Belkin F9J1005 User manual

Wireless ModeM router
N300
N300 WIRELESS MODEM ROUTER
User Manual
F9J1005v1 8820ed01125uk Rev.A00
ENGLISH
OR

TABLE OF CONTENTS
GETTING STARTED ........................................3
What’s in the Box ............................................. 3
Initial Setup.................................................. 3
How to Set It UP .............................................. 3
Advanced Tools & Settings..................................... 6
Adding Computers to Your Network ............................. 7
GETTING TO KNOW YOUR ROUTER ..........................8
Front Panel .................................................. 8
Back Panel .................................................. 9
TECHNICAL DETAILS......................................10
Technical Features .......................................... 10
System Requirements........................................ 11
TROUBLESHOOTING, SUPPORT, AND WARRANTY ...........12
Troubleshooting ............................................. 12
Technical Support ........................................... 15
Warranty ................................................... 16
How to get service? .......................................... 17
REGULATORY INFORMATION ..............................18
Declaration of Conformity with electromagnetic compatibility and
electromagnetic interference .................................. 18
Europe – EU Declaration of Conformity ......................... 19
General Safety Information: ................................... 19

3
GETTING STARTED
What’s in the Box
N300 Wireless Modem-Router
ADSL cable
Power supply
Ethernet cable
Network information card
Belkin Setup CD with User Manual
Initial Setup
Where to Place Your Router
For the best results, place the Router in an open location away from large
metal objects and magnets such as those found in speakers. Raising the
Router above floor level can improve the strength of your wireless signal.
How to Set It UP
Connect Your N300 Router
1. Connect your Router’s ADSL cable to your phone jack or phone-
jack adapter (microfilter). If you are replacing an existing Router
or gateway, this may require unplugging the existing gateway.
Note: If required by your Internet Service Provider (ISP), plug the included
phone-jack adapter (microfilter) into your wall-mounted phone jack. Please
check with your provider before connecting your Router if you are unsure
whether or not you need to use the included phone-jack adapter.
2. Plug the Router’s power supply into a wall outlet.
3. If your PC has been installed with a wireless adapter,
search for wireless networks on your computer, connect to
the wireless network which matches the ‘’Network Name
(SSID)” on the label on the underside of your router.

4
GETTING STARTED
4. When prompted, enter the password shown on
the label on the underside of the router.
5. Open the Internet Explorer (IE) browser and enter
http://192.168.2.1. In the Login page displayed, enter
the username admin and password admin.
6. After logining in, you will see the main interface below. Click Wizard
from the main menu on the left. It will guide you through fast and
accurate Internet connection. Click finish to finish, and now you
are connected to the Internet via your new Belkin Router.

5
GETTING STARTED
During setup you may be asked for additional information.
You may need to enter a username and password provided by your ISP.
This username and password is likely to be found on materials that came
from your ISP when you signed up for service. If necessary, you may
need to contact your ISP to retrieve your username and password.
If you have a static IP address, you may need to enter
additional information also provided by your ISP.
If your PC has been installed with a wired network card, connect
your PC to a LAN interface of the Router using the Ethernet cable.
Configure the TCP/IP properties of your network card to Obtain an
IP address automatically from modem, or set the IP address of the
computer as 192.168.2.X/255.255.255.0. The X is from 2 to 254.
Enter your VCI and VPI information provided by your ISP.

6
GETTING STARTED
Advanced Tools & Settings
After the initial setup is complete, you have the option to change
settings like your network name, security type, and password.
Network Name & Security
In the main menu, click Wireless > Basic Settings. You
can personalize your Network Name (SSID).
In the main menu, click Wireless > Security. You can change password and
the strength of wireless security.

