Belkin OmniView F1DN102DEA User manual

User Manual
F1DN102Dea
F1DN104Dea
OmniView®Secure DVI
Dual-Link KVM Switch

Table of Contents
1. Introduction.............................................................................................1
Package Contents ........................................................................... 1
2. Overview .................................................................................................2
Security Features ............................................................................ 2
Other Features ................................................................................ 3
Equipment Requirements ................................................................. 4
System Requirements ...................................................................... 5
Unit Display Diagrams ..................................................................... 6
Specifications.................................................................................. 7
3. Installation..............................................................................................8
Pre-Configuration ............................................................................ 8
Mounting the Switch (optional)......................................................... 9
Connecting the Console to the Switch ............................................10
Connecting Computers to the Switch ..............................................11
Powering Up the Systems...............................................................12
4. Using your Switch..................................................................................13
Selecting a Computer Using Port Selectors.....................................13
5. Frequently Asked Questions ..................................................................14
6. Troubleshooting ....................................................................................16
7. Information ...........................................................................................18

1
1
2
3
4
5
6
7
section
Congratulations and thank you for purchasing this Belkin OmniView Secure
DVI Dual-Link KVM Switch (the Switch). Designed especially for secure military
and government installations, the Switch provides the centralized control
required by today’s IA (Information Assurance) computer environments. It
allows users to manage multiple computers from a single USB console, while
preventing unintended data transfer between computers running on different
security levels.
This User Manual provides all the details you’ll need to install and operate
your new Switch, in addition to expert troubleshooting advice—in the unlikely
event of a problem. For quick and easy installation, please refer to the Quick
Installation Guide included in your packaging.
Important: Tamper-evident seals have been placed on both sides of the
Switch enclosure, to provide evidence if the product has been opened and
potentially compromised (see diagram on page 6). If either seal has been
removed or appears disrupted, please call Belkin Technical Support at
[phone].
User Manual
OmniView Secure
DVI Dual-Link
KVM Switch
5V DC, 3A Global
Power Adapter
Quick
Installation Guide
Package Contents
4 Interchangeable
AC Plugs1
1Includes AC plugs for the U.S., U.K., Europe, and Australia.
Introduction

2
Security Features
• DedicatedProcessors
Designed specifically for secure environments, the Switch features a
dedicated processor per computer port. This keeps each computer running
on different security levels completely separated and secure at all times, and
prevents any unintended data transfer between computers.
• NoMemoryBuffer
The Switch does not have a memory buffer and does not have the ability
to store data. This prevents any keystrokes or other data input from being
unintentionally transferred as you switch between computers, ensuring the
integrity of your data. The Switch does not include any features that require
memory, such as hot keys, AutoScan, or an on-screen display (OSD).
• Non-ReprogrammableFirmware
The Switch features custom firmware that is not reprogrammable, preventing
the ability to tamper with the KVM logic.
• Tamper-EvidentSeals
Tamper-evident seals are placed on both sides of the enclosure, to provide
indication if the Switch has been opened or compromised.
• Tamper-ProofHardware
All integrated circuits are soldered directly to the printed circuit board to
prevent tampering with the components.
• NIAPListing
The Switch is listed by the National Information Assurance Partnership (NIAP).
It is NIAP Common Criteria validated to EAL 4 (Evaluation Assurance Level 4)
augmented with ALC FLR 3.
Overview

3
1
2
3
4
5
6
7
section
3
Overview
Other Features
• USBSupport
The Switch is compatible with USB 1.1 and USB 2.0 technology and supports
Plug-and-Play connectivity with USB computers, keyboards, and mice.
• Dual-LinkDVISupport
The Switch supports video resolutions of up to 2560x1600. This includes
support for digital displays 20 inches and larger.
• AudioSwitching
Allows you to share speakers and microphone between computers.
• DedicatedPortSelectors
Port selectors, located conveniently on the front panel of the Switch, allow you
to switch easily from one computer to the next. Each button controls a single
computer port.
• LEDIndicators
An LED above each port selector illuminates to indicate that the console
currently controls the corresponding computer. As a port selector is pushed,
the LED above it will illuminate.
• MetalEnclosure
The Switch features a rugged, metal enclosure that provides stability and
allows the Switch to be placed beneath your monitor or other desk item.
• DesktoporRack-MountInstallation
With its compact design, the Switch can be placed on your desktop or
mounted to a standard 19-inch server rack for 1U installation.2
• GlobalPowerAdapter
The Switch includes a global power adapter and interchangeable plugs, to
allow for both domestic and international installations.3
2The 2- and 4-Port Switches require an optional Rack-Mount Kit for rack installation
(Belkin part number F1D005).
3Includes AC plugs for the U.S., U.K., Europe, and Australia.

