Belkin F1DA108Q User manual

OmniView® PRO3 PS/2
KVM Switch
User Manual
F1DA104Qea
F1DA108Qea
F1DA116Qea

1
Table of Contents
1. Introduction ...................................................................................... 1
Package Contents ......................................................................2
2. Overview .......................................................................................... 3
Feature Overview ........................................................................3
Equipment Requirements ............................................................5
System Requirements .................................................................6
Unit Display Diagrams ................................................................7
Specifications .............................................................................9
3. Installation ......................................................................................10
Pre-Configuration .....................................................................10
Mounting the PRO3 KVM Switch ...............................................11
Connecting the Console to the PRO3 KVM Switch .....................14
Connecting PS/2 Servers to the PRO3 KVM Switch ...................15
Connecting Multiple PRO3 KVM Switches (Daisy-Chaining) .......17
Powering Up the Systems .........................................................22
4. Using your PRO3 KVM Switch ...........................................................23
Selecting a Server or BANK Using Hot-Key Commands .............23
Selecting a Server Using Direct-Access Port Selectors ..............25
Selecting a BANK Using Scroll Buttons .....................................25
AutoScan Mode ........................................................................26
On-Screen Display (OSD) ..........................................................27
Keyboard Hot-Key-Command Shortcuts ....................................31
Updating Firmware ...................................................................32
5. Frequently Asked Questions ............................................................34
6. Troubleshooting ..............................................................................36
7. Glossary ..........................................................................................38
8. Information .....................................................................................39

1
1
2
3
4
5
6
7
8
section
Congratulations on your purchase
of this Belkin OmniView PRO3 PS/2
KVM Switch (the KVM Switch).
Our diverse line of KVM solutions
exemplifies the Belkin commitment
to delivering
high-quality, durable products at an
affordable price.
Belkin has designed and developed this KVM Switch with the server
administrator in mind. The result is a KVM Switch that surpasses any other
switch on the market. The PRO3 KVM Switch is engineered to work with the
most advanced server-room and laboratory environments, offering intuitive port
indicators, direct-access port selectors, high video resolution support, and
flash-upgradeable firmware.
PRO3 KVM Switches can be daisy-chained together easily to enable
management of up to 256 PS/2 servers from a single console. The PRO3 KVM
Switch also comes with an unparalleled Belkin 3-Year Warranty.
This User Manual will provide details about your new PRO3 KVM Switch, from
installation and operation to troubleshooting—in the unlikely event of a problem.
For quick and easy installation, please refer to the Quick Installation Guide
included in your PRO3 KVM Switch packaging.
Thank you for purchasing the Belkin OmniView PRO3 KVM Switch. We
appreciate your business and have confidence that you will soon see for yourself
why Belkin is the number-one-selling brand in KVM switches worldwide.
Introduction

32
32
Package Contents











 

Introduction
12V DC,1A Power Supply
Power Cable with Schuko plug
Power Cable with UK plug
OmniView PRO3KVM
Switch
User Manual
Rack-MountBrackets
withScrews (F1DA108Qea,
F1DA116Qea only)
Quick Installation Guide
DB9-to-RJ11
Serial Flash
Cable

32
1
2
3
4
5
6
7
8
section
32
Overview
Feature Overview
• Hot Keys
Hot-key functionality allows you to select a desired port using designated key
commands. By using a simple hot-key sequence on your keyboard, you can
select one server from as many as 256 servers, instantaneously.
• AutoScan
The AutoScan feature allows you to set your PRO3 KVM Switch to scan and
monitor the activities of all connected servers, one by one. The time interval
allotted for each server can be adjusted through the On-Screen Display
(OSD) menu.
• Video Resolution
The PRO3 KVM Switch supports video resolutions of up to 1920x1440@75Hz.
• Security
Allows you to specify user names and passwords to prevent unauthorized
users from accessing the OSD and KVM Switch.
• Dedicated Daisy-Chain Port
Up to 16 KVM switches can be daisy-chained together using dedicated
ports, so you can easily expand your KVM configuration as your server
environment grows.
• On-Screen Display (OSD)
The OSD feature simplifies server management by allowing you to assign
individual names to each connected server throughout the system. It provides
a visual means of switching between servers and assigning the hot-key
scheme. The OSD can also be set up to support regional languages.
• Front-Panel Push Buttons
Direct-access port selectors, located conveniently on the front panel of the
PRO3 KVM Switch, allow for simple, manual port-selection.