7
GETTING STARTED
Adding Computers to Your Network
Wireless devices such as computers, network printers, and gaming
systems can connect to your Router with a few simple steps.
Manual Setup
You can manually add additional computers or
wireless devices to your network.
1. Locate the wireless > network > connections option
on your computer or wireless device.
2. Select your Belkin Router from the list of available networks. You
can identify your Belkin Router by locating the network name
(SSID) from the card located underneath the foot of your Router.
3. Enter your network password (located on your network information card).
Your wireless device will take a few moments to connect to your
network. If the connection is not made the first time, try this process
again. If you still have difficulty connecting to your network after
trying this process a few times, see the “Troubleshooting” section
in this manual for help with connecting to your network.
Note: In some cases you may be prompted to select the security
type. It is printed on the card for your convenience.
Using the WPS Button
1. Start WPS Push Button Connection (WPS PBC) on your computer
or other Wi-Fi device that you would like to connect wirelessly to your
Router. Often there will be a button for this purpose in software that
came with the device, or a physical “WPS” button on the device itself.
2. Within two minutes, press the WPS button on your Router.
The WPS indicator will blink green while it listens for your Wi-Fi device. Once
a connection is established, the light will turn green for about 5 minutes
and then go out. If a connection is not established, the light will blink green
for 2 minutes and 30 seconds. You may repeat the process to try again.
You can repeat this process for each WPS-enabled
device you’d like to add to your network.

8
GETTING TO KNOW YOUR ROUTER
Front Panel
Your Router’s status is shown by the lights on the front panel.
Power Light
Off: The Router is powered off.
Solid Green: Intialization of the Router is successful.
Solid Red: The Router is self-testing, or self-testing is
failed, or software upgrade is under progress.
Modem Light
Solid Green: Connection between the Router and the
physical layer of the modem is established.
Slow Blinking Green:No signal is being detected.
Fast Blinking Green: The Router is handshaking
with the physical layer of the modem.
Internet Light
Off: The Router is in bridged mode, or no data is transmitted via a WAN port.
Blinking Green: Data is being transmitted in routing mode or bridged mode.
Solid Red: The Internet connection fails after successful
synchronization in routing mode (for example: PPP dial-up is failed).
LAN Light
Off: LAN connection is not created.
Blinking Green: LAN data is being transmitted, or Internet
data is being transmitted in bridged mode.
Solid Green: LAN connection is established and activated.
WLAN Light
Off: WLAN is disabled.
Blinking Green: Wireless data is being transmitted in the WLAN.
Solid Green: WLAN is enabled but no data is transmitted.
Wi-Fi Protected Setup (WPS) Light
Off: Idle
Blinking Green: The Router is listening for a WPS-
enabled computer or other device.
Successful Connection:The WPS light is SOLID GREEN
for 5 minutes and then goes out when the Router has made a
secure connection with the computer or other device.
Failed Connection: The WPS light is BLINKING GREEN for 2
minutes and 30 seconds after the WPS connection fails.

GETTING TO KNOW YOUR ROUTER
9
Back Panel
WPS Button
This button is used to help establish secure connection between your
Router and other WPS-enabled Wi-Fi devices such as computers.
To use the WPS feature on your Router, see “Getting Started >
Adding Computers to Your Network > Using the WPS Button”.
Modem (WAN) Connector
Connect your Router to a phone jack using a telephone
cord. In some areas, a microfilter might be required.
Wired (LAN) Connectors
Connect computers and other wired network devices
to these ports using Ethernet cables.
Power Connector
Connect the included power supply to this jack.
Reset Button
This button is used to restart your Router in rare cases when it
functions incorrectly. Resetting the Router will preserve your settings.
This button may also be used to restore the factory default settings.
Please see the Troubleshooting section for more information. To reset
the Router, press and hold this button for at least 10 seconds.

10
TECHNICAL DETAILS
Technical Features
Integrated ADSL2+ Modem
The integrated ADSL2+ modem allows you to connect to the
Internetyou’re your local Internet Service Provider (ISP) without
installing and maintaining a separate DSL modem.
Integrated 802.11n Wireless Access point
The N300 technology enhances your Router’s wireless capabilities,
allowing for data transfer speeds of up to 300Mbps across your network.
NAT IP Address Sharing
To save you the cost of adding IP address per computer in your house,
our Belkin Router uses Network Address Translation (NAT) technology,
allowing you to share a single IP address across your network.
SPI Firewall
Your Router is equipped with a firewall that will protect your
network from a wide array of common attacks and viruses.
Universal Plug-and-Play (UPnP) Compatibility
The UPnP (Universal Plug-and-Play) feature in your Router
offers seamless operation of voice and video messaging,
games, and other applications that are UPnP-compliant.
Web-Based Advanced User Interface
You can easily make changes to your Route’s advanced
settings through your web browser. These changes can
be made from any computer on your network.
Integrated 4-Port 10/100 Switch
Your Router has a built-in, 4-port network switch to allow your wired
computers to share: printers, data, MP3 files, digital photos, and much more.