4
Overview
EquipmentRequirements
Cables
Belkin highly recommends you use
Belkin DVI/USB KVM Cable Kits with
Audio & Mic for your Switch to help
ensure superior performance. These
cables offer the highest quality possible
to ensure optimal data and audio video
transmission. One Cable Kit is required
per connected computer.
Belkin DVI/USB KVM Cable Kits
with Audio & Mic:
F1D9201-06 – 6 ft. (1.8m)
F1D9201-10 – 10 ft. (3m)
F1D9201-15 – 15 ft. (4.6m)
Note: Due to USB and DVI limitations,
the cable length cannot exceed 15
feet (4.6m).
F1D9201b-XX

5
1
2
3
4
5
6
7
section
Overview
SystemRequirements
Operating-System(OS)Platforms
The Switch is compatible with computers running on, but not limited to, the
following OS platforms:
•Windows®2000
•WindowsXP(Home/Professional)
•Windows2003Server
•WindowsVista®
•RedHat®Linux®Desktop
•RedHatEnterpriseLinuxWS
•MacOS®X v10.3 and higher
Keyboards
•USB-compatible(includingwirelesskeyboards)
Mice
•USB-compatible(includingwirelessoropticalmice)
Monitors
•DigitaldisplayswithDVI-Dsupport,single-linkanddual-link
Speakers
• Computerspeakerswith3.5mmstereoplug
Microphone
• Computermicrophonewith3.5mmplug

66
   
Overview
UnitDisplayDiagrams
Front View
(F1DN104Dea model shown)
BackView
Tamper-Evident Seals
Side View
IMPORTANT NOTICE: There should be one tamper-evident seal on
each side of the Switch enclosure (total of two seals). If both seals
are visible and do not appear to be disrupted, your Switch has not
been opened or compromised since time of production. If for any
reason one of the seals is missing or appears disrupted, please call
Belkin Technical Support at [phone].
Console USB
Keyboard Port
LED Indicators
Port Selectors
Console Audio/Mic
Input Jacks
Computer DVI, USB, and
Audio/Mic Ports
DC Power Jack
Console DVI
Monitor Port
Console USB
Mouse Port

7
1
2
3
4
5
6
7
section
Overview
Specifications
PartNo.: F1DN102Dea, F1DN104Dea
Enclosure: Metal enclosure with high-impact plastic faceplate
PowerRequirements: 5V DC, 3A (minimum) power adapter with
center-pin-positive polarity4
ACInput: 100 to 240VAC
InterchangeableACPlugs: 4 (U.S., U.K., Europe, Australia)
No.ofUsersSupported: 1
No.ofComputersSupported: 2 and 4 respectively for 2- and 4-port models
MonitorsSupported: Single-Link and Dual-Link digital DVI-D displays
ResolutionSupport: Up to 2560x1600
ConsoleKeyboardInput: USB Type A
ConsoleMouseInput: USB Type A
ConsoleMonitorPort: DVI Dual-Link female
ConsoleSpeaker/Mic: 3.5mm female
CPUKeyboard/MousePorts: USB Type B
CPUAudio/Mic: 3.5mm female
CPUMonitorPorts: DVI Dual-Link female
PortSelectors: 2 and 4 respectively for 2- and 4-port models
LEDIndicators: 2 and 4 respectively for 2- and 4-port models
OperatingTemp: 32° to 104° F (0° to 40° C)
StorageTemp: -4° to 140° F (-20° to 60° C)
Humidity: 0-80%RH,non-condensing
Warranty: 3 years
Dimensions: (F1DN102Dea) 11 x 1.75 x 6 in. (279 x 45 x 150mm)
(F1DN104Dea) 11 x 1.75 x 6 in. (279 x 45 x 150mm)
Weight: (F1DN102Dea) 2.5 lbs. (1.1kg.)
(F1DN104Dea) 2.5 lbs. (1.1kg.)
Made in the USA of imported parts
4The Switch includes a 5-volt, 3-Amp power adapter.