54
54
Overview
• LED Display
An LED display on the front panel of the PRO3 KVM Switch serves as a status
monitor. An LED above each direct-access port selector illuminates to indicate
that the console currently controls the corresponding server. As a port selector
is pushed, the LED above it will light up. A flashing port LED indicates that
there is no server connected to that port.
• 7-Segment LED Display
When daisy-chaining multiple PRO3 KVM Switches together, the 7-segment
LED display serves as a quick indicator of the selected BANK.
• Flash Upgrade
Flash-upgradeable firmware allows you to install the latest firmware on your
PRO3 KVM Switch. This enables your KVM Switch to maintain consistent
compatibility with the latest devices and servers. Firmware upgrades are free
for the life of your PRO3 KVM Switch and can be downloaded from Belkin’s
support website at www.belkin.com/support.

54
1
2
3
4
5
6
7
8
section
54
Overview
Equipment Requirements
Cables:
Connecting the PRO3 KVM Switch to a server requires a Belkin Dual-Port
Micro-Cable Kit.
Belkin Dual-Port Micro-Cable Kits:
F1D9400-XX (PS/2-style)

Belkin PRO3 Daisy-Chain Cable:
F1D108-CBL
(Available in a 2 feet version)

Note: Product codes and availability may vary.

76
76
Overview
System Requirements
OS Platforms
The PRO3 KVM Switch is compatible with CPUs running on, but not limited to,
the following OS platforms:
• Windows® NT®, 2000, XP, Server 2003, or VistaTM
• Microsoft® DOS 5.x and above
• Red Hat® Linux® 8.x and above
• Novell® NetWare® 5.x
Keyboards
• PS/2-compatible
• Supports 101-/102-/104-key keyboards
Mice
• PS/2-compatible mice (with PS/2 adapter)
having 2, 3, 4, or 5 buttons
• PS/2-compatible wireless or optical mice
Monitors
• CRT
• LCD (with VGA support)

76
1
2
3
4
5
6
7
8
section
76
Overview
Unit Display Diagrams
Front View of the PRO3 KVM Switch:
(F1DA108Qea)
 










98
98
Overview
Unit Display Diagrams
Back View of the PRO3 KVM Switch:










98
1
2
3
4
5
6
7
8
section
98
Overview
Specifications
Part No.: F1DA104Qea, F1DA108Qea, F1DA116Qea
Enclosure: Metal enclosure with high-impact
plastic faceplate
Power: 12V DC, 1A power adapter, center-pin-positive
polarity
Daisy-Chain: Maximum of 16 OmniView KVM Switches
No. of Servers Supported: 4, 8, and 16 respectively for 4-, 8-, and 16-port
models (256 servers max. via daisy-chaining)
Monitors Supported: CRT and LCD (with VGA support)
Max. Resolution: Up to 1920x1440 @ 75Hz
Keyboard Input: PS/2 (miniDIN6)
Mouse Input: PS/2 (miniDIN6)
Monitor Port: VGA (HDDB15 female)
CPU Ports: SCSI-50
Daisy-Chain Ports: DB25 female
Flash-Upgrade Port: RJ11
Direct Port Selectors: 4, 8, and 16 respectively for 4-, 8-, and
16-port models
Operating Temp: 32° to 104° F (0~40° C)
Storage Temp: -4° to 140° F (20~60° C)
Humidity: 0-80% RH, non-condensing
Warranty: 3 years
Dimensions: (F1DA104Qea) 11 x 1.75 x 6 in.
(279mm x 44.5mm x 150mm)
(F1DA108Qea) 17.25 x 1.75 x 7.5 in.
(438mm x 44.5mm x 190mm)
(F1DA116Qea) 17.25 x 3.5 x 7.5 in.
(438mm x 89mm x 190mm)
Weight: (F1DA104Qea) 5.3 lbs. (2.4kg.)
(F1DA108Qea) 9.2 lbs. (4.2kg.)
(F1DA116Qea) 10.1 lbs. (4.5kg.)
Note: Specifications are subject to change without notice.

