Belkin F5D7000CE2 Service manual

Report No.: RM920221R04A 1Issued: Mar. 14, 2003
Reference No.: RM920221R04
IMMUNITY TEST REPORT
REPORT NO.: RM920221R04A
MODEL NO.: F5D7000
RECEIVED: Feb. 21, 2003
TESTED: Feb. 27 ~ Mar. 7, 2003
APPLICANT: Belkin Corporation
ADDRESS:501 WEST WALNUT STREET COMPTON,
CA 90220
ISSUED BY: Advance Data Technology Corporation
LAB LOCATION: No.47 14th Ling, Chia Pau Tsuen, Linkou
Hsiang, Taipei, Taiwan, R.O.C.
This test report consists of 29 pages in total. It may be duplicated completely for legal use with the
approval of the applicant. It should not be reproduced except in full, without the written approval of
our laboratory. The client should not use it to claim product endorsement by NVLAP or any U.S.
government agencies. The test results in the report only apply to the tested sample.
0528
ILACMRA

Report No.: RM920221R04A 2Issued: Mar. 14, 2003
Reference No.: RM920221R04
Table of Contents
1 CERTIFICATION ..................................................................................................................... 3
2 SUMMARY OF TEST RESULTS ............................................................................................ 4
3 GENERAL INFORMATION ..................................................................................................... 5
3.1 GENERAL DESCRIPTION OF EUT ........................................................................................5
3.2 DESCRIPTION OF TEST MODE.............................................................................................6
3.3 GENERAL DESCRIPTION OF APPLIED STANDARD ...........................................................6
3.4 DESCRIPTION OF SUPPORT UNIT.......................................................................................7
4 EMISSION TEST..................................................................................................................... 8
4.1 CONDUCTED EMISSION MEASUREMENT ..........................................................................8
4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................................8
4.1.2 TEST INSTRUMENTS .............................................................................................................8
4.1.3 TEST PROCEDURES..............................................................................................................9
4.1.4 DEVIATION FROM TEST STANDARD....................................................................................9
4.1.5 TEST SETUP .........................................................................................................................10
4.1.6 EUT OPERATING CONDITIONS ..........................................................................................10
4.1.7 TEST RESULTS.....................................................................................................................11
5 IMMUNITY TEST ..................................................................................................................13
5.1 GENERAL DESCRIPTION ....................................................................................................13
5.2 GENERAL PERFORMANCE CRITERIA DESCRIPTION .....................................................13
5.3 EUT OPERATING CONDITION.............................................................................................15
5.4 ELECTROSTATIC DISCHARGE IMMUNITY TEST (ESD) ...................................................16
5.4.1 TEST SPECIFICATION..........................................................................................................16
5.4.2 TEST INSTRUMENT .............................................................................................................16
5.4.3 TEST PROCEDURE ..............................................................................................................17
5.4.4 DEVIATION FROM TEST STANDARD..................................................................................17
5.4.5 TEST SETUP .........................................................................................................................18
5.4.6 TEST RESULT .......................................................................................................................19
5.5 RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST (RS) .21
5.5.1 TEST SPECIFICATION .........................................................................................................21
5.5.2 TEST INSTRUMENT .............................................................................................................21
5.5.3 TEST PROCEDURE ..............................................................................................................22
5.5.4 DEVIATION FROM TEST STANDARD..................................................................................22
5.5.5 TEST SETUP .........................................................................................................................23
5.5.6 TEST RESULT .......................................................................................................................24
6 PHOTOGRAPHS OF THE TEST CONFIGURATION........................................................... 26
7 APPENDIX - INFORMATION ON THE TESTING LABORATORIES.................................... 29

Report No.: RM920221R04A 3Issued: Mar. 14, 2003
Reference No.: RM920221R04
1 CERTIFICATION
PRODUCT: 2.4GHz wireless PCI
MODEL NO: F5D7000
BRAND NAME: Belkin
APPLICANT: Belkin Corporation
STANDARDS: EN 301 489-1 (09-2001), EN 301 489-17 (09-2000)
EN 55022:1998, Class B
EN 61000-4-2:1995
EN 61000-4-3:1995
We, Advance Data Technology Corporation, hereby certify that one sample of the
designation has been tested in our facility from Feb. 27 ~ Mar. 7, 2003. The test
record, data evaluation and Equipment Under Test (EUT) configurations represented
herein are true and accurate accounts of the measurements of the sample's immunity
characteristics under the conditions herein specified.

