Belkin F5D7000CE1 Service manual

Report No.: RE920221R04A 1 Issued: Mar. 14, 2003
Reference No.: RE920221R04
RADIO TEST REPORT
REPORT NO.: RE920221R04A
MODEL NO.: F5D7000
RECEIVED: Feb. 21, 2003
TESTED: Feb. 20~ Feb. 24, 2003
APPLICANT: Belkin Corporation
ADDRESS:501 WEST WALNUT STREET COMPTON,
CA 90220
ISSUED BY: Advance Data Technology Corporation
LAB LOCATION: No. 47 14th Ling, Chia Pau Tsuen, Linkou
Hsiang, Taipei, Taiwan, R.O.C.
This test report consists of 54 pages in total. It may be duplicated completely for legal use
with the approval of the applicant. It should not be reproduced except in full, without the
written approval of our laboratory. The client should not use it to claim product endorsement
by NVLAP or any U.S. government agencies. The test results in the report only apply to the
tested sample.
0528
ILAC MRA

Report No.: RE920221R04A 2 Issued: Mar. 14, 2003
Reference No.: RE920221R04
TABLE OF CONTENTS
1. CERTIFICATION ....................................................................................................................... 4
2. GENERAL INFORMATION ....................................................................................................... 5
2.1 GENERAL DESCRIPTION OF EUT ..........................................................................................5
2.2 DESCRIPTION OF TEST MODES ............................................................................................6
2.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................................................6
2.4 DESCRIPTION OF SUPPORT UNITS ......................................................................................7
2.5 CONFIGURATION OF SYSTEM UNDER TEST .......................................................................7
2.6 LIST OF MEASUREMENTS ......................................................................................................8
3. TEST PROCEDURES AND RESULTS..................................................................................... 9
TRANSMITTER PARAMETERS ..............................................................................................................9
3.1 EFFECTIVE RADIATED POWER (RADIATED)........................................................................9
3.1.1 LIMITS OF EFFECTIVE RADIATED POWER ...........................................................................9
3.1.2 TEST PROCEDURES................................................................................................................9
3.1.3 DEVIATION FROM TEST STANDARD......................................................................................9
3.1.4 TEST SETUP .............................................................................................................................9
3.1.5 TEST RESULTS (A) .................................................................................................................10
3.1.6 TEST RESULTS (B) .................................................................................................................11
3.2 EFFECTIVE RADIATED POWER (CONDUCTED) .................................................................12
3.2.1 LIMITS OF EFFECTIVE RADIATED POWER .........................................................................12
3.2.2 TEST PROCEDURES..............................................................................................................12
3.2.3 DEVIATION FROM TEST STANDARD....................................................................................12
3.2.4 TEST SETUP ...........................................................................................................................12
3.2.5 TEST RESULTS (A) .................................................................................................................13
3.2.6 TEST RESULTS (B) .................................................................................................................14
3.3 PEAK POWER DENSITY (DSSS EQUIPMENT) (RADIATED)...............................................15
3.3.1 LIMIT OF PEAK POWER DENSITY ........................................................................................15
3.3.2 TEST PROCEDURES..............................................................................................................15
3.3.3 DEVIATION FROM TEST STANDARD....................................................................................15
3.3.4 TEST SETUP ...........................................................................................................................15
3.3.5 TEST RESULTS (A) .................................................................................................................16
3.3.6 TEST RESULTS (B) .................................................................................................................17
3.4 PEAK POWER DENSITY (DSSS EQUIPMENT) (CONDUCTED) ..........................................18
3.4.1 LIMIT OF PEAK POWER DENSITY ........................................................................................18
3.4.2 TEST PROCEDURES..............................................................................................................18
3.4.3 DEVIATION FROM TEST STANDARD....................................................................................18
3.4.4 TEST SETUP ...........................................................................................................................18
3.4.5 TEST RESULTS (A) .................................................................................................................19
3.4.6 TEST RESULTS (B) .................................................................................................................20
3.5 FREQUENCY RANGE (DSSS EQUIPMENT) (RADIATED) ...................................................21
3.5.1 LIMIT OF FREQUENCY RANGE.............................................................................................21
3.5.2 TEST PROCEDURES..............................................................................................................21
3.5.3 DEVIATION FROM TEST STANDARD....................................................................................21
3.5.4 TEST SETUP ...........................................................................................................................21
3.5.5 TEST RESULTS (A) .................................................................................................................22
3.5.6 TEST RESULTS (B) .................................................................................................................24
3.6 FREQUENCY RANGE (DSSS EQUIPMENT) (CONDUCTED) ..............................................26
3.6.1 LIMIT OF FREQUENCY RANGE.............................................................................................26