1110
1110
Pre-Configuration
Where to Place the PRO3 KVM Switch
The enclosure of the PRO3 KVM Switch is designed for stand-alone or
rack-mount configuration. The 8- and 16-Port PRO3 KVM Switches are natively
rack-mountable in standard, 19-inch server racks. Rack-mount hardware is
included with these Switches for a sturdy rack installation. An optional OmniView
Rack-Mount Kit (F1D005) is available for use with the 4-Port PRO3 KVM Switch.
Consider the following when deciding where to place
the PRO3 KVM Switch:
• whether or not you intend to use the direct-access port selectors
• the lengths of the cables attached to your keyboard, monitor, and mouse
• the location of your servers in relation to your console
• the lengths of the cables you use to connect your servers
to the PRO3 KVM Switch
Cable-Distance Requirements:
For PS/2 Servers:
VGA signals transmit best up to 25 feet (7.6m). Beyond that length, the
probability of video degradation increases. For this reason, Belkin recommends
that the length of the cables between the PRO3 KVM Switch and the connected
servers does not exceed 25 feet (7.6m).
Note: The Belkin OmniView CAT5 Extender (F1D084vea2) may be used to
extend your console (keyboard, mouse, and monitor) by up to 300 feet (91m).
Cautions and Warnings!
Avoid placing cables near fluorescent lights, air-conditioning equipment, or
machines that create electrical noise (e.g., vacuum cleaners).
Before attempting to connect anything to the PRO3 KVM Switch or your servers,
ensure that everything is powered off. Plugging and unplugging cables while
servers are powered on may cause irreversible damage of the servers and/or the
PRO3 KVM Switches. Belkin is not responsible for damage caused in this way.
You are now ready to begin installation of your PRO3 KVM Switch.
The following sections (pages 11-16) provide complete instructions
for the hardware setup of a single PRO3 KVM Switch (F1DA104Qea,
F1DA108Qea, F1DA116Qea).
Installation

11
10
1
2
3
4
5
6
7
8
section
11
10
Installation
Mounting the PRO3 KVM Switch
Bracket Installation (F1DA108Qea and F1DA116Qea)
Eight- or 16-Port PRO3 KVM Switches include adjustable mounting brackets
ideal for installation in 19-inch racks. The mounting brackets feature three
adjustment positions to allow you to set the PRO3 KVM Switch’s face flush with
the ends of the rails or to extend the PRO3 KVM Switch past the front of the rails.
Please follow these simple steps to achieve the desired adjustment.
Step 1
Determine how far you would like the PRO3 KVM Switch to protrude from the
rack. Select a bracket-hole scheme.
Step 2
Attach the bracket to the side of your PRO3 KVM Switch using the Phillips
screws provided. (Refer to diagram below.)
Step 3
Mount the PRO3 KVM Switch to the rack-rail assembly. (Refer to diagram below.)
Note: If this PRO3 KVM Switch will be daisy-chained to another KVM switch, set
the BANK address prior to installing on a rack. Refer to the section in this User
Manual titled “Connecting Multiple PRO3 KVM Switches (Daisy-Chaining)”.
Your PRO3 KVM Switch is now mounted securely into the bracket and you are
ready to connect the console.

13
12
13
12
Installation
Optional Bracket Installation (F1DA104Qea)
The PRO3 4-Port KVM Switch can be installed into a 19-inch server rack using
an optional OmniView Rack-Mount Kit (F1D005).
Step 1
Attach the rack-mount bracket to your 4-Port PRO3 KVM Switch using the
Phillips screws provided. (Refer to diagram below.)

13
12
1
2
3
4
5
6
7
8
section
13
12
Installation
Step 2
Mount the 4-Port PRO3 KVM Switch to the rack-rail assembly. (Refer to
diagram below.)
Note: If this PRO3 KVM Switch will be daisy-chained to another KVM switch,
set the BANK address prior to installing on a rack. Refer to the section titled
“Connecting Multiple PRO3 KVM Switches (Daisy-Chaining)” in this User Manual.
Your PRO3 KVM Switch is now mounted securely to the rack and you are ready
to connect the console.
Note for Belkin PRO2 Series Owners (F1DA104Tea, F1DA108Tea, and
F1DA116Tea): Installation for the PRO2 KVM Switch has changed.
Please follow this installation manual completely to ensure proper
installation. Failure to do so may result in keyboard or mouse errors,
and/or faulty operation.

15
14
Installation
Connecting the Console to the PRO3 KVM Switch
Step 1
Connect the VGA monitor cable to the HDDB15 female port on the back of the
PRO3 KVM Switch in the “Console” section. (Refer to diagram below.)
Step 2
Connect the PS/2 keyboard cable to the keyboard port on the back of the PRO3
KVM Switch in the “Console” section. (Refer to diagram below.)
Step 3
Connect the PS/2 mouse cable to the mouse port on the back of the PRO3 KVM
Switch in the “Console” section. (Refer to diagram below.)
Step 4
Attach the power adapter to the DC power jack labeled “12VDC, 1A” located on
the rear panel of the PRO3 KVM Switch. Only use the power adapter supplied
with the unit. (Refer to diagram below.)

