Belkin OmniView F1DA104T User manual

13
™
OmniView
PRO2 Series KVM Switch
PRO2 Series
User Manual
F1DA104T
F1DA108T
F1DA11 T

TABLE OF CONTENTS
Overview
Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Equipment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Unit Display Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation
Pre-Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Step-by-Step Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Single PRO2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Connecting Multiple PRO2s (Daisy-Chaining) . . . . . . . . . . . . . . . . . . .12
Powering up the Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using your PRO2
Selecting a Computer Using Keyboard Hot Key Commands . . . . . . . . .17
AutoScan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Selecting a Computer Using Direct-Access Port Selectors . . . . . . . . . . .18
Bank Up and Bank Down Scroll Buttons . . . . . . . . . . . . . . . . . . . . . . .18
On-Screen Display Menu Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Belkin KVM Switches and Accessories
OmniView KVM Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
OmniView All-In-One KVM Cables . . . . . . . . . . . . . . . . . . . . . . . . . . .25
OmniView Accessories and Adapters . . . . . . . . . . . . . . . . . . . . . . . . . .26
PRO2 Series FAQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

1
™
OmniView
Congratulations on your
purchase of this Belkin
OmniView PRO2 Series KVM
Switch (the PRO2). Our diverse
line of KVM solutions exemplifies the Belkin commitment to
delivering high-quality, durable products at a reasonable price. Designed to
give you control over multiple computers and servers from one console,
Belkin PRO2s come in a variety of capacities suitable for all configurations,
large or small.
Belkin has designed and developed this PRO2 with the server administrator
in mind. The result is a KVM Switch that surpasses any other switch on the
market. The PRO2 is engineered to work with the most advanced server room
and laboratory environments, offering intuitive port indicators, direct-access
port selectors, high video resolution support, and flash upgradeable firmware.
The PRO2 also comes with an unparalleled Belkin Five-Year Warranty.
This manual will provide details about your new PRO2, from installation and
operation to troubleshooting—in the unlikely event of a problem.
For quick and easy installation, please refer to the Quick Installation Guide
included in your PRO2 packaging.
Thank you for purchasing the PRO2. We appreciate your business and have
confidence that you will soon see for yourself why over 1 million Belkin
OmniView products are being used worldwide.
Package Contents
• OmniView PRO2 Series KVM Switch
• Adjustable Rack-mount Brackets with Screws
• DB25-to-RJ45 Parallel Flash Cable
• User Manual
• Quick Installation Guide
• 12-Volt DC, 1-Amp Power Supply
• Registration Card
PRO2 Series KVM Switch

2
OVERVIEW
The PRO2s allow you to control up to a maximum of 256 computers with one
keyboard, monitor, and mouse. They support PS/2 input devices (keyboard
and mouse) as well as VGA, SVGA, XGA, and XGA-2 video.
They support both PS/2 and USB output. This enables cross-platform control
over PCs and USB-based computers including USB Sun™workstations and
Mac®computers.
Feature Overview
Hot Keys:
Hot key functionality allows you to select a desired port using designated key
commands. By using a simple hot key sequence on your keyboard, selecting
one computer from as many as 256 computers is instantaneous. For a listing
of complete hot key instructions and commands, see pages 17-19.
AutoScan:
The AutoScan feature allows you to set your PRO2 to scan and monitor the
activities of all operating computers connected to the switch—one by one.
The time interval allotted for each computer can be defined or adjusted
through the On-Screen Display (OSD) menu. For complete instructions on
AutoScan usage, please refer to page 18.
Video Resolution:
Through a 400MHz bandwidth, the PRO2s support video resolutions of up to
2048x1536@85Hz. To preserve signal integrity at these higher resolutions,
your PRO2 requires 75-Ohm coaxial VGA cabling.
Flash Upgrade:
Flash upgradeable firmware allows you to install the latest firmware for your
PRO2. This enables your PRO2 to maintain consistent compatibility with the
latest devices and computers. Firmware upgrades are free for the life of your
PRO2. Refer to the enclosed flash upgrade instruction document or visit us
at belkin.com for complete upgrade information and support.
On-Screen Display (OSD):
The OSD feature simplifies server management by allowing you to assign
individual names to each connected server throughout the system. It provides
a visual means of switching between computers and setting the time interval
for the AutoScan function.

