Becker Traffic Pro High Speed 7820 User manual

Navigation CD 3.X
Subject to errors and technical modifications 13 Copyright by Becker GmbH, D-76303 Karlsbad
If you received this operation guide update when purchasing
a new unit, the functions and modifications described from
page 14 are intended as a supplement to your operation guide.
If you received this operation guide update together with an
update CD, the update procedure and the new functions and
modifications are described on the following pages.
Installation of CD 3.X
In order to install CD 3.X, remove the old CD and insert the
new CD 3.X.
After a short time, the following display or a similar display
appears.
Using the right rotary control select , "! and press to
confirm.
The navigation and radio software is updated.
A progress bar appears on the display.
During updating, the ignition should be switched on and the
vehicle should not be moved.
Note on update for 7825 (blue display)
After starting an update, the display illumination is switched
off during installation. During this period , the unit should not
be operated. The switching off of the illumination does not
constitute a fault. After installation of the radio software, the
illumination is switched on and the unit is switched to radio
mode. Installation of the navigation software continues in the
background. Navigation mode can only be selected after com-
pletion of navigation software installation.
VOVV
!



Navigation CD 3.X
Subject to errors and technical modifications 14 Copyright by Becker GmbH, D-76303 Karlsbad
Modifications to navigation mode
The following modifications have been made to navigation
mode or the following new functions have been added.
• Navigation CDs
• Destination input via coordinates
• Switching the speed limits display on/off
• Dynamic navigation with TMC
Navigation CDs
Two navigation CDs are supplied with the navigation unit.
These CDs contain a digitised street map. One CD for North-
ern Europe (CD no. 1) and one CD for Southern Europe (CD
no. 2) are supplied.
The complete trunk road network and all destination centres
in the digitised area of Northern and Southern Europe are
available on the CDs.
All digitised roads of the northern countries are also included
on the Northern Europe CD. All digitised roads of the south-
ern countries are also included on the Southern Europe CD.
In these detailed areas of the Northern or Southern Europe CD
road map, motorways, regional roads and unclassified roads
as well as country roads are stored. Larger cities and commu-
nities are comprehensively covered. For smaller towns and
communities, the regional and unclassified roads or access
roads and the town centres are included.
One-way streets, pedestrian zones, turning bans and other
traffic regulations are taken into account as far as possible.
There may be discrepancies between the data on the naviga-
tion CD and the actual local situation, due to permanent
changes to road systems and their traffic regulations.

Navigation CD 3.X
Subject to errors and technical modifications 15 Copyright by Becker GmbH, D-76303 Karlsbad
Navigation with two European CDs For example, if you wish to navigate from a town on the
Southern Europe CD (D) to a town on the Northern Europe
CD (B), enter your destination address as usual. After enter-
ing the town, you will be prompted to insert navigation CD
No. 1 by the display   !#. After in-
serting the relevant CD, enter the road and, if required, the
house number or the town centre.
The required map data is loaded and stored internally after
route calculation has started.
Note: For Norway, Sweden, Finland and Denmark, non-
verified data has been used to achieve a high depth of
digitisation; i.e. with this data, the navigation system
cannot refer to information such as motorway, trunk
road, 30 zone, one-way street or other traffic regula-
tions, as this is not recorded.
All roads can be used, but optimum route guidance
cannot be guaranteed.
AArea of Northern Europe CD with all digitised roads.
BFor example, a town or an address in
Germany (on the
Northern Europe CD).
CArea of Southern Europe CD with all digitised roads.
DFor example, a town or an address in France (on the
Southern Europe CD).
A
B
C
D

Navigation CD 3.X
Subject to errors and technical modifications 16 Copyright by Becker GmbH, D-76303 Karlsbad
Destination input via coordinates
If the geographical coordinates (latitude and longitude) of a
destination are known, these can be entered and route
guidance to the destination started.
To enter the coordinates of the destination, select
! by turning the right-hand rotary control .
Press to confirm the selection.
Enter the latitude of the destination using the right-hand
rotary control . Entries must be made in degrees, minutes,
seconds and a direction as the crow flies, e.g. 11°38’34[[ N.
To confirm the entry, press and hold the right-hand rotary
control for more than 2 seconds. To confirm, the small
tick can also be selected and the right-hand rotary
control pressed briefly.
Enter the longitude of the destination using the right-hand ro-
tary control as described above.
To confirm the entry, press and hold the right-hand rotary
control for more than 2 seconds. To confirm, the small
tick can also be selected and the right-hand rotary
control pressed briefly.
Note: If the coordinates entered are located beyond the
boundaries of the digital map, a message will
appear notifying you of this. The system cannot
navigate to a position beyond the boundaries of
the digital map.
The navigation system will now prompt you to enter a name
for the coordinates entered.
Enter a name as described in the main instructions under
"Entering a destination in the destination memory".
The program then switches to the Route menu.
Route guidance can now start.
 !