Report No.: RM920221R04A 4Issued: Mar. 14, 2003
Reference No.: RM920221R04
2 SUMMARY OF TEST RESULTS
The EUT has been tested according to the following specifications:
EMISSION
Standard Test Type Result Remarks
Conducted Test PASS
Meet the requirement of limit
Minimum passing margin is
–23.49dBuV/m at 0.255MHz
EN 55022:1998,
Class B (Conducted
Emission) Radiated Test NA NOT APPLICABLE
EN 61000-3-2:1995
+A1:1998+A2:1998, Class
A
Harmonic current
emissions NA NOT APPLICABLE
EN 61000-3-3:1995 Voltage fluctuations &
flicker NA NOT APPLICABLE
IMMUNITY
Standard Test Type Result Remarks
EN 61000-4-2:1995 Electrostatic discharge
immunity test PASS Meets the requirements of Performance Criterion A
EN 61000-4-3:1995
Radiated, radio-
frequency,
electromagnetic field
immunity test
PASS Meets the requirements of
Performance Criterion A
EN 61000-4-4:1995 Electrical fast transient
/ burst immunity test. NA NOT APPLICABLE
EN 61000-4-5:1995 Surge immunity test NA NOT APPLICABLE
EN 61000-4-6:1996
Immunity to conducted
disturbances, induced
by radio-frequency
fields
NA NOT APPLICABLE
EN 61000-4-11:1994
Voltage dips, short
interruptions and
voltage variations
immunity tests
NA NOT APPLICABLE
NOTE:Please refer to Item 3.3 for more detailed description.

Report No.: RM920221R04A 5Issued: Mar. 14, 2003
Reference No.: RM920221R04
3 GENERAL INFORMATION
3.1 GENERAL DESCRIPTION OF EUT
PRODUCT 2.4GHz wireless PCI
MODEL NO. F5D7000
POWER SUPPLY 3.3VDC from host equipment
MODULATION TYPE DSSS, OFDM
TRANSFER RATE Up to 54Mbps
OPERATING
FREQUENCY 2.412GHz ~ 2.472GHz
NUMBER OF CHANNEL 13
CHANNEL SPACING 5 MHz
RATED RF OUTPUT
POWER LEVEL
18.69dBm (Measured Max. Average)
22.87dBm (Measured Max. Peak))
ANTENNA TYPE Dipole Antenna
DATA CABLE NA
I/O PORTS NA
ASSOCIATED DEVICES NA
NOTE: For a more detailed features description, please refer to the manufacturer's specifications
or User's Manual.

Report No.: RM920221R04A 6Issued: Mar. 14, 2003
Reference No.: RM920221R04
.
3.2 DESCRIPTION OF TEST MODE
The EUT was tested under following conditions:
CONDITION CONFIGURATION REMARKS
1 Transmission
2 Standby
3.3 GENERAL DESCRIPTION OF APPLIED STANDARD
The EUT is a kind of computer peripheral with wireless data transmission function.
According to the specifications of the manufacturer, it must comply with the
requirements of the following standards:
EN 301 489-1 (09-2001), EN 301 489-17 (09-2001)
EN 55022:1998, Class B (Conducted Emission)
EN 61000-4-2:1995
EN 61000-4-3:1995
According to clause 7.1 (table 2) and clause 7.2 (table 3) of EN 301 489-1 (09-2001),
all tests have been performed and recorded as per the above standards.