TECHNICAL DETAILS
11
System Requirements
Modem Router
Broadband ADSL Internet connection with RJ11 (telephone) connection
At least one computer with an installed network interface adapter
TCP/IP networking protocol installed on each computer
RJ11 ADSL telephone cable
Internet browser
Setup Software
A computer running Windows®XP SP3 and higher,
Windows Vista® 32 and 64 bit, or
Windows 7 32 and 64 bit, or
Mac OS® X, 10.5 and 10.6
Minimum 1GHz processor and 256MB RAM
600MB of free hard-drive space for installation

12
TROUBLESHOOTING, SUPPORT, AND WARRANTY
Troubleshooting
I can’t connect to the Internet wirelessly.
The Power and WLAN lights are solid green and your Router is
connected to the Internet. However, you cannot connect to the
Router’s wireless network. Please refer to “Adding Computers
to Your Network” in this manual for instructions.
I can’t connect to the Internet wirelessly and my
network name is not listed in Available Networks.
1. Verify that your Router is on and the Power, WLAN and
Modem lights on the front panel show solid green.
2. If you are far from the Router, you might try moving
closer to see if you might have been out of range.
3. Using a computer attached to the Router via a network cable, visit
http://192.168.2.1 and ensure that “Broadcast SSID” is ON. This
setting is found on the “Wireless Advanced Settings” page.
My wireless network performance is slow, inconsistent, suffers from
weak signal, or I’m having difficulty maintaining a VPN connection.
Wireless technology is radio-based, which means connectivity and
the throughput performance between devices decreases when the
distance between devices increases. Other factors that will cause
signal degradation (metal is generally the worst culprit) are obstructions
such as walls and metal appliances. Note also that connection
speed may decrease as you move farther away from the Router.
In order to determine if wireless issues are related to range, we suggest
temporarily moving the computer within 10 feet from the Router if possible.
Changing the wireless channel—Depending on local wireless traffic and
interference, switching the wireless channel of your network can improve
performance and reliability. Visit http://192.168.2.1 and choose other channels
on the “Wireless Basic Settings” page under the “Wireless” heading.
Limiting the wireless transmit rate—Limiting the wireless transmit
rate can help improve range and connection stability. Most wireless
cards have the ability to limit the transmission rate. To change this
property in Windows, go to the Windows Control Panel, open “Network
Connections”, and double-click on your wireless card’s connection. In
the properties dialog, select the “Configure” button on the “General”
tab, then choose the “Advanced” tab and select the rate property.
Wireless client cards are usually set to automatically adjust the wireless
transmit rate for you, but doing so can cause periodic disconnections
when the wireless signal is too weak; as a rule, slower transmission
rates are more stable. Experiment with different connection rates
until you find the best one for your environment. Note that all available
transmission rates should be acceptable for browsing the Internet.
For more assistance, see your wireless card’s user manual.

TROUBLESHOOTING, SUPPORT, AND WARRANTY
13
I’ve installed this new Router and some of my network clients
(computers, game consoles, ect.) are now unable to connect.
Your new Router came pre-configured with a network name and
password, found printed on an attached card. All clients must use this
network name and password to connect wirelessly to your Router.
You will need to find the network settings on your client, select the
network name printed on the card from the list of available networks,
and enter the password when prompted to join the wireless network.
Does the Router support Wireless Protected Access (WPA) security?
The Router ships with WPA/WPA2 security turned on.
Windows XP and some older network hardware may
require a software update to support WPA/WPA2.
I am having difficulty setting up WPA security on my Router.
1. Log in to your Router by visiting http://192.168.2.1 with your Web browser.
Click on the “Login” button in the top right-hand corner of the screen.
You will be asked to enter your password. If you have never set a
password, leave the “Password” field blank and click “Submit”.
2. Click “Security” under the “Wireless” heading in the left-hand menu.
3. Select the “WPA/WPA2” option.
4. Enter a password. This can be from 8-63 characters of your choice,
including spaces and punctuation, OR a 64-digit hexadecimal
number (using only the numbers 0-9 and letters A-F).
5. Click “Apply Changes” to finish. Your wireless connection
is now encrypted. Each computer using your wireless
network will need to use the new key.
Note: If you are configuring the Router over a wireless connection, you will
have to re-connect to the Router after changing any security settings.
Note: Some older networking hardware supports only WEP encryption.
If your older computers cannot connect to your network, try 128-bit or
64-bit WEP, or seek software updates from their manufacturers.

