Belden Hirschmann BAT867-R User manual

Installation BAT867-R
Release 10 09/2021
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Industrial Access-Point / Client / Access-Bridge
BAT867-R

16.09.2021 Installation BAT867-R
Release 10 09/2021
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2021 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at:
https://www.doc.hirschmann.com
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation BAT867-R
Release 10 09/2021 3
Contents
Important information 5
Safety instructions 7
About this manual 20
Key 21
1 Description 22
1.1 General description 22
1.2 Device name and product code 23
1.3 Device view 24
1.4 Power supply 25
1.5 10/100/1000 Mbit/s twisted pair port 25
1.5.1 Pin assignments 26
1.6 Connections for antennas 27
1.7 Display elements 27
1.7.1 Device state 27
1.8 Reset button 28
2 Installation 29
2.1 Checking the package contents 29
2.2 Installing and grounding the device 29
2.2.1 Installing the device onto the DIN rail 29
2.2.2 Grounding the device 30
2.3 Installing the antennas 31
2.4 Connecting the terminal blocks 31
2.5 Operating the device 32
2.6 Connecting data cables 33
3 Making basic settings 34
4 First login (Password change) 35

4Installation BAT867-R
Release 10 09/2021
5 Obtaining compliance for operation in the
European Union and in the United Kingdom (UK) 36
6 Configuring the transmit power 39
7 Configuring WLAN transmission rates and
number of spatial streams 41
8 Maintenance and service 42
9Disassembly 43
9.1 Removing the device 43
10 Technical data 44
10.1 General technical data 44
10.2 Dimension drawings 45
10.3 Radio technology 46
10.4 Roaming 46
10.5 Receiving sensitivity, transmit power and data rate 47
10.5.1 IEEE 802.11b 47
10.5.2 IEEE 802.11g 47
10.5.3 IEEE 802.11a 48
10.5.4 IEEE 802.11n 48
10.5.5 IEEE 802.11ac 50
10.6 EMC and immunity 51
10.7 Network range 52
10.8 Power consumption/power output 52
11 Scope of delivery, order numbers and
accessories 53
12 Underlying technical standards 55
A Further support 56

Installation BAT867-R
Release 10 09/2021 5
Important information
Note: Read these instructions carefully, and familiarize yourself with the
device before trying to install, operate, or maintain it. The following notes may
appear throughout this documentation or on the device. These notes warn of
potential hazards or call attention to information that clarifies or simplifies a
procedure.
Symbol explanation
This is a general warning symbol. This symbol alerts you to
potential personal injury hazards. Observe all safety notes that
follow this symbol to avoid possible injury or death.
If this symbol is displayed in addition to a safety instruction of the
type “Danger” or “Warning”, it means that there is a danger of
electric shock and failure to observe the instructions will
inevitably result in injury.
This symbol indicates the danger of hot surfaces on the device.
In connection with safety instructions, non-observance of the
instructions will inevitably result in injuries.
DANGER
DANGER draws attention to an immediately dangerous situation, which will
inevitably result in a serious or fatal accident if not observed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a possible danger which, if not avoided, may result in
minor injuries.

6Installation BAT867-R
Release 10 09/2021
NOTICE
NOTE provides information about procedures that do not involve the risk of
injury.

Installation BAT867-R
Release 10 09/2021 7
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 44.
Connect to the product only components suitable for the requirements
of the specific application case.
Installation site requirements
Restricted access location:
The location is outside the operator access area.
The location is accessible to the service personnel even when the
device is switched on.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.

8Installation BAT867-R
Release 10 09/2021
Indoor operator access area:
The location is accessible without tools.
The person responsible for the area has provided access for the
operator intentionally.
The operator knows of the access possibilities, regardless of whether
they need a tool.
Mount the device at a maximum height of 2 m (78.74 in).
Relevant for Europe:
Supply only 24 V DC to the device and use a fuse.
Regarding the properties of this fuse: See “General technical data”
on page 44.
Strain relief
Note: If the strain relief is insufficient, there is a potential risk of torsion,
contact problems and creeping interruptions.
Relieve the connection points of cables and lines from mechanical
stress.
Design strain reliefs in such a way that they help prevent any
mechanical damage to cables, wires or conductors caused by external
influences or their own weight.
To help prevent damage to device connections, connectors and
cables, follow the instructions for proper installation in accordance with
DIN VDE 0100-520:2013-06, sections 522.6, 522.7 and 522.13.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
See “General technical data” on page 44.
Mount the device in the vertical position.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.

