Bedsure BS-LV0A User manual

HEATED THROW
USER MANUAL
MODEL #BS-LV0A

1
BS-LV0A
Heating Blanket - Tie Dyed
DC 24V
65W Max
1 Hour/2 Hours/3 Hours/4 Hours
100% Polyester
127cmX152cm/50X60 inches
PRODUCTS AND ACCESSORIES
Throw
Power Adapter
PRODUCT SPECIFICATIONS
Model
Name
Input Voltage
Rated Power
Time Setting
Materials
Product Dimensions

IMPORTANT SAFETY
INSTRUCTIONS
-DO NOT DESTORY
a) Be sure to read carefully the accompanying instruction
booklet before using this bedding” .
b) Do not use this bedding with an infant, an immobile
person, or anyone insensitive to heat, such as a person
with poor blood circulation” .
c) Do not tuck in the wired area of this bedding” .
d) Do not route electrical cords between the mattress and
box spring. Do not allow the cords to be pinched” .
e) Keep the control away from drafty areas that may
become damp or wet such as an open window.
2

f)Donot use pins–They maydamage the electric wiring”.
g) Be sure that this bedding is used on an
alternating-current supply circuit of the proper voltage”.
i) Excessive heating may result from folding bedding,
other than a mattress, when in actual use”.
j) If improper operation of this bedding is observed,
discontinue its use immediately and consult the
manufacturer or the dealer regarding its repair”.
k) “For throw blankets only: Do not use with rocking
chairs, recliners, chairs with casters or wheels, or other
furniture subject to movement.”
l) “Do not tuck the blanket or supply cord in a sofa or other
furniture. All portions of the blanket or controller should
be visible at all times.
m) “Wrapping of cord around the controller may damage
the cord. Loop loosely when storing.”
3

BEFORE EACH USE, ALWAYS INSPECT THE PRODUCT TO
ENSURE THAT THERE IS NO DAMAGE TO THE POWER
CORD, THE CONTROLLER, ORTHE THROW.
SET UP GUIDE FOR HEATED THROW
AUTO-SHUT-OFF FEATURE
setting is reached.
A Friendly Reminder
Please disconnect all cords if you do not plan on using the product for
an extended period of time.
2. Keep the controller in a ventilated area, and do not cover it with any
objects to prevent overheating.
3. The timer duration range is 4 settings: 1H-2H-3H-4H
4. The heat level range is 4 settings.
4

CAUTION:
Never PLUG the adapter
before connect the cord.
CAUTION:
Never PLUG the adapter
before connect the cord.
HOWTO USE CONTROLLER
Anomaly Alert
1. If the controller is connected to the power line port, and then
connected to the blanket coupler will cause the controller lights
flashing alarm. At this time, please long press the ON/OFF button
until the end of the flashing.
2. Please connect the controller to the blanket coupler first and then
turn on the power.
Instructions
2. ON/OFF button is heating level button and time setting button.
1. Please connect the controller to the electric blanket coupler first, then
connect to the power. The controller's halo will keep lighting for a few seconds
then turn o, it means the product is proceeding self-check and it's OK.
3. Press the button in the middle of the controller, the product will
default to the warm heating level when turned on, then each time
press the button, a heating level (Warm-Low-Med-High) will be added.
After no operation for 20 seconds, the light on the controller(except
timing light) will automatically go out.
4. Press and hold the middle button of the controller for 2 seconds to
switch to the time setting mode. The product defaults to 4H time
setting whenturned on. Each time you press thebutton, it changes a
timing level(1H-2H-3H-4H). if there is no operation after 2 seconds,
the timing will be automatically confirmed, and thetiming light will
always be on until the timing expires.
5. When the timer expires, the heating level light goes out and thetime
setting light flashes. If you continue to use it,please press the ON/OFF
button again to enter the heating working state.
1
2
4
3
5