&
!!"P
YYYYYYYYYYYYYYYYYYYYYYYYYYY
YYY YYYYYY
LONGITUDEP
YYYYYYYYYYYYYYYYYYYYYYYYYYY
YYY YYYYYY

Navigation CD 3.X
Subject to errors and technical modifications 17 Copyright by Becker GmbH, D-76303 Karlsbad
Switching the speed limits display on/off
If the speed limits display is ON, the system will inform you
of the maximum permissible speed limit for the route along
which you are travelling during route guidance, insofar as this
information is available.
Set and confirm ! in the System Settings menu.
By pressing the right rotary control selection can be made
between speed limits display  or .
Setting is confirmed and accepted by pressing and holding
the right rotary control .
If, when the speed limit display is ON, you travel along a
route with a speed limit and this speed limit is stored on the
navigation CD, the corresponding symbol will appear on the
right-hand side of the display indicating the speed limit.
The distance to the next point at which for example a turn
should be made is displayed below the navigation arrow,
which appears in reduced format.
On routes with variable speed limits (dependent on weather
conditions, time of day etc.) a symbol with the text @5Y or a
speed with an underscore (e.g.: "80") draws the driver’s atten-
tion to the fact that the speed limit is variable.
Note: As temporary speed limits (e.g. due to road works)
are usually short-lived, these have not been included
on the CD.
Warning
Accident hazard
Road traffic regulations always take priority when a vehicle
is being driven in traffic. Road signs en-route should always
be heeded. In some cases, the speed limit indicated by the
navigation system may be incorrect. At all times, the driver
must decide whether or not to heed the speed limit indicated.
We do not accept liability for erroneous data provided by the
navigation system.
G
!"!

!!
! F
T
PY
TV

Navigation CD 3.X
Subject to errors and technical modifications 18 Copyright by Becker GmbH, D-76303 Karlsbad
Dynamic navigation with TMC
Note: Dynamic route guidance is not possible in all coun-
tries.
To use dynamic navigation and the functions de-
scribed below, TMC must be switched on, as de-
scribed under “Switching TMC on/off” on page 22.
When any route recalculations are made with active
dynamic route guidance, the navigation system may
request the Navigation CD (if the Navigation CD is
not already inserted).
Austria: The location and event code was made
available by ASFINAG and BMVIT.
What is dynamic route guidance?
Dynamic route guidance is used to calculate the route, taking
current traffic announcements into account.
The traffic announcements are transmitted by a TMC radio
station in addition to the radio programme and are received
and analysed by the navigation system. There is no charge for
receiving traffic announcements.
Note: Traffic announcements are transmitted by radio sta-
tions, therefore we cannot accept any responsibility
for the completeness and correctness of the an-
nouncements
Activating dynamic route guidance
Dynamic route guidance can be started by selecting
!!S&YY in the route menu.
Note: Can only be selected if TMC has been switched on or
is currently switched on. See “Switching TMC on/
off” on page 22.
If !!S&Y Y is not displayed immediately (display
!!S ! Y or !!S ! Y), then &
"! must be selected by entering the route settings.
# !!
DFF
" Y

Navigation CD 3.X
Subject to errors and technical modifications 19 Copyright by Becker GmbH, D-76303 Karlsbad
Dynamic route guidance is started after confirmation of &
 "! using the right rotary control and subse-
quent confirmation of !!S&YY.
Note: If dynamic route guidance has been activated, the
routes are calculated using the "fast route" setting.
If dynamic route guidance has been activated, a continuous
check is made for the presence of relevant announcements for
the selected route. The route is then calculated using the "fast
route" option, while taking into account current traffic an-
nouncements. If the check determines that a traffic announce-
ment is relevant for the route guidance, then a new route to the
destination is calculated automatically by the unit.
$"! appears on the display. In addition, there is a voice
announcement "The route is being recalculated due to cur-
rent traffic announcements". is displayed inversely.
Note: If no TMC station was found, then !!
 ! !   !   is
displayed. After a short time, the unit switches back
to the route guidance display.
If a TMC station still cannot be found after
10 minutes, !!!
!  !   is displayed, ac-
companied by a brief signal tone.
Your navigation system can receive TMC information, wheth-
er a TMC station is selected or not. However, in order to guar-
antee optimal reception of TMC information, we recommend
the selection of a TMC station.
!"!

 !"!

