Belkin SOUNDFORM User manual

True Wireless Earbuds
Initial pairing
From the factory, your earbuds come in pairing mode. If you just
purchased the earbuds, simply open the charging case and remove
the earbuds from it. The indicator lights on the earbuds will alternate
between blue and white..
Step 1: On your mobile device, turn ON Bluetooth to begin
searching for nearby devices.
Step 2: When your earbuds are detected, it will show as
SOUNDFORM True Wireless Earbuds. Tap on the name to complete
pairing. Your earbuds will make a confirmation sound once paired.
It will also show on your phone or tablet as a paired device.
Audio Playback
Control Left Earbud Right Earbud
Volume up ( + ) Tap one time
Volume down ( - ) Tap one time
Pause / Resume playback Tap two times Tap two times
Next track Tap three times
Previous track Tap three times
Call Handling
Control Left Earbud Right Earbud
Accept / End call Tap two times Tap two times
Reject call Hold for 2 seconds Hold for 2 seconds
Virtual Assistants
Control Left Earbud Right Earbud
Activate virtual assistant Hold for 2 seconds Hold for 2 seconds
How to use the touch controls on the Belkin AUC002
6sec
10sec
1 2 Set your earbuds to pairing mode
Step 1: Ensure your earbuds are turned OFF. To do this, press on both
earbuds and hold for 6 seconds and then release.
Step 2: Verify that your earbuds are turned OFF, then press and hold
on both earbuds for 10 seconds. This will turn your earbuds back ON
and place them into pairing mode. You can now proceed with pairing
your earbuds.
10 sec6 sec
6sec
10sec
How to unpair your earbuds
Your earbuds should be turned OFF. To do
this, you can do either of the two options:
a. Press on both earbuds for 6 seconds.
b. Return the earbuds to the charging case
and close the lid.
To unpair them, follow the instructions below:
For Android™
Step 1: Go to Settings.
Step 2: Tap on Connections > Bluetooth.
Step 3: Under Paired devices, select the
paired earbuds then tap Unpair.
For iOS
Step 1: Go to Settings.
Step 2: Tap on Bluetooth.
Step 3: Under MY DEVICES, tap the info
icon on the paired earbuds and then tap
on Forget This Device.

Resetting your earbuds to factory settings
If, for instance, you are only able to pair one earbud to your phone or tablet, the best solution to this issue would be to reset your earbuds
to factory settings and pair the earbuds again. Follow the step-by-step instructions below to learn how:
Step 1: On your phone or tablet, go to Settings and unpair the earbuds (see page 1 for instructions).
Step 2: Press on both earbuds simultaneously for 6 seconds to turn OFF your earbuds.
Step 3: Press and hold on both earbuds for 10 seconds. This will reset the device. Release when the indicator lights turn OFF.
Step 4: Return the earbuds to the charging case and close the lid.
Step 5: Open the case and take out the earbuds.
NOTE: It takes around 4 to 5 seconds for the left and right earbuds to connect to each other.
Step 6: On your mobile device, turn ON Bluetooth® to search for nearby devices, and begin pairing. Steps in enabling Bluetooth may vary
depending on your device’s operating system. When detected, select your earbuds from the list of Bluetooth devices.
Wait for about 2 to 3 seconds for both of the earbuds’ indicator lights to flash blue and turn OFF.
How to charge the case
and the earbuds
Case: Connect the micro-USB end of the
connector to the back of the charging case,
below the lid hinge. Connect the USB end
of the connector to a power adapter or into
the USB port of your computer.
Earbuds: To charge your earbuds, simply
open the case and place each earbud in
its designated slot and close the lid. If the
case has battery power remaining, you do
not need to plug it in while charging your
earbuds.
NOTE: Connecting your case to
a power outlet while charging the earbuds
will not increase the charging speed of
the earbuds.
True Wireless Earbuds
6sec
10sec
SOUNDFORM Buds
SOUNDFORM Buds
1
4
2
5
3
6
6 sec
6sec
10sec
10 sec
6sec
10sec