3
OVERVIEW
Front-Panel Push Button:
Direct-access port selectors, located conveniently on the front panel of the
PRO2, allow for simple, manual port-selection. Each button controls a port.
LED Display:
An LED display on the face of the PRO2 serves as a status monitor. An LED
next to each direct-access port selector illuminates to indicate that the console
currently controls the corresponding computer. As a port selector is pushed,
the LED next to it will light up. A flashing port LED indicates that there is no
computer connected to that port.
Seven-Segment LED Display:
When daisy-chaining multiple PRO2s together, the seven-segment LED display
serves as a quick indicator of the selected BANK.
Equipment Requirements
Cables:
To connect to the PRO2, each PS/2 computer requires one VGA cable, one
PS/2 keyboard cable, and one PS/2 mouse cable. Keyboard and mouse cables
must have PS/2 male-to-PS/2 male connectors. Each USB computer requires
one VGA cable and one USB A-to-B cable.
Video resolution support of up to 2048x1536@85Hz requires use of a
75-Ohm coaxial VGA cable to preserve signal integrity. VGA cables must
have HDDB15 female-to-HDDB15 male connectors.
Belkin highly recommends that you use OmniView All-In-One PRO Series
Plus or Gold Series Cables. These cables offer the highest quality possible to
ensure optimal data transmission. All-In-One Cables are molded together for
a clean and organized setup; are double-shielded to reduce EMI/RFI
interference; have strain-relief construction for added durability; come with a
ferrite bead for noise immunity; and include PC99 color-coded connectors for
easy identification and connection. The PRO Series Plus Cables include an
industry-standard, 14-pin, coaxial VGA cable and nickel-plated connectors
for high-resolution applications. The Gold Series Cables have a custom,
15-pin, coaxial VGA cable and gold-plated connectors for superior clarity,
connectivity, and error-free data transmission. OmniView Cables are

4
available in both USB and PS/2 connector types. The following cables are
recommended for your PRO2:
OmniView All-In-One PRO Series Plus
F3X1105-XX (PS/2 Style)
F3X1962-XX (USB Style)
OmniView All-In-One Gold Series
F3X1835-XX-GLD (PS/2 Style)
F3X1895-XX-GLD (USB Style)
(-XX denotes length in feet)
Operating Systems
OmniView PRO2 Series KVM Switches are for use on CPUs using:
Platforms:
• Windows®95/98/2000/Me/NT®/XP
• DOS
• Turbolinux®and all Linux®distributions
• Novell®NetWare®4.x/5.x
• Mac (with USB support)
• Sun (with USB support)
Keyboards:
• Supports 101-/102-/104-key keyboards
Mice:
• Microsoft®system-compatible PS/2 or PS/2 & USB combo mice
(with PS/2 adapter) having 2, 3, 4, or 5 buttons
• Microsoft system-compatible PS/2 wireless or optical mice
Monitor:
• VGA
• SVGA
• MultiSync®
OVERVIEW
USB Style
PS/2 Style

5
OVERVIEW
Side View of the PRO2:
BANK DIP switch
(may be located on the
back in some models)
BANK 1
ON ON
23456 1234 FLASH
FLASH DIP switch
(may be located on the back
in some models)
F1DA108T

6
OVERVIEW
USB
USB
04
03
Direct-access
port selector
LED for selected
port identification
Manual BANK
scroll buttons
7-segment LED for
selected BANK identification
AutoScan button
Master Input/Slave Output
Console VGA Computer VGA port
Console PS/2 mouse/keyboard ports
Computer PS/2
mouse/keyboard ports
Computer USB port
DC power jack
Flash upgrade port
Slave Input
Back View of the PRO2:
F1DA108T
F1DA108T
Front View of the PRO2:

7
OVERVIEW
Specifications
Part No.: F1DA104T, F1DA108T & F1DA116T
Power: 12-Volt DC, 1-Amp power adapter with center-pin positive polarity
Daisy-Chain: Maximum of 16 KVM Switches
Computer Connections Supported:
4 (F1DA104T)
8 (F1DA108T)
16 (F1DA116T)
Keyboard Emulation: PS/2
Mouse Emulation: PS/2
Monitors Supported: VGA, SVGA, MultiSync, and LCD (optional adapter may
be required)
Max. Resolution: 2048x1536@85Hz
Bandwidth: 400MHz
Keyboard Input: 6-pin miniDIN (PS/2)
Mouse Input: 6-pin miniDIN (PS/2)
VGA Port: 15-pin HDDB type
Port LED Indicators: 4 (F1DA104T)
8 (F1DA108T)
16 (F1DA116T)
Enclosure: Metal enclosure with high-impact plastic faceplate
Dimensions:
(F1DA104T) 11 x 1.75 x 6 inch (279mm x 44.5mm x 150mm)
(F1DA108T)17.25 x 1.75 x 7.5 inch (438mm x 44.5mm x 190mm)
(F1DA116T) 17.25 x 3.5 x 7.5 inch (438mm x 89mm x 190mm)
Weight:
(F1DA104T) 5.3 lbs. (2414.5 grams)
(F1DA108T) 9.2 lbs. (4181.5 grams)
(F1DA116T) 12 lbs. (5472.5 grams)
Operating Temp.: 32° to 104° F (0~40° C)
Storage Temp.: -4° to 140° F (20~60° C)
Humidity: 0-80% RH, non-condensing
Warranty: 5 years
Note: Specifications are subject to change without notice.

8
Pre-Configuration
Where to Place the PRO2:
The enclosure of the PRO2 is designed for standalone or rack-mount
configuration. The 8- and 16-port PRO2s are natively rack-mountable in
standard 19-inch server racks. Rack-mount hardware is included with these
switches for a study rack installation. An optional rack-mount kit (F1D005) is
available for use with the 4-Port PRO2.
Consider the following when deciding where to place the PRO2:
• whether or not you intend to use the direct-access port selectors;
• the lengths of the cables attached to your keyboard, monitor, and mouse;
• the location of your CPUs in relation to your console;
• and the lengths of the cables you use to connect your computers to the PRO2.
Cable Distance Requirements:
For PS/2 computers:
VGA signals transmit best up to 25 feet. Beyond that length, the
probability of video degradation increases. For this reason, we recommend
that the length of the cables between the PRO2 and the connected computers
does not exceed 25 feet.
Note:
If you need your console to reside further than 25 feet from the PRO2, we
recommend using the Belkin CAT5 Extender (F1D084) with a standard CAT5
UPT cable. By using this device, you may increase the distance between
your PRO2 and your keyboard, mouse, and monitor by as much as 500 feet
without risking signal degradation.
For USB computers:
USB signals can be transmitted up to 15 feet between the PRO2 and the CPU.
Beyond 15 feet, the probability of signal failure is likely, and this may cause
the device to fail.
Cautions and Warnings:
Avoid placing cables near fluorescent lights, air conditioning equipment, or
machines that create electrical noise (e.g., vacuum cleaners).
INSTALLATION

9
INSTALLATION
Step-by-Step Installation Guide
Cautions and Warnings:
Before attempting to connect anything to the PRO2 or your computer(s),
please ensure that everything is powered off. Plugging and unplugging cables
while computer(s) are powered on may cause irreversible damage to the
computer(s) and/or the PRO2(s). Belkin Components is not responsible for
damage caused in this way.
Installing the PRO2 into a Server Rack:
Bracket Installation (F1DA108T and F1DA116T only)
Eight- or 16-Port PRO2s include adjustable mounting brackets ideal for
installation in 19-inch racks. The mounting brackets feature three adjustment
positions to allow the faceplate of the PRO2 to mount flush to your rack-mounted
servers, or to the rack. Please follow these simple steps to achieve the desired
adjustment. The 4-Port PRO2 requires an optional mounting kit (F1D005).
1. Remove the adjustable brackets from the box. (The adjustable brackets
allow you to set the PRO2’s face flush with the ends of the rails or to
extend the PRO2 past the front of the rails).
2. Determine how far you would like the PRO2 to protrude from the rack.
Select a bracket-hole scheme.
3. Attach the bracket to the side of your PRO2 using the Phillips screws
provided. (Refer to diagram above).
4. Mount the PRO2 to the rack rail assembly.
Note: If this PRO2 will be daisy-chained to another PRO2, set the BANK
address prior to installing on a rack. Refer to the section in this user manual
labeled “Connecting Multiple PRO2s (Daisy-Chaining)”.