Installation BAT867-R
Release 10 09/2021 9
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
When installing antennas, observe the regulations of the country in
which you are operating the WLAN device with regard to the general
operating permission and the maximum emission levels.
Install and operate this equipment with a minimum distance of 50 cm
(19.7 in) between the antenna and your body.
Grounding the device
For the functional earth (FE), there is a separate functional earth screw on
top of the device. The functional earth is electrically connected to the
circuit ground and the metal housing of the device.
Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.

10 Installation BAT867-R
Release 10 09/2021
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
The voltage connected complies with the requirements for a safety extra-low voltage
(SELV) as per IEC 60950-1 or ES1 as per IEC/EN 62368-1.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
Table 1: Requirements for connecting electrical wires

Installation BAT867-R
Release 10 09/2021 11
Requirements for connecting the supply voltage
The supply voltage is connected to the device casing through protective
elements exclusively.
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the
device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (for example a
switch or a plug). This disconnecting device is clearly identified. So in the case of an
emergency, it is clear which disconnecting device belongs to which power supply
cable.
The power supply cable is suitable for the voltage, the current and the physical load.
Hirschmann recommends a conductor cross section of 0.5 mm² to 0.75 mm² (AWG20
up to AWG18).
The cross-section of the ground conductor is the same size as or bigger than the
cross-section of the power supply cables.
The following requirements apply alternatively:
Alternative 1 The power supply complies with the requirements for a limited power
source (LPS) according to IEC 60950-1 or PS2 according to IEC/
EN 62368-1.
Alternative 2 Relevant for North America:
The power supply complies with the requirements according to
NEC Class 2.
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-
low voltage (SELV) according to IEC 60950-1 or ES1 according to
IEC/EN 62368-1.
A back-up fuse suitable for DC voltage is located in the plus conductor
of the power supply.
The minus conductor is on ground potential. Otherwise, a back-up
fuse is also located in the minus conductor.
Regarding the properties of this back-up fuse:
See “Technical data” on page 44.
Table 2: Requirements for connecting the supply voltage

12 Installation BAT867-R
Release 10 09/2021
Lightning protection and surge protection
The lightning protection measures must be carried out by a lightning
protection professional in accordance with valid standards (such as
IEC 62305 / DIN EN 62305 (VDE 0185-305)), and in accordance with
the lightning protection procedures recognized and proven for the
application and the environment.
Refer to the information in the “WLAN Outdoor Guide” on “Lightning
protection and surge protection”.
The manual is available for download on the Internet: https://
www.doc.hirschmann.com
Ensure that the lightning protection professional installs lightning
protection devices (for example lightning conductors) to protect
antennas installed outdoors.
Ensure that the lightning protection professional takes appropriate
lightning protection measures that mitigate the effects of lightning
strikes.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU and 2015/863/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/53/EU (RED)
Directive of the European Parliament and of the council on the
harmonization of the laws of the Member States relating to the making
available on the market of radio equipment.
This product may be operated in all EU (European Union)
countries under the condition that it has been configured correctly.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be available to the relevant authorities at the following
address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
You find the EU conformity declaration as PDF file for downloading on the
Internet at: https://www.doc.hirschmann.com/certificates.html

Installation BAT867-R
Release 10 09/2021 13
The product can be used in residential areas (residential, commercial and
light-industrial environments) and in industrial areas.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
Safety: EN 62368-1
You find more information on technical standards here:
“Underlying technical standards” on page 55
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
Notes for countries with the following country codes:
The RED compliance requires compliant operation of the device in the
5 GHz band channels. Compliant operation of the device is achieved
by an unchangeable determination of the country setting. To obtain
RED compliance, perform the work steps described in chapter
“Obtaining compliance for operation in the European Union and in the
United Kingdom (UK)” on page 36.
AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IT LI
LT LU LV MT NL NO PL PT RO
RS SE SI SK TR