Report No.: RE920221R04A 3 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.6.2 TEST PROCEDURES..............................................................................................................26
3.6.3 DEVIATION FROM TEST STANDARD....................................................................................26
3.6.4 TEST SETUP ...........................................................................................................................26
3.6.5 TEST RESULTS (A) .................................................................................................................27
3.6.6 TEST RESULTS (B) .................................................................................................................29
3.7 TRANSMITTER SPURIOUS EMISSIONS (RADIATED).........................................................31
3.7.1 LIMITS OF TRANSMITTER SPURIOUS EMISSIONS ............................................................31
3.7.2 TEST PROCEDURES..............................................................................................................31
3.7.3 DEVIATION FROM TEST STANDARD....................................................................................31
3.7.4 TEST SETUP ...........................................................................................................................31
3.7.5 TEST RESULTS.......................................................................................................................32
3.7.6 TEST RESULTS (A) .................................................................................................................33
3.7.7 TEST RESULTS (B) .................................................................................................................37
3.8 TRANSMITTER SPURIOUS EMISSIONS (CONDUCTED) ....................................................41
3.8.1 LIMITS OF TRANSMITTER SPURIOUS EMISSIONS ............................................................41
3.8.2 TEST PROCEDURES..............................................................................................................41
3.8.3 DEVIATION FROM TEST STANDARD....................................................................................41
3.8.4 TEST SETUP ...........................................................................................................................41
3.8.5 TEST RESULTS (A) .................................................................................................................42
3.8.6 TEST RESULTS (B) .................................................................................................................44
RECEIVER PARAMETERS....................................................................................................................46
3.9 RECEIVER SPURIOUS RADIATION (RADIATED).................................................................46
3.9.1 LIMIT OF RECEIVER SPURIOUS RADIATION ......................................................................46
3.9.2 TEST PROCEDURES..............................................................................................................46
3.9.3 DEVIATION FROM TEST STANDARD....................................................................................46
3.9.4 TEST SETUP ...........................................................................................................................46
3.9.5 TEST RESULTS.......................................................................................................................47
3.9.6 TEST RESULTS (A) .................................................................................................................48
3.9.7 TEST RESULTS (B) .................................................................................................................49
3.10 RECEIVER SPURIOUS RADIATION (CONDUCTED)............................................................50
3.10.1 LIMIT OF RECEIVER SPURIOUS RADIATION ......................................................................50
3.10.2 TEST PROCEDURES..............................................................................................................50
3.10.3 DEVIATION FROM TEST STANDARD....................................................................................50
3.10.4 TEST SETUP ...........................................................................................................................50
3.10.5 TEST RESULTS.......................................................................................................................51
4. PHOTOGRAPHS OF THE TEST CONFIGURATION............................................................. 53
5. INFORMATION ON THE TESTING LABORATORIES ........................................................... 54

Report No.: RE920221R04A 4 Issued: Mar. 14, 2003
Reference No.: RE920221R04
1. CERTIFICATION
PRODUCT : 2.4GHz wireless PCI
MODEL NO. : F5D7000
BRAND NAME : Belkin
APPLICANT : Belkin Corporation
STANDARDS : EN 300 328-2 (07-2000)
We, Advance Data Technology Corporation, hereby certify that one sample of the
designation has been tested in our facility from Feb. 20~ Feb. 24, 2003. The test
record, data evaluation and Equipment Under Test (EUT) configurations represented
herein are true and accurate accounts of the measurements of the sample's EMC
characteristics under the conditions herein specified.

Report No.: RE920221R04A 5 Issued: Mar. 14, 2003
Reference No.: RE920221R04
2. GENERAL INFORMATION
2.1 GENERAL DESCRIPTION OF EUT
PRODUCT 2.4GHz wireless PCI
MODEL NO. F5D7000
SOURCE VOLTAGE Vnom= 230 Vmin= 207 Vmax= 253
POWER SUPPLY 3.3VDC from host equipment
RATED RF OUTPUT
POWER
18.69dBm (Measured Max. Average)
22.87dBm (Measured Max. Peak)
MODULATION TYPE CCK, QPSK, DBPSK (DSSS), OFDM
BIT RATE OF
TRANSMITTER up to 54Mbps
OPERATING FREQUENCY 2.412GHz ~ 2.472GHz
NUMBER OF CHANNEL 13
CHANNEL SPACING 5MHz
L.O. FREQUENCY VCO freq.=2/3 fundamental freq.
ANTENNA TYPE Dipole antenna
TEMPERATURE RANGE 0℃~ 55℃
DATA CABLE NA
I/O PORTS NA
ASSOCIATED DEVICES NA
NOTE:
1. The EUT operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps.
2. The EUT complies with IEEE 802.11g draft standards, and backwards compatible with IEEE
802.11b products.
3. For more detailed features description, please refer to the manufacturer's specifications or User's
Manual.