10
INSTALLATION
Your PRO2 is now mounted securely into the bracket and you are ready to
connect cables to the back of the unit.
Note for Belkin PRO Series owners (F1D104-OSD, F1D108-OSD,
F1D116-OSD): Installation for the PRO has changed. Please follow this
installation manual completely to assure proper installation. Failure to do
so may result in keyboard or mouse errors, and/or faulty operation.
Single PRO2 Installation
This section provides complete instructions for the hardware setup of a single
PRO2. (F1DA104T, F1DA108T, and F1DA116T)
PS/2 Installation:
Keyboard, Video, and Mouse Connections
Connect the Console:
1. Connect the monitor to the
PRO2. Attach your monitor
cable to the HDDB15 female
port on the back of the PRO2
labeled "Console VGA".
2. Connect the PS/2 keyboard
cable to the keyboard port
on the back of the PRO2
in the "Console" section.
3. Connect the PS/2 mouse
cable to the mouse port on
the back of the PRO2 in
the "Console" section.
Attach the power supply to the DC power jack labeled "DC 12V, 1A" located
on the rear of the PRO2. Once the power is connected to a power source, the
LED for port 01 will begin flashing. Sequentially push the direct-access port
selectors for ports 01 through 08 (04 for F1DA104T and 16 for F1DA116T).
The corresponding LED should flash as each button is pressed, indicating that
the port is ready for connecting your servers (computer connection).
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01
123
456
789
+
-
=/
0
num
lock cap lock pgup
return
shift clt
alt
delete
P[]
'"
;:
L
K
=
-
09
8PGUP PG DN
HOME
HELP CAPS `
ESC
<>
^
+
OPT PC
F9 F10 F11
76543
2
1
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01

11
INSTALLATION
Connect the Computer:
PS/2 Installation
1. Using an OmniView KVM Cable (Belkin part# F3X1105-XX or
F3X1835-XX-GLD), plug in the male VGA connector to the VGA port
on the computer. Connect the other end (the female connector) of the
VGA cable to the back of the PRO2 labeled "VGA 01".
2. Connect the PS/2 keyboard and PS/2 mouse connectors of the cable to
the keyboard and mouse ports on the computer. Connect the other ends
of the cables to the keyboard and mouse ports located directly underneath
VGA 01 on the PRO2 (Belkin part # F3X1105-XX or F3X1835-XX-GLD).
3. Repeat steps 1 and 2 for each
additional PS/2 computer you
wish to connect.
USB Installation:
Boot the computer you wish to connect via USB as you would normally with
the keyboard, monitor, and mouse connected directly to the computer. After
the operating system finishes loading, connect the PRO2 to the USB computer
using the USB A-to-B cable that is part of your USB KVM Cable (Belkin part#
F3X1962-XX or F3X1895-XX-GLD). Your computer should recognize your
PRO2 and automatically install the HID USB driver if necessary. Once your
computer finishes installing the USB driver, you can power down your
computer to connect it to the PRO2.
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01

12
INSTALLATION
1. Using a USB KVM Cable (Belkin part# F3X1962-XX or F3X1895-XX-GLD),
plug the male VGA connector into the VGA port on the computer.
Connect the other end (the female connector) of the VGA cable to
the back of the PRO2 for the appropriate port you wish
to connect to (for example, "VGA 02").
2. Connect the
USB cable's
"A-type"
connector to an available USB port on your USB
computer. Connect the other end of the USB cable
(with the "B-type" connector) to the corresponding
port on the back of the PRO2 (for example, "USB 02").
NOTE: We recommend you attach the KVM cable directly to a free USB port
on your computer.
Repeat steps 1 and 2 above for each additional USB computer you wish
to connect.
Connecting Multiple PRO2s (Daisy-Chaining)
You can daisy-chain up to 16 PRO2s together, giving a server administrator
control over a maximum of 256 computers. When daisy-chained together,
each unit is referred to as a "BANK" and assigned an address. The Console
keyboard, mouse, and monitor connects to BANK 00 and is referred to as the
"Master" switch. BANKs 01 through 15 are referred to as "Slave" switches.
Note: A daisy-chain cable (F1D108-CBL) is required to daisy-chain each
PRO2 and is available through your Belkin reseller or online at belkin.com.
All PRO2s feature a “BANK DIP” switch. The BANK DIP switch is used for proper
identification and use of PRO2s in a single-unit or daisy-chain configuration.
• For a single-unit configuration, set the BANK DIP switch on the PRO2 to the
“Master” (BANK address 00) setting. This is the factory default setting.
• For multi-unit configuration, the BANK DIP switch on the Master unit must
be set to “BANK address 00”. Slave units must be set to a unique BANK
address (from 01 through 15). Refer to the chart below for BANK DIP
switch settings.
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01