TROUBLESHOOTING, SUPPORT, AND WARRANTY
14
I am having difficulty setting up WEP security on my Router.
1. Log in to your Router by visiting http://192.168.2.1 with your Web
browser.Click on the “Login” button in the top right-hand corner of the
screen. You will be asked to enter your password. If you have never
set a password, leave the “Password” field blank and click “Submit”.
2. Click “Security” under the “Wireless” heading in the left-hand menu.
3. Select the “WEP” option.
4. You may choose 128-bit key length, and then type in a WEP key
composed of 26 hexadecimal digits (0-9, A-F). For example, C3 03
0F AF 4B B2 C3 D4 4B C3 D4 EE 74 is a valid 128-bit WEP key.
5. Click “Apply Changes” to finish. Your wireless connection
is now encrypted. Each computer using your wireless
network will need to use the new key.
Note: If you are configuring the Router over a wireless connection, you will
have to re-connect to the Router after changing any security settings.
Note: Some older networking hardware supports only 64-bit WEP encryption.
If your older computers cannot connect to your network, try 64-bit WEP.

TROUBLESHOOTING, SUPPORT, AND WARRANTY
15
Technical Support
AUSTRIA 0820 200 766 www.belkin.com/de/networking/
BELGIUM 07 07 00 073 www.belkin.com/nl/networking/
www.belkin.com/fr/networking/
CZECH REPUBLIC 239 000 406 www.belkin.com/uk/networking/
DENMARK 701 22 403 www.belkin.com/uk/networking/
FINLAND 0972519123 www.belkin.com/uk/networking/
FRANCE 08 - 25 54 00 26 www.belkin.com/fr/networking/
GERMANY 0180 - 500 57 09 www.belkin.com/de/networking/
GREECE 00800 - 44 14 23 90 www.belkin.com/uk/networking/
HUNGARY 06 - 17 77 49 06 www.belkin.com/uk/networking/
ICELAND 800 8534 www.belkin.com/uk/networking/
IRELAND 0818 55 50 06 www.belkin.com/uk/networking/
ITALY 02 - 69 43 02 51 www.belkin.com/it/networking/
LUXEMBOURG 34 20 80 85 60 www.belkin.com/uk/networking/
NETHERLANDS 0900-040 07 90 €0.10min www.belkin.com/nl/networking/
NORWAY 81 50 0287 www.belkin.com/uk/networking/
POLAND 00800 - 441 17 37 www.belkin.com/uk/networking/
PORTUGAL 707 200 676 www.belkin.com/uk/networking/
RUSSIA 495 580 9541 www.belkin.com/networking/
SLOVAKIA 08000 04614 www.belkin.com/networking/
SLOVENIA 0800 80510 www.belkin.com/networking/
SOUTH AFRICA 0800 - 99 15 21 www.belkin.com/uk/networking/
SPAIN 902 - 02 43 66 www.belkin.com/es/networking/
SWEDEN 07 - 71 40 04 53 www.belkin.com/uk/networking/
SWITZERLAND 08 - 48 00 02 19 www.belkin.com/de/networking/
UNITED KINGDOM 0845 - 607 77 87
www.belkin.com/fr/networking/
www.belkin.com/uk/networking/
OTHER COUNTRIES +44 - 1933 35 20 00 www.belkin.com/it/networking/

