Belden Hirschmann BAT867-F User manual

Installation BAT867-F
Release 01 12/2019
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Industrial Access-Point / Client / Access-Bridge
BAT867-F

2019-12-18 Installation BAT867-F
Release 01 12/2019
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2019 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation BAT867-F
Release 01 12/2019 3
Contents
Safety instructions 5
About this manual 15
Key 16
1 Description 17
1.1 General description 17
1.2 Device name and product code 18
1.3 Device view 20
1.4 Power supply 20
1.4.1 Supply voltage with the characteristic value W
(24 V DC) 20
1.4.2 Supply voltage with the characteristic value P (Power
supply only through PoE) 21
1.5 Ethernet port 21
1.5.1 10/100/1000 Mbit/s PoE port 21
1.5.2 Pin assignments 22
1.6 Connections for antennas 23
1.7 Display elements 23
1.7.1 Device state 23
1.8 Reset button 24
2 Installation 25
2.1 Checking the package contents 25
2.2 Installing and grounding the device 25
2.2 Mounting the device 25
2.2.2 Grounding the device 26
2.3 Installing the antennas 27
2.4 Connecting the power supply 27
2.5 Operating the device 28
2.6 Connecting data cables 28
3 Making basic settings 30

4Installation BAT867-F
Release 01 12/2019
4 First login (Password change) 31
5 Obtain compliance for operation in the European
Union 32
6 Configuring the transmit power 35
7 Monitoring the ambient air temperature 37
8 Maintenance and service 38
9Disassembly 39
10 Technical data 40
10.1 General technical data 40
10.2 Dimension drawings 41
10.3 Radio technology 42
10.4 Roaming 42
10.5 Receiving sensitivity, transmit power and data rate 43
10.5.1 IEEE 802.11b 43
10.5.2 IEEE 802.11g 43
10.5.3 IEEE 802.11a 44
10.5.4 IEEE 802.11n 44
10.5.5 IEEE 802.11ac 46
10.6 EMC and immunity 47
10.7 Network range 48
10.8 Power consumption/power output 48
11 Scope of delivery, order numbers and
accessories 49
12 Underlying technical standards 51
A Further support 52

Installation BAT867-F
Release 01 12/2019 5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 40.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.

6Installation BAT867-F
Release 01 12/2019
Installation site requirements
Use the device only indoors.
Restricted access location:
The location is outside the operator access area.
The location is accessible to the service personnel even when the
device is switched on.
Indoor operator access area:
The location is accessible without tools.
The person responsible for the area has provided access for the
operator intentionally.
The operator knows of the access possibilities, regardless of whether
they need a tool.
Relevant for Europe:
Supply only 24 V DC to the device and use a fuse.
Regarding the properties of this fuse: See “General technical data”
on page 40.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
See “General technical data” on page 40.
Mount the device in the vertical position.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.

Installation BAT867-F
Release 01 12/2019 7
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
When installing antennas, observe the regulations of the country in
which you are operating the WLAN device with regard to the general
operating permission and the maximum emission levels.
Install and operate this equipment with a minimum distance of
19.7 inches (50 cm) between the antenna and your body.
Grounding the device
For the functional earth (FE), there is a separate functional earth screw on
top of the device. The functional earth is electrically connected to the
circuit ground and the metal housing of the device.
Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.

8Installation BAT867-F
Release 01 12/2019
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
The connected voltage complies with the requirements for a safety extra-low voltage
(SELV) or ES1 as per IEC/EN 62368-1.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
Table 1: Requirements for connecting electrical wires

Installation BAT867-F
Release 01 12/2019 9
Requirements for connecting the supply voltage
The supply voltage is connected to the device casing through protective
elements exclusively.
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the
device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (for example a
switch or a plug). This disconnecting device is clearly identified. So in the case of an
emergency, it is clear which disconnecting device belongs to which power supply
cable.
The power supply cable is suitable for the voltage, the current and the physical load.
Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm² (AWG20 up to
AWG18).
The cross-section of the ground conductor is the same size as or bigger than the
cross-section of the power supply cables.
The following requirements apply alternatively:
Alternative 1 The power supply complies with the requirements for a limited power
source (LPS) as per IEC/EN 60950-1 or IEC/EN 62368-1.
Alternative 2 Relevant for North America:
The power supply complies with the requirements according to
NEC Class 2.
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-
low voltage (SELV) or ES1 as per IEC/EN 62368-1.
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is also
located in the minus conductor.
Regarding the properties of this fuse:
See “Technical data” on page 40.
Table 2: Requirements for connecting the supply voltage