13
INSTALLATION
BANK DIP Switch Configuration Chart
DIP SWITCH# BANK ADDRESS
123456
ON ON ON ON ON ON BANK 00 MASTER (default)
ON ON OFF ON ON ON BANK 01 SLAVE
ON ON ON OFF ON ON BANK 02 SLAVE
ON ON OFF OFF ON ON BANK 03 SLAVE
ON ON ON ON OFF ON BANK 04 SLAVE
ON ON OFF ON OFF ON BANK 05 SLAVE
ON ON ON OFF OFF ON BANK 06 SLAVE
ON ON OFF OFF OFF ON BANK 07 SLAVE
ON ON ON ON ON OFF BANK 08 SLAVE
ON ON OFF ON ON OFF BANK 09 SLAVE
ON ON ON OFF ON OFF BANK 10 SLAVE
ON ON OFF OFF ON OFF BANK 11 SLAVE
ON ON ON ON OFF OFF BANK 12 SLAVE
ON ON OFF ON OFF OFF BANK 13 SLAVE
ON ON ON OFF OFF OFF BANK 14 SLAVE
ON ON OFF OFF OFF OFF BANK 15 SLAVE
Note: “On” is the down position.
Example:
Four 8-Port PRO2s (F1DA108T) are daisy-chained together for controlling
up to 32 computers. The DIP switch on the Master unit is set to “BANK 00”
(factory default) and the Slave units are each set to a unique BANK
(between 01 and 15).

14
Installation
Before You Begin:
1. Make sure that all computers are powered off and that each PRO2 has
been assigned a unique BANK address.
2. Place Master and Slave switches in the desired location. Make sure all
are turned off and unplugged from the power source.
3. Connect the Console monitor, keyboard, and mouse to the Console
ports of the Master switch or Bank 00, as described previously in this
installation guide.
Connecting the Master Switch to the First Slave Switch:
4. Using the daisy-chain cable (F1D108-CBL), connect one end of the cable
to the “Master Input/Slave Output” port on the Master switch (BANK 00).
5. Connect the other end of the daisy-chain cable to the “Master Input/Slave
Output” port of the first Slave switch (BANK 01).
Adding Additional Slave Units:
6. Using the daisy-chain cable (F1D108-CBL), connect one end of the cable
to the available daisy-chain port labeled “Slave Input” on the Slave switch
(for example, BANK 01).
7. Connect the other end of the daisy-chain cable to the “Master Input/Slave
Output” port of the Slave switch that you are adding
(for example, BANK 02).
8. Repeat steps 6 and 7 for additional PRO2s you wish to
daisy-chain together.
INSTALLATION

15
Example of Daisy-Chain Configuration:
Connecting the Computers:
9. Connect all computers to the Master and Slave switches. Refer to
“Single PRO2 Installation” on page 10 for instruction on how to connect
the Console and the computers to the PRO2.
10. Connect the power supply to the Master switch. Power up the Master
switch. You should see the Master switch light up and display the digits
“00”, indicating its BANK address.
11. Power up the Slave switches sequentially, beginning with Bank 01, by
connecting each unit’s power supply. Each switch should display its
corresponding BANK address number as it is powered up.
Note: If the PRO2s do not enumerate correctly, reset the Master switch
(BANK 00) by simultaneously pressing the "BANK +" and "BANK –" buttons.
You can also reset the Master switch to detect newly added Slave switches.
If the switches still do not enumerate correctly, check that all switches have
the correct BANK address assigned to them and that all daisy-chain cables
are connected properly.
12. Verify that the Master unit has detected all Slave switches by scrolling
through the BANKS using the BANK up and BANK down buttons.
If all Slave switches are detected properly, the LED display on the Master
switch will register and display the attached Slave switch’s BANK address.
INSTALLATION
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01
VGA VGA VGA VGA VGA VGA VGA VGA
VGA
08
08 08
USB
USB USB USB USB
USB
USB
USB
07 07
07 06 06
06
06
05 05
05 04
04
04
03 03
03 02
02
02 01
01
01
S l ave I npu t
M as t e r I npu t /S l ave O u t pu t
S l ave I npu t
M as t e r I npu t /S l ave O u t pu t
S l ave I npu t
M as t e r I npu t /S l ave O u t pu t
S l ave I npu t
M as t e r I npu t /S l ave O u t pu t
cable 1
cable 2
cable 3
Master unit (BANK 00)
Slave unit (BANK 01)
Slave unit (BANK 02)
Slave unit (BANK 03)