TROUBLESHOOTING, SUPPORT, AND WARRANTY
16
Warranty
What this warranty covers
Belkin International, Inc. (“Belkin”) warrants to the original
purchaser of this Belkin product that the product shall be free
of defects in design, assembly, material, or workmanship.
What the period of coverage is
Belkin warrants the Belkin product for two years.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of
charge (except for shipping charges for the product). Belkin reserves the
right to discontinue any of its products without notice, and disclaims any
limited warranty to repair or replace any such discontinued products.
In the event that Belkin is unable to repair or replace the product (for
example, because it has been discontinued), Belkin will offer either a
refund or a credit toward the purchase of another product from Belkin.
com in an amount equal to the purchase price of the product as evidenced
on the original purchase receipt as discounted by its natural use.
What is not covered by this warranty?
All above warranties are null and void if the Belkin product is not
provided to Belkin for inspection upon Belkin’s request at the sole
expense of the purchaser, or if Belkin determines that the Belkin
product has been improperly installed, altered in any way, or tampered
with. The Belkin Product Warranty does not protect against acts
of God such as flood, lightning, earthquake, war, vandalism, theft,
normal-use wear and tear, erosion, depletion, obsolescence, abuse,
damage due to low voltage disturbances (i.e. brownouts or sags), non-
authorized program, or system equipment modification or alteration.

TROUBLESHOOTING, SUPPORT, AND WARRANTY
17
How to get service?
To get service for your Belkin product you must take the following steps:
1. Contact Belkin Tech Support (p 14) within 15 days of the
Occurrence. Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then
instruct you on how to forward your receipt and Belkin
product and how to proceed with your claim.
Belkin reserves the right to review the damaged Belkin product. All costs of
shipping the Belkin product to Belkin for inspection shall be borne solely by
the purchaser. If Belkin determines, in its sole discretion, that it is impractical
to ship the damaged equipment to Belkin, Belkin may designate, in its sole
discretion, an equipment repair facility to inspect and estimate the cost to
repair such equipment. The cost, if any, of shipping the equipment to and
from such repair facility and of such estimate shall be borne solely by the
purchaser. Damaged equipment must remain available for inspection until the
claim is finalized. Whenever claims are settled, Belkin reserves the right to be
subrogated under any existing insurance policies the purchaser may have.
How state law relates to the warranty?
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN.
THERE ARE NO OTH ER WARRANTIES, EXPRESSED OR, EXCEPT AS
REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY
OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY,
ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL,
DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES
SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS
ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have
other rights, which may vary from state to state. Some states do
not allow the exclusion or limitation of incidental, consequential, or
other damages, so the above limitations may not apply to you.

18
REGULATORY INFORMATION
Declaration of Conformity with electromagnetic com-
patibility and electromagnetic interference
We, Belkin International, Inc., of Schiphol-Rijk, Netherlands, declare under our
sole responsibility that the device, F9J1005, complies with Directives stated in
our EU declaration which can be obtained from our website given below.
Caution: Exposure to Radio Frequency Radiation.
This equipment complies with radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and your body
CISPR 22 Interference Notice
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to the requirements of EN 55022 and
EN 55024. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.

REGULATORY INFORMATION
19
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC, the EMC Directive 2004/108/EC, and the low-voltage
Directive 2006/95/EC. A copy of the European Union CE marking “Declaration of Conformity” may be obtained at the website: www.belkin.com/doc
For information on product disposal please refer to
http://environmental.belkin.com
General Safety Information:
• For indoor installation only
• For installation with supplied power adapter only
• The supplied power adapter is the product’s switch-off device. The base socket must be near the product and easily accessible.

© 2012 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective
manufacturers listed. iPad, iPhone, iPod touch, Mac, Mac OS, and Safari are trademarks of Apple Inc.,
registered in the U.S. and other countries. Windows, Windows Vista, Internet Explorer, and DirectX are either
registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
Belkin Iberia
Avda de Barajas, 24, Edificio Gamma,
4ªpta, 28108 Alcobendas
Madrid - Spain
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
Belkin Italy & Greece
Via Nino Bonnet, 4/6
Milan 20154
Italy
Belkin GmbH
Otto-Hahn-Straße 20
85609 Aschheim
Germany
Belkin B.V.
Tupolevlaan 1
1119 NW Schiphol-Rijk,
Netherlands