Belco Security DA3000 User manual

DA3000 Standalone Touch Access Controller
User Manual v2.0
1. Specifications:
1.1 Technical parameters：
NO
Item
Value
1
Operating voltage
DC 12V±10%
2
Operating current
< 100mA
3
Dimensions
120mm×78mm×22mm
4
Weight
110g
5
Ambient temperature
0℃—60℃
6
Relative humidity
20%—80%
7
Storage
1000 users
8
Card type
RFID (Mifare optional)
9
Card reading distance
1－10CM
1.2 Factory Default：
1.3 Light and Sound indicates:
Light: red and green
Light Description
Access control status
Red light flash every 1 sec（Slow flash）
Holding state
Red light is always ON
Programming state
Green light is always ON within Open time
Unlocking state
Green light flash every 0.5sec (Fast flash)
Pending further action
Sound：buzz
Description
Indicates
1 short buzz
Valid input
3 short buzz
Invalid input
1 long buzz
Program success
Continuous long buzz
Restoring factory programming passwords
2. Installation Guide:
JP1 terminal：
JP2 terminal：
NO
Mark
Color
Function
Remark
1
+12V
Red
Power+
Optional
2
GND
Black
Power-
3
DATA0
Green
WG DATA0
4
DATA1
White
WG DATA1
5
NC
Brown
Relay NC output
6
COM
Blue
Relay Com output
7
NO
Purple
Relay NO output
NO
Mark
Color
Function
1
+12V
Red
Power+
2
GND
Black
Power-
3
PUSH
Blue
Low level output
4
OPEN
Yellow
Door Release
5
BELL
Grey
Bell
6
BELL
White
Bell
Programming
Password
123456
Common Access
Password
None
Backlight
Auto
Relay Unlock
output
5 Seconds
W26 port
Input
Security mode
OFF
Open mode
Card or Access Password
Access Password include Private Access Password (PIN) and
Common Access Password

3. Programming Guide
3.1 Detailed Programming Guide：
3.2 To reset to Factory Programming Password（123456）
Step1、Turn off power and connect bin 2&3 of RST(S1)。
Step2、Turn on power and buzzer gives 3 long buzz with green light flash fast。
If need to set Manager Card, now read two empty cards first one as Manager Add Card and
Second one as Manager Delete Card with red light flashing and continuous short buzz .
Step3、Turn off power, disconnect bin2&3 and connect bin 1&2 of RST。
Step4、Turn on power again.
3.3 How to use Manager Card –MAC&MDC
To add a card user in standby mode: read MAC read new cards read MAC
To delete a card user in standby mode: read MDC read registered cards read MDC
To delete all users in standby mode: read MDC read MAC read MDC
Remark: User cards can be added or deleted continuously.
3.4 User ID No. explain
User ID is auto-generating 4-digit number started at 0001. The number increases with adding
user one by one and ignores deleting user. Common Access Password has no ID.
3.5 How to change PIN (When open mode: card+ PIN)
After reading card and input corresponding PIN to open the door, within 5 seconds, long press #
until the green lights flash fast. and then input new PIN # new PIN # , new PIN
changed successfully with a long buzz.
Purpose
Operation
Remark
Basic
Function
Change Programming Password
#Programming Password #0new Programming Password #
New Programming Password #
If Programming Password lost, perform 3.2 to reset to Factory Default (123456).
Add user card
#Programming Password #1read card #
If add multiple cards, read cards continuously
Set Common Access Password
#Programming Password #21 new Common Access Password #
Can only enroll one Common Access Password. Open method: Password #
Delete all users
#Programming Password #40 0000 #
Delete all cards and PIN except Common Access Password
Delete user by read card
#Programming Password #41 read card #
If delete multi cards, read cards continuously
Advance
Function
Add Private Access Password(PIN)
#Programming Password #22 PIN #
Can enroll more than 1 PIN, Unlock door method: PIN #
Add card by input card No.
#Programming Password #23 input card No. #
Card No. is 10-digit or 8-digit, machine auto-identify
Add multi-card by input card No. zone
#Programming Password #24 input start card No. card Qty #
Card Qty is 4-digit (If one-time add twenty cards, input 0020)
Add “card +PIN”
#Programming Password #3read card PIN #
If modify PIN, see 3.5
Delete user by input User ID No.
#Programming Password #42 input User ID No. #
About User ID No. see 3.4
Delete user by input card No.
#Programming Password #43 input card No. #
Card No. is 10-digit or 8-digit, machine auto-identify
Delete user by input PIN
#Programming Password #44 input PIN #
PIN is 3~6 digits.
Delete all PIN users
#Programming Password #45 1111 #
Use to delete PIN users (Do not include Card users and Card +PIN users)
Change Open time
#Programming Password #5XX #
XX can be 2-digit, and the max. is 99. If input 00, the signal output time is 0.2 Secs.
Set Open mode
#Programming Password #6XX #
XX can be 01(only card)/ 02(card or Access Password)/ 03(card+PIN)
Reader setting (Optional)
#Programming Password #604 #
The machine can be used for reader(W26 output)
Security function Setting
Anti-dismantle Alarm setting (Optional)
#Programming Password #7XX #
XX can be 01/ 02( Security function OFF/ON) and 03/04(Anti-dismantle alarm OFF/ON)
Remark: Security Function ON means System would be locked for 5 Minutes if continue to read illegal card or input wrong Access Password for 10 times.
Backlight setting(Optional)
#Programming Password #8XX #
XX can be 01/02/03 (Normal ON / Normal OFF / Auto)
Reset Factory Default
#Programming Password #899 #
Except Programming Password and Manager Card
Set Manager Card
#Programming Password #91 read MAC read MDC #
First read card is Manager Add Card and Second read card is Manager Delete Card.
Programming Password Default: 123456, all password can be 3~6 digits