Navigation CD 3.X
Subject to errors and technical modifications 20 Copyright by Becker GmbH, D-76303 Karlsbad
Modifications to radio mode
The following modifications have been made to radio mode:
• Modified operation in radio mode (TrafficProgramme)
• Switching TMC on/off
• Display for TMC stations
Traffic Programme (TP)
If an RDS diversity transmitter transmits TP announcements,
it is possible to interrupt CD, CDC/AUX, MW, LW or SW
operation or the mute function and to switch through the
transmitted TP announcement. Moreover, you can listen to
one FM station while having TP announcements switched
through that are transmitted by another FM station.
The functionality of the traffic programme functions depends
on the status of the TMC setting - TMC switched on/off
(“Switching TMC on/off” on page 22)
When TMC is switched off:
• There are two ways to select a TP transmitter:
- automatic tracking
- direct programming
Automatic tracking always uses the FM station currently
being received as the TP transmitter. If the selected FM
station has poor reception quality or cannot function as a
TP transmitter, the unit applies specified criteria to search
for a new TP transmitter.
Direct programming enables a TP transmitter to be pro-
grammed that is not the FM station being received. For ex-
ample, one FM station can be received while TP
announcements transmitted by another FM station are
switched through.
If the programmed TP transmitter reception is poor, the
unit switches to automatic tracking until the programmed
TP transmitter is receivable.
When TMC is switched on:
• With TMC, the unit is capable of selecting a suitable traf-
fic programme transmitter automatically. If possible, a
TMC station is selected as the traffic programme transmit-
ter. The selected TMC station usually offers the best traf-
fic information for the region in which you are travelling.
If no TMC station is available, the traffic programme
transmitter with the strongest signal is selected.
If an RDS transmitter is equipped with a traffic programme,
this is indicated on the display by !.
An inverse TP appears on the display to indicate that the
traffic programme is active.

Navigation CD 3.X
Subject to errors and technical modifications 21 Copyright by Becker GmbH, D-76303 Karlsbad
Activating/quitting the TP menu
Activating: Press the button (traffic announcements can-
not be transmitted).
Press the multifunction button.
Quitting: Press the button or the TP menu will be auto-
matically terminated after 8 seconds without actuation.
Switching TP on/off
In all modes and wavebands, TP can be switched on/off by
pressing the button for more than 2 seconds.
TP can also be switched on/off in the TP - menu.
Switching on: To switch on TP in the TP menu, press
the multifunction button repeatedly until !65 is dis-
played.
Switching off: To switch off TP in the TP menu, press the
multifunction button repeatedly until ! 6-- is dis-
played.
TP is switched off after returning to normal display.
Selecting automatic tracking
Only applies when TMC is switched off.
In all modes and wavebands, automatic tracking can be
switched on by pressing the button for more than
2 seconds.
To switch on automatic tracking in the TP menu, press the
multifunction button repeatedly until ! 65 is dis-
played.
Attention: If a TP transmitter has already been pro-
grammed directly, it will once again be select-
ed as the TP transmitter.
73
,+
!7 ;( #63 !4*
!7
73
73
!7
,+
!7 ;( #63 !4*
!7
!7 ;( #63 !4*
,##
73
!7
,+
!7 ;( #63 !4*

Navigation CD 3.X
Subject to errors and technical modifications 22 Copyright by Becker GmbH, D-76303 Karlsbad
Selecting / deleting direct programming
Only applies whenTMC is switched off.
Activate the TP menu.
Selecting: Press the multifunction button.
Using the right rotary control , select the desired TP trans-
mitter. After a short delay and without actuation, the selected
transmitter is accepted.
Deleting: Press the multifunction button.
Using the right rotary control , select <;6:,3,*; and
press to confirm. After a short delay and without actuation,
the direct programming is deleted.
Quit the TP menu.
Switching TMC on/off
Note: You can find further information on TMC under
“Dynamic navigation with TMC” on page 18.
Activate the TP menu.
Switching on:
Press the multifunction button repeatedly until !
65 is displayed.
If TMC is switched on, a traffic programme transmitter can-
not be selected freely. A TMC station is selected by the unit,
provided one can be received. This transmitter then corre-
sponds to the traffic programme transmitter.
Switching off:
Press the multifunction button repeatedly until !
6-- is displayed.
If TMC is switched off, a traffic programme transmitter can
be selected freely.
Note: Dynamic navigation functions (dynamic route, traf-
fic information) cannot be selected or called up.
;(
11E $
!7 ;( #63 !4*
;(
11E<;6:,3,*;
!7 ;( #63 !4*
,+
!7 ;( #63 !4*
!4*
!4*

Navigation CD 3.X
Subject to errors and technical modifications 23 Copyright by Becker GmbH, D-76303 Karlsbad
Display for TMC stations
If a radio station transmits TMC information in addition to the
radio programme, this is indicated on the display by the ab-
breviation !. TMC information is received and analysed
by the navigation system. The reception of traffic announce-
ments is free of charge.
TMC is shown in normal typeface:
The instantaneously selected station is a TMC station. TMC
is switched off.
TMC is shown in inverted typeface:
The instantaneously selected station is a TMC station. TMC
is switched on.
OY MOT

P
5;+; ,. 79 >9 SM
!
OY MOT

P
5;+; ,. 79 >9 SM
!