Report No.: RE920221R04A 6 Issued: Mar. 14, 2003
Reference No.: RE920221R04
2.2 DESCRIPTION OF TEST MODES
The EUT (2.4GHz wireless PCI) has been tested under operating and standby
condition. Software used to control the EUT for staying in continuous transmitting
and receiving mode is programmed. Channel 1, 7, 10 and 13 are chosen for
testing to fulfill the requirement of frequency spectrum usage in each country.
Two test result were presented in the following sections, test result A is for
transfer rate 11Mbps with CCK technique and test result B is for transfer rate
54Mbps with OFDM technique
2.3 GENERAL DESCRIPTION OF APPLIED STANDARDS
The EUT is a 2.4GHz wireless PCI, according to the specifications of the
manufacturers, it must comply with the requirements of the following standards:
EN 300 328-2 (07-2000)
All tests have been performed and recorded as per the above standards.

Report No.: RE920221R04A 7 Issued: Mar. 14, 2003
Reference No.: RE920221R04
2.4 DESCRIPTION OF SUPPORT UNITS
The EUT has been tested as an independent unit together with other necessary
accessories or support units. The following support units or accessories were used to
form a representative test configuration during the tests.
NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID
1PERSONAL
COMPUTER HP Brio BA410 SG12902766 FCC DoC APPROVED
2 LCD MONITOR ADI LD-522N 1140A1T00100365A FCC DoC APPROVED
3 KEYBOARD BTC 5121W H013001162 E5XKB5121WTH0110
4 PS2 MOUSE HP M-S48a LZC20508276AW JNZ201213
NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS
1NA
2 1.8 m braid shielded wire, terminated with VGA connector via metallic frame, w/o core.
3 1.6 m foil shielded wire, terminated with PS/2 connector via metallic frame, w/o core.
4 1.8 m Non shielded wire, terminated with PS/2 connector via drain wire, w/o core.
NOTE: All power cords of the above support units are non shielded (1.8m).
2.5 CONFIGURATION OF SYSTEM UNDER TEST
PERSONAL PC
EUT
MONITOR
MOUSE KEYBOARD

Report No.: RE920221R04A 8 Issued: Mar. 14, 2003
Reference No.: RE920221R04
2.6 LIST OF MEASUREMENTS
Clause Test Parameter Remarks
TRANSMITTER PARAMETERS
7.2.1 Effective Radiated Power Applicable
7.2.1 Effective Conducted Power Applicable
7.2.2 Peak Power Density (FHSS Equipment) Not Applicable
7.2.2 Peak Power Density
(DSSS Equipment – Radiated) Applicable
7.2.2 Peak Power Density
(DSSS Equipment – Conducted)
Applicable
7.2.3 Frequency Range of Equipment Using FHSS
Modulation
Not Applicable
7.2.4 Frequency Range of Equipment Using Other
Forms Of Modulation
Applicable
See Note 2
7.2.5 Spurious Emissions (Operating – Radiated) Applicable
7.2.5 Spurious Emissions (Standby – Radiated) See Note 1
7.2.5 Spurious Emissions (Operating – Conducted) Applicable
7.2.5 Spurious Emissions (Standby – Conducted) See Note 1
RECEIVER PARAMETERS
9.1 Spurious Emissions (Radiated) Applicable
9.2 Spurious Emissions (Conducted) Applicable
NOTE:
1. The emission of the transmitter on standby mode is equal to that of receiving mode.
2. Additionally, channel 10 was recorded, for showing effective use of frequency spectrum on France.

Report No.: RE920221R04A 9 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3. TEST PROCEDURES AND RESULTS
TRANSMITTER PARAMETERS
3.1 EFFECTIVE RADIATED POWER (RADIATED)
3.1.1 LIMITS OF EFFECTIVE RADIATED POWER
Condition Limit
Under all test conditions Av: 20 dBm / -10 dBW
Pk: 23dBm/-7dBW
3.1.2 TEST PROCEDURES
Please refer to item 7 of the standard.
3.1.3 DEVIATION FROM TEST STANDARD
No deviation
3.1.4 TEST SETUP
The test setup has been constructed as the normal use condition. The EUT has
been connected with PC and placed on the turn table. Controlling software has
been activated to set the EUT on specific status.