Report No.: RM920221R04A 7Issued: Mar. 14, 2003
Reference No.: RM920221R04
3.4 DESCRIPTION OF SUPPORT UNIT
The EUT has been tested as an independent unit together with other necessary
accessories or support units. The following support units or accessories were used to
form a representative test configuration during the tests.
For Conducted Emission
NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID
1 PERSONAL
COMPUTER
HP DTPC-16 NA FCC DOC APPROVED
2 MONITOR ADI CM100 020058T102001
82
FCC DOC APPROVED
3 PS/2 KEYBOARD BTC 5121W A00800777 E5XKB5121WTH0110
4 PS/2 MOUSE LOGITECH M-S61 HCA12605710 JNZ211403
5 MODEM ACEEX 1414 980020539 IFAXDM1414
6 PRINTER EPSON LQ-300+ DCGY017059 FCC DOC APPROVED
NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS
1NA
2 1.8 m braid shielded wire, terminated with VGA connector via metallic frame, w/o core
3 1.6 m foil shielded wire, terminated with PS/2 connector via metallic frame, w/o core.
4 1.8 mNon shielded wire, terminated with PS/2 connector via drain wire, w/o core.
5 1.2 m braid shielded wire, terminated with DB25 and DB9 connector via metallic frame, w/o
core.
6 1.2m braid shielded wire, terminated with DB25 and Centronics connector via metallic
frame, w/o core
For EMS
NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID
1 PERSONAL
COMPUTER
HP DTPC-16 NA FCC DOC APPROVED
2 MONITOR DELL E772f NA NA
3 PS/2 KEYBOARD HP 6511-PK 99P468101CY1
W06S012293
FCC DOC APPROVED
4 PS/2 MOUSE HP M-S48a LZE11308376AW JNZ201213
5 MODEM GVC F-1128V1R6 96-191-113003 DK4F1128VR6
6 PRINTER HP 2225C 2931S53817 DSI6XU2225
7 ACCESS POINT D-Link DWL-2000AP NA NA
NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS
1NA
2 1.8 m braid shielded wire, terminated with VGA connector via metallic frame, with core
3 1.8 m foil shielded wire, terminated with PS/2 connector via metallic frame, w/o core
4 1.8 m Non shielded wire, terminated with PS/2 connector via drain wire, w/o core.
5 1.2 m braid shielded wire, terminated with DB25 and DB9 connector via metallic frame,
w/o core.
6 1.2m braid shielded wire, terminated with DB25 and Centronics connector via metallic
frame, w/o core.
7NA
NOTE:All power cords of the above support units are non shielded (1.8m).

Report No.: RM920221R04A 8Issued: Mar. 14, 2003
Reference No.: RM920221R04
4 EMISSION TEST
4.1 CONDUCTED EMISSION MEASUREMENT
4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT
Class A (dBuV) Class B (dBuV)
FREQUENCY
(
MHz
)
Quasi-peak Avera
g
eQuasi-peak Average
0.15 - 0.5 79 66 66 - 56 56 - 46
0.50 - 5.0 73 60 56 46
5.0 - 30.0 73 60 60 50
NOTE: (1) The lower limit shall apply at the transition frequencies.
(2) The limit decreases in line with the logarithm of the frequency in the range of 0.15
to 0.50 MHz.
(3) All emanations from a class A/B digital device or system, including any network of
conductors and apparatus connected thereto, shall not exceed the level of field
strengths specified above.
4.1.2 TEST INSTRUMENTS
DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. CALIBRATED UNTIL
ROHDE & SCHWARZ Test Receiver ESHS30 828109/007 July 03, 2003
ROHDE & SCHWARZ Artificial
Mains Network (for EUT) ESH3-Z5 839135/006 July 02. 2003
* ROHDE & SCHWARZ
4-wire ISN ENY41 838119/028 Nov. 29, 2003
* ROHDE & SCHWARZ
2-wire ISN ENY22 837497/016 Nov. 29, 2003
EMCO-L.I.S.N. (for peripheral) 3825/2 9204-1964 July 02, 2003
Software Cond-V2M1 NA NA
RF cable (JYEBAO) 5D-FB Cable-C02.01 July 5, 2003
HP Terminator (For EMCO LISN) 11593A E1-01-298 Feb. 23, 2004
HP Terminator (For EMCO LISN) 11593A E1-01-299 Feb. 23, 2004
NOTE: 1. The calibration interval of the above test instruments is 12 months and the
calibrations are traceable to NML/ROC and NIST/USA.
2. “*”: These equipment are used for conducted telecom port test only (if tested).
3. The test was performed in ADT Shielded Room No. 2.
4. The VCCI Site Registration No. is C-240.

Report No.: RM920221R04A 9Issued: Mar. 14, 2003
Reference No.: RM920221R04
4.1.3 TEST PROCEDURES
a. The EUT was placed 0.4 meters from the conducting wall of the shielded room
with EUT being connected to the power mains through a line impedance
stabilization network (LISN). Other support units were connected to the power
mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling
impedance for the measuring instrument.
b. Both lines of the power mains connected to the EUT were checked for maximum
conducted interference.
c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels
over 10dB under the prescribed limits could not be reported
4.1.4 DEVIATION FROM TEST STANDARD
No deviation

Report No.: RM920221R04A 10 Issued: Mar. 14, 2003
Reference No.: RM920221R04
4.1.5 TEST SETUP
For the actual test configuration, please refer to the related item – Photographs of the
Test Configuration.
4.1.6 EUT OPERATING CONDITIONS
a. Connected the EUT to a computer system placed on a testing table.
b. The computer system ran a test program to enable EUT under
transmission/receiving condition continuously at specific channel
frequency.
c. The computer system sent "H" messages to its screen.
d. The computer system sent “H” messages to modem.
e. The computer system sent "H" messages to printer and the printer prints
them on paper.

