Belkin F1DU120 - Pulse Network Monitor User manual

F1DUXXXea
Quick Installation Guide
NL
ES
IT
EN
FR
DE

P75340ea_F1DUXXXea_QIG.indb 1 29/11/06 1:57:46 pm

P75340ea_F1DUXXXea_QIG.indb 2 29/11/06 1:57:46 pm

P75340ea_F1DUXXXea_QIG.indb 3 29/11/06 1:57:47 pm

© 2006 Belkin Corporation. All rights reserved. All trade names are registered
trademarks of respective manufacturers listed. Mac and Mac OS are trademarks
of Apple Computer, Inc., registered in the U.S. and other countries.
Belkin Corporation
501 West Walnut Street
Compton, CA, 90220-5221
USA
[phone]
[phone] fax
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
[phone]
[phone] fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, Netherlands
[phone]
[phone] fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich, Germany
[phone]
[phone] fax
Belkin SAS
130 rue de Silly
92100 Boulogne-Billancourt, France
[phone]
[phone] fax
Belkin Iberia
Avda. Cerro del Aguila 3
28700 San Sebastián de los Reyes, Spain
[phone]
[phone] fax
Belkin Nordic
Knarrarnäsgatan 7
164 40 Kista, Sweden
[phone]
[phone] fax
Belkin Tech Support
00 800 223 55 460
P75340ea
P75340ea_F1DUXXXea_QIG.indb 4 29/11/06 1:57:47 pm

F1DUXXXea
Quick Installation Guide
NL
ES
IT
EN
FR
DE

P75340ea_F1DUXXXea_QIG.indb 5 29/11/06 1:57:48 pm

Introduction | 1
To install Pulse, you will need the following:
Introduction
This Quick Installation Guide provides the steps you will need to
install your Belkin Pulse. Should you encounter a problem during this
installation, please visit www.belkin.com/pulse for more information.
Ethernet Cable
Pulse 5V DC, 2.5A
Power Supply
Modem Cable
(optional) Crossover Cable
(optional)
USB-to-Ethernet
Adapter (optional)
P75340ea_F1DUXXXea_QIG.indb 6 29/11/06 1:57:49 pm

Plug In Network | 2
To install Pulse, you will need the following:
Plug the orange Ethernet cable into the Ethernet port on the back of Pulse.
Plug the other end into your network hub or switch.
PULSE
LINE PHONE
RST
Step 1 Plug in network
Installation Instructions
P75340ea_F1DUXXXea_QIG.indb 7 29/11/06 1:57:50 pm

Plug In Modem | 3
Step 2 Plug in modem
(optional)
Plug the black modem cable into the modem port labeled “PHONE” on Pulse.
Plug the other end into your telephone-line jack.
PULSE
LINE PHONE
RST
P75340ea_F1DUXXXea_QIG.indb 8 29/11/06 1:57:52 pm

Note:
The unit will try to acquire a DHCP address
during power up. A static IP address can be
assigned through the Web Console or the
Pulse Dashboard.
Plug In Modem | 4
Step 3 Plug in power
Plug the power cord into Pulse and connect to a power source.
PULSE
LINE PHONE
RST
P75340ea_F1DUXXXea_QIG.indb 9 29/11/06 1:57:52 pm

Detect Connectivity | 5
Step 4 Detect connectivity
The blue light blinks while the unit is powering up and after a few minutes,
both the amber and blue lights should be solid. The amber light will flicker
occasionally to indicate data transmission.
Note:
If Pulse loses Internet connectivity, the blue light will blink rapidly until the connection
is restored. If the modem cable is plugged in, Pulse will try to switch over to an analog
modem connection. The blue light blinks slowly when Pulse is connected via the modem.
ACT
P75340ea_F1DUXXXea_QIG.indb 10 29/11/06 1:57:54 pm