Report No.: RE920221R04A 10 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.1.5 TEST RESULTS (A)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 11Mbps Duty cycle of EUT 100 %
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
TRANSMITTER PEAK POWER (dBm)
(CH1)
2412 MHz
(CH7)
2442 MHz
(CH10)
2457 MHz
(CH13)
2472 MHz
TEST CONDITION
PK AV PK AV PK AV PK AV
Tnom(℃)20 Vnom(v) 230 V 11.37 9.26 11.50 10.05 12.65 11.48 14.28 12.78
Vmin(v) 207 V 10.33 7.58 12.16 10.08 12.74 11.05 14.40 12.27
Tmin(℃)0Vmax(v) 253 V 10.33 7.58 12.16 10.08 12.74 11.05 14.40 12.27
Vmin(v) 207 V 6.33 3.46 7.98 5.83 8.76 6.92 10.57 8.32
Tmax(℃)55 Vmax(v) 253 V 6.33 3.46 7.98 5.83 8.76 6.92 10.57 8.32

Report No.: RE920221R04A 11 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.1.6
TEST RESULTS (B)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 54Mbps Duty cycle of EUT 100 %
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
TRANSMITTER PEAK POWER (dBm)
(CH1)
2412 MHz
(CH7)
2442 MHz
(CH10)
2457 MHz
(CH13)
2472 MHz
TEST CONDITION
PK AV PK AV PK AV PK AV
Tnom(℃)20 Vnom(v) 230 V 14.64 9.31 16.68 10.82 17.46 11.66 18.35 12.22
Vmin(v) 207 V 19.61 14.04 22.49 17.17 22.44 18.09 22.87 18.69
Tmin(℃)0Vmax(v) 253 V 19.61 14.04 22.49 17.17 22.44 18.09 22.87 18.69
Vmin(v) 207 V 9.58 4.24 12.64 6.46 12.58 6.37 13.82 7.20
Tmax(℃)55 Vmax(v) 253 V 9.58 4.24 12.64 6.46 12.58 6.37 13.82 7.20

Report No.: RE920221R04A 12 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.2 EFFECTIVE RADIATED POWER (CONDUCTED)
3.2.1 LIMITS OF EFFECTIVE RADIATED POWER
Condition Limit
Under all test conditions Av: 20 dBm / -10 dBW
Pk: 23dBm/-7dBW
3.2.2 TEST PROCEDURES
Please refer to item 7 of the standard.
3.2.3 DEVIATION FROM TEST STANDARD
No deviation
3.2.4 TEST SETUP
The test setup has been constructed as the normal use condition. The EUT has
been connected with PC and placed on the turn table. Controlling software has
been activated to set the EUT on specific status.

Report No.: RE920221R04A 13 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.2.5 TEST RESULTS (A)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 11Mbps Duty cycle of EUT 100 %
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
TRANSMITTER PEAK POWER (dBm)
(CH1)
2412 MHz
(CH7)
2442 MHz
(CH10)
2457 MHz
(CH13)
2472 MHz
TEST CONDITION
PK AV PK AV PK AV PK AV
Tnom(℃)20 Vnom(v) 230 V 9.32 4.61 9.22 5.23 8.30 5.75 8.26 5.05
Vmin(v) 207 V 8.28 2.93 9.88 5.26 8.39 5.32 8.38 4.54
Tmin(℃)0Vmax(v) 253 V 8.28 2.93 9.88 5.26 8.39 5.32 8.38 4.54
Vmin(v) 207 V 4.28 -1.19 5.70 1.01 4.41 1.19 4.55 0.59
Tmax(℃)55 Vmax(v) 253 V 4.28 -1.19 5.70 1.01 4.41 1.19 4.55 0.59

Report No.: RE920221R04A 14 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.2.6
TEST RESULTS (B)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 54Mbps Duty cycle of EUT 100 %
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
TRANSMITTER PEAK POWER (dBm)
(CH1)
2412 MHz
(CH7)
2442 MHz
(CH10)
2457 MHz
(CH13)
2472 MHz
TEST CONDITION
PK AV PK AV PK AV PK AV
Tnom(℃)20 Vnom(v) 230 V 3.92 2.90 5.34 4.97 5.71 5.23 6.43 5.27
Vmin(v) 207 V 11.39 10.13 13.65 13.02 13.19 14.16 13.71 13.01
Tmin(℃)0Vmax(v) 253 V 11.39 10.13 13.65 13.02 13.19 14.16 13.71 13.01
Vmin(v) 207 V 1.36 0.33 3.80 3.11 3.33 2.44 4.40 2.75
Tmax(℃)55 Vmax(v) 253 V 1.36 0.33 3.80 3.11 3.33 2.44 4.40 2.75