Report No.: RM920221R04A 11 Issued: Mar. 14, 2003
Reference No.: RM920221R04
4.1.7 TEST RESULTS
EUT 2.4GHz wireless PCI Model F5D7000
6dB BANDWIDTH 10 kHz
INPUT POWER 230Vac, 50 Hz PHASE Line (L)
ENVIRONMENTAL
CONDITIONS
22 deg. C, 68 % RH,
1005 hPa
TESTED BY: Cody Chang
Freq. Corr. Reading Value Emission
Level Limit Margin
No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB)
[MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
10.255 0.10 33.16 -33.26 -61.59 51.59 -28.33 -
20.385 0.10 29.89 -29.99 -58.17 48.17 -28.18 -
30.767 0.10 26.86 -26.96 -56.00 46.00 -29.04 -
40.894 0.10 27.21 -27.31 -56.00 46.00 -28.69 -
51.402 0.10 29.45 -29.55 -56.00 46.00 -26.45 -
67.103 0.46 26.08 -26.54 -60.00 50.00 -33.46 -
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. "-": The Quasi-peak reading value also meets average limit and measurement with
the average detector is unnecessary.
3. The emission levels of other frequencies were very low against the limit.
4. Margin value = Emission level - Limit value
5. Correction factor = Insertion loss + Cable loss
6. Emission Level = Correction Factor + Reading Value.

Report No.: RM920221R04A 12 Issued: Mar. 14, 2003
Reference No.: RM920221R04
EUT 2.4GHz wireless PCI Model F5D7000
6dB BANDWIDTH 10 kHz
INPUT POWER 230Vac, 50 Hz PHASE Neutral (N)
ENVIRONMENTAL
CONDITIONS
22 deg. C, 68 % RH,
1005 hPa
TESTED BY: Cody Chang
Freq. Corr. Reading Value Emission
Level Limit Margin
No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB)
[MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV.
10.255 0.10 38.00 -38.10 -61.59 51.59 -23.49 -
20.384 0.10 33.92 -34.02 -58.19 48.19 -24.17 -
30.768 0.10 26.09 -26.19 -56.00 46.00 -29.81 -
40.894 0.10 28.17 -28.27 -56.00 46.00 -27.73 -
51.404 0.10 29.69 -29.79 -56.00 46.00 -26.21 -
67.427 0.36 28.20 -28.56 -60.00 50.00 -31.44 -
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. "-": The Quasi-peak reading value also meets average limit and measurement with the
average detector is unnecessary.
3. The emission levels of other frequencies were very low against the limit.
4. Margin value = Emission level - Limit value
5. Correction factor = Insertion loss + Cable loss
6. Emission Level = Correction Factor + Reading Value.

Report No.: RM920221R04A 13 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5 IMMUNITY TEST
5.1 GENERAL DESCRIPTION
Product
Standard EN 301 489-1 (09-2001), EN 301 489-17 (09-2000)
EN 61000-4-2 Electrostatic Discharge – ESD:
8kV air discharge, 4kV Contact discharge,
Performance Criterion B
Basic Standard,
Specification, and
Performance
Criterion required
EN 61000-4-3 Radio-Frequency Electromagnetic Field
Susceptibility Test – RS:
80-1000 / 1400-2000 MHz, 3V/m, 80% AM (1kHz),
Performance Criterion A
5.2 GENERAL PERFORMANCE CRITERIA DESCRIPTION
The Requirement of Performance Criteria
1
Performance criteria for
continuous phenomena applied
to transmitters (CT)
Criterion A of the applicable class shall apply
2
Performance criteria for
transient phenomena applied to
transmitters (TT)
Criterion B of the applicable class shall apply
3
Performance criteria for
continuous phenomena applied
to receivers (CR)
Criterion A of the applicable class shall apply
4
Performance criteria for
transient phenomena applied to
receivers (TR)
Criterion B of the applicable class shall apply