1
2
3
4
5
6
7
8
section
1514
Installation
Your PRO3 KVM Switch is now installed and you are ready to connect
your servers.
Connecting PS/2 Servers to the PRO3 KVM Switch
Step 1
Make sure your server is powered off.
Step 2
Using the Belkin Dual-Port Micro-Cable Kit for PS/2 (F1D9400-XX), connect the
VGA connector to the monitor port on your server. (Refer to diagram below.)
Step 3
Connect the PS/2 mouse and keyboard connectors to the mouse and keyboard
ports on the server. (Refer to diagram below.)

1716
1716
Installation
Step 4
Connect the Belkin Dual-Port Micro-Cable Kit for PS/2 to the desired host ports
on the PRO3 KVM Switch. (Refer to diagram below.)
Step 5
Power up your server.
Step 6
Repeat Steps 1 through 5 for each additional PS/2 server you wish to connect.
Note: This KVM Switch does NOT support USB connection to servers.

1716
1
2
3
4
5
6
7
8
section
1716
Installation
Connecting Multiple PRO3 KVM Switches
(Daisy-Chaining)
You can daisy-chain up to 16 PRO3 KVM Switches, allowing a server
administrator to manage up to a maximum of 256 servers from one console.
Each daisy-chained PRO3 KVM Switch is referred to as a “BANK” and is
assigned an address. The PRO3 KVM Switch connected to the console
keyboard, mouse, and monitor is BANK 00 and is referred to as the “primary”
KVM switch. BANKs 01 through 15 are referred to as “secondary” KVM switches.
Note: Your PRO3 KVM Switch is backward-compatible with Belkin OmniView
PRO2 KVM Switches with standard cabling (F1DA104Tea, F1DA108Tea,
F1DA116Tea). In a daisy-chain configuration, the PRO3 KVM Switch with micro-
cabling (F1DA104Qea, F1DA108Qea, F1DA116Qea) must be designated as the
primary KVM switch. (Refer to the diagram below.)
cable 1
cable 2
cable 3
Primary unit (BANK 00)
Secondary unit ( BANK 01)
Secondary unit ( BANK 02)
Secondary unit ( BANK 03)
Note: A Daisy-Chain Cable (F1D108-CBL) is required to daisy-chain each
PRO3 KVM Switch and is available through your Belkin reseller,
or online at www.belkin.com.

1918
1918
Installation
How to Assign a BANK Address
All PRO3 KVM Switches feature a “BANK DIP” switch. The “BANK DIP” switch is
used to assign the proper BANK address to each PRO3 KVM Switch.
• For a single-unit configuration, set the “BANK DIP” switch on the PRO3 KVM
Switch to the “primary” (BANK address 00) setting. This is the factory
default setting.
• For a multi-unit configuration, the “BANK DIP” switch on the primary KVM
switch must be set to “BANK address 00”. Each secondary unit must be set
to a unique BANK address (from 01 through 15). Refer to the chart below for
“BANK DIP” switch settings.
BANK-DIP-Switch Configuration Chart
DIP SWITCH# BANK
ADDRESS
1 2 3 4 5 6
ON ON ON ON ON ON BANK 0 PRIMARY (default)
ON ON OFF ON ON ON BANK 1 SECONDARY
ON ON ON OFF ON ON BANK 2 SECONDARY
ON ON OFF OFF ON ON BANK 3 SECONDARY
ON ON ON ON OFF ON BANK 4 SECONDARY
ON ON OFF ON OFF ON BANK 5 SECONDARY
ON ON ON OFF OFF ON BANK 6 SECONDARY
ON ON OFF OFF OFF ON BANK 7 SECONDARY
ON ON ON ON ON OFF BANK 8 SECONDARY
ON ON OFF ON ON OFF BANK 9 SECONDARY
ON ON ON OFF ON OFF BANK 10 SECONDARY
ON ON OFF OFF ON OFF BANK 11 SECONDARY
ON ON ON ON OFF OFF BANK 12 SECONDARY
ON ON OFF ON OFF OFF BANK 13 SECONDARY
ON ON ON OFF OFF OFF BANK 14 SECONDARY
ON ON OFF OFF OFF OFF BANK 15 SECONDARY
ON = Up Position, OFF = Down Position
Example: Four 8-Port PRO3 KVM Switches (F1DA108Zea) are daisy-chained
together to manage up to 32 servers. The DIP switch on the primary KVM switch
is set to “BANK 00” (factory default) and the secondary units are each set to a
unique BANK (between 01 and 03).