Report No.: RE920221R04A 15 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.3 PEAK POWER DENSITY (DSSS EQUIPMENT) (RADIATED)
3.3.1 LIMIT OF PEAK POWER DENSITY
Condition Limit
Under all test conditions
20dBm / 100 KHz (FHSS)
10dBm / 1 MHz (DSSS)
3.3.2 TEST PROCEDURES
Please refer to item 7 of the standard.
3.3.3 DEVIATION FROM TEST STANDARD
No deviation
3.3.4 TEST SETUP
The EUT has been programmed to continuously transmit in certain channel during
test.

Report No.: RE920221R04A 16 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.3.5 TEST RESULTS (A)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 11Mbps
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
Channel
Number
Channel
Frequency
(MHz)
RF Power
(dBm/KHz)
Limit
(dBm/kHz) PASS/FAIL
12415.2401 0.53/1000 10/1000 PASS
72443.3997 1.59/1000 10/1000 PASS
10 2454.0034 2.71/1000 10/1000 PASS
13 2474.4944 2.42/1000 10/1000 PASS
NOTE
1. For equipment using FHSS modulation, the power density shall be limit to –10dBW(100mW) per
100kHz e.i.r.p.
2. For equipment using other types of modulation, the peak power shall be limit to -20dBW(10mW)
per MHz e.i.r.p.

Report No.: RE920221R04A 17 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.3.6 TEST RESULTS (B)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 54Mbps
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
Channel
Number
Channel
Frequency
(MHz)
RF Power
(dBm/KHz)
Limit
(dBm/kHz) PASS/FAIL
12417.0539 1.49/1000 10/1000 PASS
72446.7407 -0.60/1000 10/1000 PASS
10 2461.9411 -0.06/1000 10/1000 PASS
13 2476.8503 0.19/1000 10/1000 PASS
NOTE
1. For equipment using FHSS modulation, the power density shall be limit to –10dBW(100mW) per
100kHz e.i.r.p.
2. For equipment using other types of modulation, the peak power shall be limit to -20dBW(10mW)
per MHz e.i.r.p.

Report No.: RE920221R04A 18 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.4 PEAK POWER DENSITY (DSSS EQUIPMENT) (CONDUCTED)
3.4.1 LIMIT OF PEAK POWER DENSITY
Condition Limit
Under all test conditions
20dBm / 100 KHz (FHSS)
10dBm / 1 MHz (DSSS)
3.4.2 TEST PROCEDURES
Please refer to item 7 of the standard.
3.4.3 DEVIATION FROM TEST STANDARD
No deviation
3.4.4 TEST SETUP
The EUT has been programmed to continuously transmit in certain channel during
test.

Report No.: RE920221R04A 19 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.4.5 TEST RESULTS (A)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 11Mbps
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
Channel
Number
Channel
Frequency
(MHz)
RF Power
(dBm/KHz)
Limit
(dBm/kHz) PASS/FAIL
12415.2378 2.17/1000 10/1000 PASS
72445.3583 2.21/1000 10/1000 PASS
10 2454.5733 2.65/1000 10/1000 PASS
13 2474.4330 2.36/1000 10/1000 PASS
NOTE
1. For equipment using FHSS modulation, the power density shall be limit to –10dBW(100mW) per
100kHz e.i.r.p.
2. For equipment using other types of modulation, the peak power shall be limit to -20dBW(10mW)
per MHz e.i.r.p.

Report No.: RE920221R04A 20 Issued: Mar. 14, 2003
Reference No.: RE920221R04
3.4.6 TEST RESULTS (B)
EUT 2.4GHz wireless PCI Model F5D7000
Modulation bit rate 54Mbps
Environmental
Conditions 20deg. C,66%RH Tested By Hardaway Lee
Channel
Number
Channel
Frequency
(MHz)
RF Power
(dBm/KHz)
Limit
(dBm/kHz) PASS/FAIL
12416.7533 -7.46/1000 10/1000 PASS
72446.8409 -5.121000 10/1000 PASS
10 2461.8033 -7.66/1000 10/1000 PASS
13 2476.9148 -7.741000 10/1000 PASS
NOTE
1. For equipment using FHSS modulation, the power density shall be limit to –10dBW(100mW) per
100kHz e.i.r.p.
2. For equipment using other types of modulation, the peak power shall be limit to -20dBW(10mW)
per MHz e.i.r.p.