10 Installation BAT867-F
Release 01 12/2019
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU and 2015/863/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/53/EU (RED)
Directive of the European Parliament and of the council on the
harmonization of the laws of the Member States relating to the making
available on the market of radio equipment.
This product may be operated in all EU (European Union)
countries under the condition that it has been configured correctly.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be available to the relevant authorities at the following
address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com
The product can be used in residential areas (residential, commercial and
light-industrial environments) and in industrial areas.
Interference immunity: EN 61000-6-1
Emitted interference: EN 55032
Safety: EN 62368-1
You find more information on technical standards here:
“Underlying technical standards” on page 51
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

Installation BAT867-F
Release 01 12/2019 11
Notes for countries with the following country codes:
The RED compliance requires compliant operation of the device in the
5 GHz band channels. Compliant operation of the device is achieved
by an unchangeable determination of the country setting. To obtain
RED compliance, perform the work steps described in chapter “Obtain
compliance for operation in the European Union” on page 32.
AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IT LI
LT LU LV MT NL NO PL PT RO
RS SE SI SK TR UK

12 Installation BAT867-F
Release 01 12/2019
Notes for Germany (DE), Ireland (IE), and the United Kingdom (UK):
Operation in the 5.8 GHz band at a radiated power (EIRP) >25 mW is
subject to meeting the following conditions:
Germany (DE)
Frequency range: 5725 MHz to 5875 MHz
Condition: The usage of this band is restricted to commercial public
telecommunication services. Registration at the Federal Network
Agency is required.
Name and website of the competent authority:
Bundesnetzagentur
www.bundesnetzagentur.de
Ireland (IE)
Frequency range: 5725 MHz to 5875 MHz
Condition: Registration of operational base stations
Name and website of the competent authority:
Commission for Communications Regulation
www.comreg.ie
United Kingdom (UK):
Frequency range: 5725 MHz to 5850 MHz
Condition: Light-licensing regime
Name and website of the competent authority:
Ofcom
www.ofcom.org.uk
DE IE UK

Installation BAT867-F
Release 01 12/2019 13
FCC note
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
BAT867-F
U.S. Contact Information
Belden – St. Louis
1 N. Brentwood Blvd. 15th Floor
St. Louis, Missouri 63105, United States
Phone: [phone]
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reposition the receiver antenna or change the angle of the receiver
antenna.
Increase the separation between the device and the receiver.
Connect the device to a different power supply from that to which the
receiver is connected.
Consult a specialist retailer or an electronic systems engineer for help.
Changes or modifications not expressly approved by the holder of the
certificate could void the user’s authority to operate this equipment.
Note for the use in the USA and in Canada
The following section applies to BAT867-F variants with the characteristic
value US (USA/Canada) for country approvals which are labeled as
follows:
Contains Transmitter Module
FCC ID: TK4WLE600VX

14 Installation BAT867-F
Release
01
12/2019
IC: 7849A-WLE600VX
This equipment complies with FCC and IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. Install and operate this equipment with a minimum distance of 19.7 in (50 cm) (related to a 9 dBi
antenna) between the radiation source and your body.
The antenna used for this transmitter must not be co-located with any other transmitters within a host device, except
in accordance with FCC multi-transmitter product procedures.
This transmitter is restricted to indoor use only within the 5.15 to 5.25 GHz band to reduce potential for harmful
interference to co-channel mobile satellite systems.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.
The FCC approval is valid only in conjunction with the listed antennas. If other antennas are used, the approval
expires. The responsibility lies with the operator of the system. The required antenna impedance is 50 .
Recycling note
After usage, this device must be disposed of properly as electronic waste, in accordance with the current disposal
regulations of your county, state, and country.
Antenna(s) for operation with this
device:
Permitted band of operation
2.4 GHz band 5 GHz band
5180 ... 5240 MHz 5260 ... 5320 MHz 5500 ... 5720 MHz 5745 ... 5825 MHz
BAT-ANT-N-3AGN-IP67 Yes Yes Yes Yes Yes