16
USING YOUR PRO2
Powering up the Systems
Once all cables have been connected, power up the computers that are
attached to the PRO2. All computers can be powered on simultaneously. The
PRO2 emulates both a mouse and keyboard on each port and allows your
computer to boot normally.
The computer connected to port “1” will be displayed on the monitor. Check
to see that the keyboard, monitor, and mouse are working normally. Proceed
to do this with all occupied ports to verify that all computers are connected
and responding correctly. If you encounter an error, check your cable
connections for that computer and reboot. If the problem persists, please
refer to the Troubleshooting section in this manual.
Using Your PRO2:
Now that you have connected your Console and computers to your PRO2,
it is ready for use.
Select connected computers by either the direct-access port selectors, located on
the front panel of the PRO2, using the On-Screen Display, or by using hot key
commands through the Console keyboard. It takes approximately 1-2 seconds for
the video signal to refresh after switching computers. Re-synchronization of the
mouse and keyboard signals also occurs. This is normal operation and ensures
that proper synchronization is established between the Console and the con-
nected computers.

17
Selecting a Computer Using Keyboard Hot Key Commands:
Switch to the next or previous port with simple keyboard key sequences
using the “Scroll Lock” key and either the up or down arrow keys. To send
commands to the PRO2, the “Scroll Lock” key must be pressed twice within
two seconds. The PRO2 will beep, confirming that it is in hot key mode.
Next, press the up or down arrow keys, and the PRO2 will switch to either
the prior port or the next port.
With a single-switch configuration (no daisy-chained switches), you can
switch directly to any port by entering the two-digit number of the port you
wish to access. For example, if you press “Scroll Lock”, “Scroll Lock”, “02”,
the PRO2 will switch to the computer on port 2 located on BANK 00.
Note: You will have approximately five seconds to complete each
hot key sequence.
With daisy-chain switch configuration, you can switch between BANKs by
pressing “Scroll Lock”, “Scroll Lock”, “Page Up”, to switch to the previous BANK.
Press “Scroll Lock”, “Scroll Lock”, “Page Down”, to switch to the next BANK.
USING YOUR PRO2
Page
Up
Switch to BANK 00, Port 2—(02)
+
Page
Down
+
++ ++
Switch to previous BANK—Page Up Switch to next BANK— Page Down
++
Switch to next active port—Down arrow Switch to previous active port—Up arrow
++

18
USING YOUR KVM SWITCH
With a daisy-chain switch configuration, you can switch directly to any port
on any BANK by pressing “Scroll Lock”, “Scroll Lock”, BANK address, and
port number. For example, if you press “Scroll Lock”, “Scroll Lock”, “03”,
“05”, the computer on BANK 03, Port 5 will become active.
AutoScan Mode:
Pressing the AutoScan button on the PRO2 will activate the AutoScan
function. In AutoScan mode, the PRO2 remains on one port for a pre-set
number of seconds, before switching to the next computer. This time
interval can be adjusted via the On-Screen Display menu.
Note: There is no mouse or keyboard control in AutoScan mode. This is
necessary to prevent data and synchronization errors. If the user is using the
mouse or keyboard when the PRO2 is switching between ports, data flow
may become interrupted and could result in erratic mouse movement and/or
wrong-character input when using the keyboard.
Press any button on the front panel or any key on the keyboard to
disable AutoScan.
Selecting a Computer Using Direct-Access Port Selectors:
You can directly select which computer you wish to control by pressing the
direct-access port selector next to the corresponding port. The LED will illuminate
to indicate the port is currently selected. If you are installing multiple PRO2s that
are daisy-chained, use the BANK scroll keys located on the front panel of the
Master switch to access other computers that are connected to the Slave switches.
BANK Up and BANK Down Scroll Buttons:
Pressing the BANK + and BANK – scroll buttons on the Master switch will
allow you to switch between the daisy-chained PRO2s. Pressing both
buttons simultaneously will reset the PRO2.
The BANK + button will take you to the next BANK. For example, when you
are at the Master switch (BANK 00) and want to check computers on BANK
02, pressing the BANK + button will take you to BANK 02. As a default, the
35
+++