Report No.: RM920221R04A 14 Issued: Mar. 14, 2003
Reference No.: RM920221R04
The phenomena allowed during and after test in each criterion are clearly stated in
the following table
Performance criteria
Criteria During test After test
A
Shall operate as intended.
May show degradation of
performance (see note1).
Shall be no loss of function.
Shall be no unintentional
transmissions.
Shall operate as intended.
Shall be no degradation of
performance (see note 2).
Shall be no loss of function.
Shall be no loss of stored data or
user programmable functions.
B
May show loss of function (one or
more).
May show degradation of
performance (see note 1).
No unintentional transmissions.
Functions shall be self-
recoverable.
Shall operate as intended after
recovering.
Shall be no degradation of
performance (see note 2).
Shall be no loss of stored data or
user programmable functions.
C
May be loss of function (one or more). Functions shall be recoverable
by the operator.
Shall operate as intended after
recovering.
Shall be no degradation of
performance (see note 2).
NOTE 1:Degradation of performance during the test is understood as a degradation to a level
not below a minimum performance level specified by the manufacturer for the use of
the apparatus as intended. In some cases the specified minimum performance level
may be replaced by a permissible degradation of performance.
If the minimum performance level or the permissible performance degradation is not
specified by the manufacturer then either of these may be derived from the product
description and documentation (including leaflets and advertising) and what the user
may reasonably expect from the apparatus if used as intended.
NOTE 2: No degradation of performance after the test is understood as no degradation below a
minimum performance level specified by the manufacturer for the use of the
apparatus as intended. In some cases the specified minimum performance level may
be replaced by a permissible degradation of performance. After the test no change of
actual operating data or user retrievable data is allowed.
If the minimum performance level or the permissible performance degradation is not
specified by the manufacturer then either of these may be derived from the product
description and documentation (including leaflets and advertising) and what the user
may reasonably expect form the apparatus if used as intended.

Report No.: RM920221R04A 15 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5.3 EUT OPERATING CONDITION
1. Connected the EUT to a computer system placed on a testing table.
2. The computer system ran a test program to enable all functions of EUT.
3. Prepared the access point and placed it outside of testing area to act as
communication partner for EUT.
4. Sent data to EUT by command "PIN" from the communication partner.
Note: For standby mode test, connected a coupling antenna to a spectrum analyzer and placed the
antenna near the EUT to monitor any unintentional response occurring from the EUT during the test.

Report No.: RM920221R04A 16 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5.4 ELECTROSTATIC DISCHARGE IMMUNITY TEST (ESD)
5.4.1 TEST SPECIFICATION
Basic Standard: EN 61000-4-2
Discharge Impedance: 330 ohm / 150 pF
Discharge Voltage: Air Discharge - 8 kV (Direct)
Contact Discharge – 4kV (Direct/Indirect)
Polarity: Positive & Negative
Number of Discharge: Minimum 20 times at each test point
Discharge Mode: Single Discharge
Discharge Period: 1 second minimum
5.4.2 TEST INSTRUMENT
DESCRIPTION &
MANUFACTURER MODEL NO. SERIAL NO. CALIBRATED UNTIL
KeyTek, ESD Simulator MZ-15/EC 9902287 Feb. 26, 2003
EM Test ESD Simulator ESD 30C 0201-28 Jul. 15, 2003
EM Test ESD Discharge Unit P30C 0201-28 Jul. 15, 2003
EM Test ESD Discharge Unit P30C-RFCI 0601-07 Jul. 15, 2003
FCC Coupling Decoupling
Network FCC-801-T2 020022 Jun.12, 2003
FCC Coupling Decoupling
Network FCC-801-T4 020033 Jun.12, 2003
NOTE: 1. The test was performed in ESD Room No. 1.
2. The calibration interval of the above test instruments is 12 months and the
calibrations are traceable to NML/ROC and NIST/USA.

