Behringer ULTRA-DI DI400P User manual

BEHRINGER ULTRA-DI DI400P
Thank you for showing confidence in BEHRINGER products by purchasing the ULTRA DI DI400P.
The DI400P is a high performance passive direct injection box.
+Please read the safety instructions that appear at the end of this document.
Being on stage or in the studio, musicians often look for ways to connect certain signal sources
directly to the mixing console. Even though this approach has obvious advantages, there are still
some technical hurdles obstructing its implementation. For example, keyboards seldom feature
balanced outputs, and guitars can not be directly connected to mixing consoles because of the
high impedance of guitar signals.
The DI400P lets you directly tap into a high impedance, unbalanced signalfor example, the signal
between a guitar and a guitar amp. From there on, you can feed the signal directly to a mixing console.
1. CONTROL ELEMENTS AND CONNECTIONS
Fig. 1: Top view
+ PARALLEL IN/OUT (¼" TS): These connectors are used for connecting unbalanced
signal sources. Because both connectors are wired in parallel, they can be used both as
an input and as a direct output to loop the signal through to a monitor amplifier.
OUTPUT (XLR): This is the balanced mic level output. Use a high quality balanced microphone
cable to establish connection.
Using the GND LIFT (ground lift) switch, you can fully separate input and output grounding.
Depending on how the equipment to which your DI400P is connected is grounded, using
the GND LIFT switch lets you lower hum noise or ground loops. When the GND LIFT switch
is in LIFT position, the ground connection is interrupted.
The SERIAL NUMBER of the DI400P is located at the bottom.
2. CONNECTING AN INSTRUMENT SIGNAL
Fig. 2: Guit r ß DI-box ß guit r mp/mixer
This illustration shows the application of a DI box. The signal feeding the amplifier remains
unchanged; it is simply taken and routed into the amp. The low impedance balanced signal is
forwarded to the mic input of the mixing console. This application has its advantages particularly
with bass guitars, because very few microphones can linearly transmit bass frequencies with
high signal levels. If you are using effects, insert the DI400P after the effects device, so that you
can monitor the effects via the PA system or the recording as well.

BEHRINGER ULTRA-DI DI400P
3. SPECIFICATIONS
Frequency response 40 Hz ( 3 dB) to 20 kHz
THD+N (distortion) 0.007% @ 1 kHz, input level +4 dBu
INPUT ¼" TS (unbalanced)
Level change (input ß output) 20 dB
OUTPUT Balanced XLR
Impedance ratio (input ß output) 110 : 1
Dimensions (H x W x D) 1.4" x 4.7" x 2.6" (35 mm x 120 mm x 66 mm)
Weight approx. 0.44 lbs
(0.2 kg)
BEHRINGER continuously strives to assure the highest quality standards possible. Required modifications
may be implemented without prior notice. echnical data and the appearance of the unit may deviate from
the above values and/or illustrations.
4. WARRANTY
For our current warranty terms, please refer to our website at http://www.behringer.com
echnical specifications and appearance subject to change without notice. he information contained
herein is correct at the time of printing. he names of companies, institutions or publications pictured or
mentioned and their respective logos are registered trademarks of their respective owners. heir use
neither constitutes a claim of the trademarks by BEHRINGER® nor affiliation of the trademark owners with
BEHRINGER®. BEHRINGER® accepts no liability for any loss which may be suffered by any person who
relies either wholly or in part upon any description, photograph or statement contained herein. Colours and
specification may vary slightly from product. Products are sold through our authorised dealers only.
Distributors and dealers are not agents of BEHRINGER® and have absolutely no authority to bind
BEHRINGER® by any express or implied undertaking or representation. No part of this manual may be
reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying
and recording of any kind, for any purpose, without the express written permission of BEHRINGER
Spezielle Studiotechnik GmbH. BEHRINGER® is a registered trademark.
ALL RIGH S RESERVED © 2006 BEHRINGER Spezielle Studiotechnik GmbH,
Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.
el. [phone], Fax [phone]
SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Install in accordance with the manufacturers instructions.
8) Only use attachments/accessories specified by the manufacturer.
9) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way.