIFI WIFI
WAN1
MAIN
WIFI WIFI
Note: Use the plastic red caps to cover unused antenna ports
Screw the 2 female Wi-Fi
antenna cable connectors
until fully attached to the
Wi-Fi ports on MX-1000(e).
Do not over-torque the
antenna on the connector.
3Attach the LTE & GPS Antennas
Note: 1. Use the plastic red caps to cover unused antenna ports
2. GPS and 3G/4G-LTE antenna(s) sold separately
Screw the male SMA
3G/4G-LTE and/or GPS
antennas tight to the
female connectors.
Connect to the MAIN port,
the primary cellular antenna
port to transmit and
receive signal, if decide to
use a single LTE antenna.
Do not over-torque the antenna on the connector.
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
6Access to the MX-1000(e)
Access to the MX-1000(e) Web interface by entering
http://192.168.1.254 in the address bar of the web browser.
Default Login Information: Username (admin) and Password
(A unique12-digit password can be found on the device label).
The Quick Start Wizard provides key steps to connect the
MX-1000(e) to the Internet.
MINI
USB2 MINI USB1
Connect to Mini USB Ports
Note: Software programming tool is required for the Mini USB interface
Connect to Mini USB port(s)
for direct connection to the
Cellular module(s) for
management – debug,
change firmware, and
configuration.
4
PIN
1
2
3
4
Ground
Ground
ACC
VCC
Black
Black
White
Red
-
-
Input
10~56VDC
Denition Details Wire color
4
21
3
5Connect to Power Source
Use the DC Power Adapter
Attach the power cable
with 4-pin miniFIT to
DC jack power cable
the MX-1000(e) and plug
in the supplied DC
power adapter.
Use Vehicle Electrical System (Power & Ignition Sensing)
Attach the Vehicle power cable to
the MX-1000(e) and connect the
wire leads of the power cable to
vehicle’s electrical system.
BLACK Wire (PIN 1 & 2):
Ground (GND). Use one
of the BLACK wires for
a neutral or ground
connection
WHITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be
connecting into vehicle accessory wire.
RED Wire (PIN 4): VCC/OFF Voltage wire to the battery.
DC power range from 0V to 56V.
Battery
POWER
GND Ignition Switch
Fuse
ACC
VCC
POWER

Gigabit RJ-45
Ethernet LAN Port
Gigabit RJ-45
Ethernet LAN/WAN Port
1Power - Green: System ready
Red: Boot failure
2Internet - Green: IP traffic via WAN
Red: WAN IP request failed
Off: No WAN Connection or in Bridge Mode
5WAN 1/2 -
(Cellular
Signal
Strength
Indicator)
3USB 1/2 - Green: Connected with an external storage device
4GPS - Green: GPS is active
Green: RSSI greater than -69 dBm. Excellent signal condition
Green flashing quickly: RSSI from -81 to -69 dBm. Good signal condition
Orange flashing quickly: RSSI less than -99 dBm. Poor signal condition
Orange flashing slowly: RSSI less than -99 dBm. Poor signal condition
Orange: No signal and the 4G LTE module is in service
Off: No LTE module or LTE module fails
6Gigabit Ethernet -
(LAN 1-4)
Green: Transmission speed is at Gigabit speed (1000Mbps)
Orange: Transmission speed is at 10/100Mbps
Blinking: Data being transmitted/received
Green: Wireless connection established
Green blinking: Data being transmitted / received
Orange: WPS configuration is in progress
7WI-FI &WPS -
USB 2.0 Host Ports
(External Storage)
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
LTE #1 (Main Antenna)
SMA Female Connector
GPS Antenna
SMA Female Connector
LTE #2 (Auxiliary Antenna)
SMA Female Connector
LTE #1 (Auxiliary Antenna)
SMA Female Connector
LTE #2 (Main Antenna)
SMA Female Connector
4-pin Power/Ignition Connector
(Input power 10-56V DC range)
123 4 5
6
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
Wi-Fi Female RP-SMA
Antenna Connector
SIM Card Slots
(Dual SIM Dual Module)
MINI USB
(LTE Module Management)
Reset
Wi-Fi On/OFF
& WPS
7
DEVICE OVERVIEW & LEDS
Use the DC Power Adapter
Attach the power cable
with 4-pin miniFIT to
DC jack power cable
the MX-1000(e) and plug
in the supplied DC
power adapter.

Attach and fasten the Mounting Bracket (known as bracket
plate) to the back or front of the MX-1000(e) using four (4)
mounting screws included in the package.
1. MX-1000(e) 2. Mounting Bracket 3. Mounting Screws
MOUNTING THE ROUTER
MOUNTING BRACKET CONTAINS: Bracket plate and Eight (8) Mounting Screws
The Bracket plate is designed to securely attach and mount the MX-1000(e) on any flat surface – including desktop, table,
chassis, etc.
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
1
2
3
3
3
3
Side Views
1
1
1
1
Mount the MX-1000(e) to a flat surface by drilling the four (4)
mounting screws through the bracket plate holes.
1. Bracket Holes
POLICE
V3.1