Report No.: RM920221R04A 17 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5.4.3 TEST PROCEDURE
a. Electrostatic discharges were applied only to those points and surfaces of the
EUT that are accessible to users during normal operation.
b. The test was performed with at least ten single discharges on the pre-selected
points in the most sensitive polarity.
c. The time interval between two successive single discharges was at least 1
second.
d. The ESD generator was held perpendicularly to the surface to which the
discharge was applied and the return cable was at least 0.2 meters from the
EUT.
e. Contact discharges were applied to the non-insulating coating, with the pointed
tip of the generator penetrating the coating and contacting the conducting
substrate.
f. Air discharges were applied with the round discharge tip of the discharge
electrode approaching the EUT as fast as possible (without causing
mechanical damage) to touch the EUT. After each discharge, the ESD
generator was removed from the EUT and re-triggered for a new single
discharge. The test was repeated until all discharges were complete.
g. At least ten single discharges (in the most sensitive polarity) were applied to
the Horizontal Coupling Plane at points on each side of the EUT. The ESD
generator was positioned vertically at a distance of 0.1 meters from the EUT
with the discharge electrode touching the HCP.
h. At least ten single discharges (in the most sensitive polarity) were applied to
the center of one vertical edge of the Vertical Coupling Plane in sufficiently
different positions that the four faces of the EUT were completely illuminated.
The VCP (dimensions 0.5m x 0.5m) was placed vertically to and 0.1 meters
from the EUT.
5.4.4 DEVIATION FROM TEST STANDARD
No deviation

Report No.: RM920221R04A 18 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5.4.5 TEST SETUP
PS
PSPS
PS
EUT
Vertical
coupling plane
0.5mm Isolation Support
ESD
Generator
Nearest
Wall Horizontal
coupling plane
R
e
f
e
r
e
n
ce
G
r
ou
n
d
Plan
e
0.1m
1m
470k
X4
80cm
For the actual test configuration, please refer to the related item – Photographs of the
Test Configuration.
NOTE:
TABLE-TOP EQUIPMENT
The configuration consisted of a wooden table 0.8 meters high standing on the Ground Reference
Plane. The GRP consisted of a sheet of aluminum at least 0.25mm thick, and 2.5 meters square
connected to the protective grounding system. A Horizontal Coupling Plane (1.6m x 0.8m) was placed
on the table and attached to the GRP by means of a cable with 940kΩtotal impedance. The equipment
under test, was installed in a representative system as described in section 7 of EN 61000-4-2:1995,
and its cables were placed on the HCP and isolated by an insulating support of 0.5mm thickness. A
distance of 1-meter minimum was provided between the EUT and the walls of the laboratory and any
other metallic structure.

Report No.: RM920221R04A 19 Issued: Mar. 14, 2003
Reference No.: RM920221R04
5.4.6 TEST RESULT
EUT 2.4GHz wireless PCI MODEL NO. F5D7000
MODE Transmission INPUT POWER
(SYSTEM)
230Vac, 50 Hz
ENVIRONMENTAL
CONDITIONS
23 deg.C, 47 % RH
1005 hPa
TESTED BY: Cody Chang
TEST RESULTS OF DIRECT APPLICATION
Discharge
Level (kV)
Polarity
(+/-) Test Point Contact
Discharge Air Discharge Performance Criterion
2, 4 +/- 1, 2 NOTE NA A
2, 4, 8 +/- 3 NA NOTE A
Description of test point:
1.breaket 2. Metal of Antenna connector 3.Antenna
TEST RESULTS OF INDIRECT APPLICATION
Discharge
Level (kV)
Polarity
(+/-) Test Point Horizontal
Coupling Plane
Vertical
Coupling
Plane
Performance
Criterion
2, 4 +/- 1 ~ 4 NOTE NOTE A
Description of test point:
1. Front side 2. Rear side 3. Right side 4. Left side
NOTE:
There was no change compared with the initial operation during and after the test. No unintentional
response was found during the test.

Report No.: RM920221R04A 20 Issued: Mar. 14, 2003
Reference No.: RM920221R04
EUT 2.4GHz wireless PCI MODEL NO. F5D7000
MODE Standby INPUT POWER
(SYSTEM)
230Vac, 50 Hz
ENVIRONMENTAL
CONDITIONS
23 deg.C, 47 % RH
1005 hPa
TESTED BY: Cody Chang
TEST RESULTS OF DIRECT APPLICATION
Discharge
Level (kV)
Polarity
(+/-) Test Point Contact
Discharge Air Discharge Performance Criterion
2, 4 +/- 1, 2 NOTE NA A
2, 4, 8 +/- 3 NA NOTE A
Description of test point:
1.breaket 2. Metal of Antenna connector 3.Antenna
TEST RESULTS OF INDIRECT APPLICATION
Discharge
Level (kV)
Polarity
(+/-) Test Point Horizontal
Coupling Plane
Vertical
Coupling
Plane
Performance
Criterion
2, 4 +/- 1 ~ 4 NOTE NOTE A
Description of test point:
1. Front side 2. Rear side 3. Right side 4. Left side
NOTE:
There was no change compared with the initial operation during and after the test. No unintentional
response was found during the test.