Installation BAT867-F
Release 01 12/2019 15
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
Documentation mentioned in the “User Manual Installation” that is not
supplied with your device as a printout can be found as PDF files for
downloading on the Internet at: https://www.doc.hirschmann.com

16 Installation BAT867-F
Release 01 12/2019
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

Installation BAT867-F
Release 01 12/2019 17
1 Description
1.1 General description
The devices allow you to set up WLANs (Wireless Local Area Networks) in a
local network. In contrast to a conventional network connection through
copper cables and fiber optic cables, some of the communication is
performed by means of a radio link.
The devices allow you to install a new LAN or expand an existing LAN.
Thanks to their high level of flexibility, the BAT867-F device is suitable for a
wide range of applications. Anywhere that high bandwidths, stable operation
and network security is required, WLAN with these devices provides the ideal
solution.
The devices are dual-band industrial high-performance wireless LAN access
points or clients complying with IEEE 802.11a/b/g/n/ac. They provide a high
radio output with a bandwidth of up to 867 Mbit/s. The devices support MIMO
(Multiple Input Multiple Output) and Multipath. The bandwidth is increased by
using the multipath transmission by means of reflections. 2 antennas for
sending and receiving help ensure stable network coverage with few shadow
areas.
The device is designed for the special requirements of industrial automation.
The device meets the relevant industry standards, provides very high
operational reliability, even under extreme conditions, and also long-term
reliability and flexibility.
The device works without a fan.
The device complies with the degrees of protection IP65/67.
There are convenient options for managing the device. Manage your devices
via:
Web browser
SSH
Telnet
HiDiscovery (software for putting the device into operation)
Management software (for example Industrial HiVision, LANconfig/
LANmonitor)
The device provides you with a large range of functions, which the manuals
for the operating software inform you about. You can download these
manuals as PDF files from the Internet on the Hirschmann product pages
(http://www.doc.hirschmann.com).

18 Installation BAT867-F
Release 01 12/2019
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
Item Characteristic Character
istic value
Description
1 ... 8 Product BAT867-F IP65/67 housing
9 ... 10 Country approvals
Example:
Singapore
XX
Example:
SG
You can determine the current country
approvals using the configurator (https://
catalog.belden.com)
11 Slot 1 W WLAN module
12 Slot 2 9 Not assembled
13 Slot 3 9 Not assembled
14 Access point or client A Access Point
C Client
15 Supply voltage 1 W Rated voltage
24 V DC
with PoE support
P Power supply solely through PoE
16 Supply voltage 2 9 Not assembled
17 Approvals 1 9 No additional approvals
J Railway applications (trackside) as per
EN 50121-4
18 Approvals 2 9 No additional approvals
19 Mounting A Standard
20 ... 21 Ethernet port 1 T1 8-pin, “X”-coded M12 plug for 10/100/1000
Mbit/s PoE port
22 ... 23 Optional:
Ethernet port 2 or interface
99 Not assembled
24 Temperature range L +14 °F ... +140 °F (10 °C ... +60 °C)
T Extended
-40 °F ... +158 °F (-40 °C ... +70 °C)
E Extended with Conformal Coating
-40 °F ... +158 °F (-40 °C ... +70 °C)
25 Software option 1 9 Not present
26 Software option 2 9 Not present
27 Software option 3 9 Not present
Table 3: Device name and product code

Installation BAT867-F
Release 01 12/2019 19
28 Configuration Z Accessory package
9 Not present
29 Device model H Hirschmann standard
Item Characteristic Character
istic value
Description
Table 3: Device name and product code

20 Installation BAT867-F
Release 01 12/2019
1.3 Device view
1.4 Power supply
1.4.1 Supply voltage with the characteristic value W
(24 V DC)
Power supply via an 8-pin, “X”-coded M12 socket for PoE
port
Your device is a PD (powered device). PSE (power sourcing equipment)
connected via a twisted pair cable on the PoE PD port serves as the PoE
power supply voltage. The PoE power supply means that no separate
power supply is required for your device.
1 Antenna connection 2
2 Antenna connection 1
3 LED display elements
4 Functional earth screw
5 Reset button behind a screwable IP65/67 protection cap
6 Applies to device variants featuring supply voltage with characteristic value W
(24 V DC):
5-pin, “A”-coded M12 socket
7 8-pin, “X”-coded M12 plug for 10/100/1000 Mbit/s PoE port
12
3
4
5
6
7