TROUBLESHOOTING
NUMBER
1
2
3
PROBLEM
Not Heat
/ No Power
‘High’Heat
Setting
Indicator is
Flashing
Throw/Blanket
Has aHot Spot
SOLUTION
-Verify if AC outlet is functional.
-Check for physical damage to
the cord, controller or threw. If
there is damage, discontinue use.
-If failure continues,
discontinue use.
The'High' Heat Setting Indicator
light will start flashing when a
fault is detected. Follow these
steps to reset the controller:
1 - Unplug the controllerfrom the
AC outlet
2 - Verify that the AC outlet is
functional and plug the controller
into the AC outlet again.
3 - Press the Heat Control Button
until the desired setting is
reached.
Check to make sure that the
throw/blanket is not folded,
bunched, crushed, or
overlapping in any areas.
SYMBOL EXPLANATION
6

CAREAND CLEANING INSTRUCTIONS
CAUTION:Do not dry clean. Do not use bleach. Do not use wringer. Do
not iron. Do not immerse control or Cord in water or other liquids. Do
not use mothballs or sprays of any kind. Do not reconnect the heated
product until it is completely dry.
Before Washing or Storing Your Heated Product
1. Disconnect power cord from wall BEFORE detaching controller cord
from the heated throw.
2. Ensure that no cord is still connected and none of the wires have
worn through the fabric.
3. Carefully follow all washing instructions or your heated throw may
shrink and possibly cause a fire hazard. Store as any other blanket,
folded in a dry place.
Washing Instructions
1. Machine wash in cold water; gentle cycle or hand wash.
Caution: Do not use commercial dryers or the dryers at your local
laundromat They got too hot and would damage the wiring of the
heated product
2. Tumble dry low, delicate cycle. Ensure that your heated product has
enough room to tumble freely.
3. Remove the heated product while still damp and gently stretch to its
original size.
4. Drape theheated product over a clothesline or a shower rod. DO
NOT use clothes pins.
5. Heated product must be COMPLETELY dry before reconnecting the
power plug or control plug.
Hang to Dry
1. While still damp, gentlestretch the heated product back toits original size
2 Drape theheated product over a clothes line or hang over a shower
rod. DO NOT use clothespins.
3. Heated product must be COMPLETELY dry before reconnecting the
power plug or control plug.
7

-
from the wall socket
- Wrapping of the cord around the controllers may damage the cord.
Loop loosely when storing.
- Never iron your heated product
- Never use dry cleaning fluid onthe heated product, cleaning solvents
may damage the wiring insulation.
FCC Notification:This equipment has been tested and found com ply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which canbe determined by turning the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver
which the receiver is connected;
• Consult the dealer or an experienced radio/TV technican for help
In accordance with the rules and regulations of the FCC, changes or
modifications to this equipment,not expressly approved in writing by the
party responsible for compliance could void the user* s authority to
operate this equipment
SAFETY ESSENTIALS:
CARE AND MAINTENANCE
8

All heated products carry a five-year, limited warranty. The limited
warranty is valid only for, and not transferable from, the original retail
purchaser or gift recipient. No limited warranty service is available
without proof of purchase or valid gift receipt from an authorized
retailer:
Bedshe International Business Co., Ltd (Warrantor), as its option, will
replace this product or any component of the product found to be
defective in materials or workmanship during the limited warranty
period, subject to the exclusions and limitations set forth herein.
Replacement will be made witha new or remanufactured product or
component. If the product is no longer available, replacement may be
made witha similar product of equal or greater value. This is your
exclusive limited warranty.
This limited warranty is valid for the original retail purchase or gift
recipient from the date of initial purchase and is not transferable to any
subsequent purchaser. Proof of purchase is required to obtain warranty
performance. Keep the original sales receipt. Dealers, service centers,
retail stores and online retailers do not have the right to alter; modify, or
any way change the terms and conditions of this limited warranty.
This limited warranty does not cover normal wear of parts ordamage
resulting from any of the following: negligent use, misuse, or abuse of
the product; accident; neglect; use on improper voltage or current; use
contrary to the operating instructions; disassembly; parts or
components not supplied by the Warrantor; parts or components that
have been modified; or repairs or alterations contrary to the operating
instructions. Further; the limited warranty does not cover damage
caused by Acts of God or Nature, such as fire, flood, hurricanes and
tornadoes.
WARRANTY
9