Belkin SOUNDFORM AUC001 Setup guide

How to set your Belkin SOUNDFORM™ True Wireless Earbuds, AUC001 into
pairing mode
Before you can pair your Belkin SOUNDFORM™ True Wireless Earbuds, AUC001
with your device, they need to be in pairing mode. This article will walk you
through setting your earbuds into pairing mode.
Before you begin
From the factory, your earbuds come in pairing mode. If you just purchased the
earbuds, simply open the charging case and remove the earbuds from it. The
indicator lights on the earbuds will alternate between blue and white.
NOTE: If the indicator lights on your earbuds do not alternate between blue and
white when removed from the case, proceed to the steps below.

Step 1:
Ensure your earbuds are turned OFF. To do this, press on both earbuds and hold
for 6 seconds and then release.
Step 2:
Verify that your earbuds are turned OFF, then press and hold on both earbuds for
10 seconds. This will turn your earbuds back ON and place them into pairing
mode.
You can now proceed with pairing your earbuds. Click here for instructions.
How to pair the Belkin SOUNDFORM™ True Wireless Earbuds, AUC001
Pairing the Belkin SOUNDFORM™ True Wireless Earbuds, AUC001 with your
Bluetooth®-enabled mobile device allows you to listen to audio without the use of
wires. This article will walk you through the steps on pairing your earbuds to your

phone or tablet.
Before you begin
Ensure that your earbuds are removed from the charging case and are in pairing
mode. For instructions on how to set your earbuds to pairing mode, click here.
NOTE: Your earbuds' lights will alternately flash between blue and white to
indicate that both are on pairing mode.
Step 1:
On your mobile device, turn ON Bluetooth to begin searching for nearby devices.
NOTE: Steps in enabling your Bluetooth may vary depending on your device's
operating system.

Step 2:
When your earbuds are detected, it will show as SOUNDFORM True Wireless
Earbuds. Tap on the name to complete pairing.
Your earbuds will make a confirmation sound once paired. It will also show on
your phone or tablet as a paired device.
How to charge the Belkin SOUNDFORM™ True Wireless Earbuds, AUC001
The case of the Belkin SOUNDFORM™ True Wireless Earbuds, AUC001 contains a
battery which allows you to charge, no matter where you are, without worrying
about finding a power outlet for your earbuds.
This article will show you how to charge the Belkin AUC001. Click the links below
for specific instructions.

Charging your earbuds
Charging the case
Charging your earbuds
To charge your earbuds, simply open the case and place each earbud in its
designated slot and close the lid. If the case has battery power remaining, you do
not need to plug it in while charging your earbuds.
NOTE: Connecting your case to a power outlet while charging the earbuds will
not increase the charging speed of the earbuds.

Charging the case
Step 1:
Connect the micro-USB end of the connector to the back of the charging case,
below the lid hinge.
Step 2:
Connect the USB end of the connector to a power adapter or into the USB port of
your computer.

Step 3:
Wait for all four lights to turn ON indicating that it has been fully charged. The
indicator lights at the front will provide an approximation of how much charge is
on the Belkin AUC001.
The number of lights lit correspond to the following:
•Four lights –100% charged
•Three lights –75% charged
•Two lights –50% charged
•One light –less than 25% charged

The case will change from charge mode to a trickle charge maintenance mode
once it reaches 100%. This means it is safe to keep your case plugged in even if it
is fully charged.
You can remove the case from power at any time or any charge level. A lower
charge level, however, will reduce the number of times you can recharge your
earbuds before the case is out of power.