14 Installation BAT867-R
Release 10 09/2021
Notes for Germany (DE) and Ireland (IE):
Operation in the 5.8 GHz band at a radiated power (EIRP) >25 mW is
subject to meeting the following conditions:
Germany (DE)
Frequency range: 5725 MHz to 5875 MHz
Condition: The usage of this band is restricted to commercial public
telecommunication services. Registration at the Federal Network
Agency is required.
Name and website of the competent authority:
Bundesnetzagentur
www.bundesnetzagentur.de
Ireland (IE)
Frequency range: 5725 MHz to 5875 MHz
Condition: Registration of operational base stations
Name and website of the competent authority:
Commission for Communications Regulation
www.comreg.ie
DE IE

Installation BAT867-R
Release 10 09/2021 15
UKCA marking
The labeled devices comply with the following UK regulations:
S.I. 2012 No. 3032 Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronical Equipment Regulations
S.I. 2017 No. 1206 Radio Equipment Regulations
The UKCA conformity declaration will be available to the relevant
authorities at the following address:
Belden UK Ltd.
1 The Technology Centre, Station Road
Framlingham, IP13 9EZ, United Kingdom
You find the UKCA conformity declaration as PDF file for downloading on
the Internet at: https://www.doc.hirschmann.com/certificates.html

16 Installation BAT867-R
Release 10 09/2021
Notes for the United Kingdom (UK):
The Radio Equipment Regulations compliance requires compliant
operation of the device in the 5 GHz band channels. Compliant
operation of the device is achieved by an unchangeable determination
of the country setting. To obtain the Radio Equipment Regulations
compliance, perform the work steps described in chapter “Obtaining
compliance for operation in the European Union and in the United
Kingdom (UK)” on page 36.
Operation in the 5.8 GHz band at a radiated power (EIRP) >25 mW is
subject to meeting the following conditions:
Frequency range: 5725 MHz to 5850 MHz
Condition: Light-licensing regime
Name and website of the competent authority:
Ofcom
www.ofcom.org.uk
UK

Installation BAT867-R
Release 10 09/2021 17
FCC note
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
BAT867-R
U.S. Contact Information
Belden – St. Louis
1 N. Brentwood Blvd. 15th Floor
St. Louis, Missouri 63105, United States
Phone: [phone]
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reposition the receiver antenna or change the angle of the receiver
antenna.
Increase the separation between the device and the receiver.
Connect the device to a different power supply from that to which the
receiver is connected.
Consult a specialist retailer or an electronic systems engineer for help.
Changes or modifications not expressly approved by the holder of the
certificate could void the user’s authority to operate this equipment.

18 Installation BAT867-R
Release
10
09/2021
Note for the use in the USA and in Canada
The following section applies to BAT867-R variants with the characteristic value US (USA/Canada) for country
approvals which are labeled as follows:
Contains Transmitter Module
FCC ID: TK4WLE600VX
IC: 7849A-WLE600VX
This equipment complies with FCC and IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. Install and operate this equipment with a minimum distance of 50 cm (19.7 in) (related to a 9 dBi
antenna) between the radiation source and your body.
The antenna used for this transmitter must not be co-located with any other transmitters within a host device, except
in accordance with FCC multi-transmitter product procedures.
This transmitter is restricted to indoor use only within the 5.15 to 5.25 GHz band to reduce potential for harmful
interference to co-channel mobile satellite systems.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.
Antenna(s) for operation with this
device:
Permitted band of operation
2.4 GHz band 5 GHz band
5180 ... 5240 MHz 5260 ... 5320 MHz 5500 ... 5720 MHz 5745 ... 5825 MHz
BAT-ANT-RSMA-2AGN-Ra
a. Note: When using 2 antennas type BAT-ANT-RSMA-2AGN-R, you must align each antenna in another spatial direction (x-y) so that both antennas
are arranged at right angles to each other.
Yes Yes Yes Yes Yes
BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes Yes Yes

Installation BAT867-R
Release 10 09/2021 19
The FCC approval is valid only in conjunction with the listed antennas. If
other antennas are used, the approval expires. The responsibility lies with
the operator of the system. The required antenna impedance is 50 .
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

20 Installation BAT867-R
Release 10 09/2021
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
Documentation mentioned in the “User Manual Installation” that is not
supplied with your device as a printout can be found as PDF files for
downloading on the Internet at: https://www.doc.hirschmann.com