8
Before you begin, please take a few minutes to register your product.
This may assist Belkin in contacting you regarding important information
regarding secure use of your product. You may register your product online
by going to https://www.belkin.com/registration/.
Pre-Configuration
WheretoplacetheSwitch:
The enclosure of the Switch is designed for desktop or rack-mount configuration.
An optional Rack-Mount Kit (Belkin part number F1D005) is available for use with
the 2- and 4-Port Switches.
ConsiderthefollowingwhendecidingwheretoplacetheSwitch:
•yourproximitytotheportselectorsonthefrontoftheSwitch
•thelengthsofthecablesattachedtoyourkeyboard,monitor,andmouse
•thelocationofyourcomputersinrelationtoyourconsole
•thelengthsofthecablesyouusetoconnectyourcomputerstotheSwitch
Warning: Avoid placing cables near fluorescent lights, air-conditioning
equipment, or machines that create electrical noise (e.g., vacuum cleaners).
Installation

9
1
2
3
4
5
6
7
section
Installation
Step1MountingtheSwitch(optional)
BracketInstallation(F1DN102DeaandF1DN104Dea)
The 2- and 4-Port Switches can be installed into a 19-inch rack using an optional
Rack-Mount Kit, sold separately (Belkin part number F1D005).
1.1 Attach the Rack-Mount Bracket to the Switch using the Phillips screws
provided. (Refer to diagram below.)
1.2 Mount the Switch to the rack rails. (Refer to diagram below.)
Your Switch is now mounted securely to the rack and you are ready to
connect your console.

101010
Installation
Step2 ConnectingtheConsoletotheSwitch(required)
Warning: Before attempting to connect anything to the Switch or your
computers, please ensure that all computer equipment and devices are powered
off. Plugging and unplugging cables while computers are powered on may cause
irreversible damage to the computers and/or the Switch. Belkin International,
Inc., is not responsible for damage caused by your failure to do so.
Before you connect your console to the Switch, make sure that your USB
keyboardandmouseworkproperlywithallyourcomputers(theHumanInterface
Device(HID)USBdriversareinstalledonallcomputers).
2.1 Connect your monitor DVI cable to the DVI port on the back of the Switch
in the “User Console” section. (Refer to diagram below.)
2.2 Connect your keyboard and mouse USB cables to the USB keyboard and
mouse ports on the back of the Switch in the “User Console” section.
(Refer to diagram below.)
2.3 Connect your speaker and microphone cables into the corresponding
ports in the “User Console” section.

11
1
2
3
4
5
6
7
section
Installation
Step3 ConnectingComputerstotheSwitch(required)
3.1 Make sure all computers and the Switch are powered off.
3.2 Using the Belkin DVI/USB KVM Cable Kit (F1D9201b-XX), connect the
male DVI connector to the monitor port on your computer. Then connect
the other end of the cable into an available port on the Switch. (Refer to
diagram below.)
3.3 Using the Cable Kit, connect the USB Type A connector to an available
USB port on your computer. Then connect the USB Type B connector to
the corresponding USB port on the Switch. (Refer to diagram below.)
3.4 Connect the two audio cables (audio and microphone) to your computer.
Then connect the other end to the corresponding audio and microphone
port on the Switch.
3.5 Repeat the steps above for each additional USB computer you wish
to connect.
Note: The Cable Kit must be connected directly to a free USB port on your
computer, with no USB hubs or other devices in between.

12
Installation
Step4 PoweringUptheSystems(required)
4.1 Power on the attached monitor.
4.2 Attach the power adapter to the DC power jack labeled “5V, 3A” on the
back of the Switch. Only use the power adapter supplied with the Switch.
(Refer to diagram below.)
4.3 Power on your computers. All computers can be powered
on simultaneously.
Note:Your computers should recognize the Switch and automatically install the
HIDUSBdriverifnecessary.
When you power on your computers, the Switch emulates both a
mouse and keyboard on each port and allows your computers to
boot normally. The computer connected to port “1” will be displayed
on the monitor. Check to see that the keyboard, monitor, and mouse
are working normally. Proceed to do this with all occupied ports to
verify that all computers are connected and responding correctly.
If you encounter an error, check your cable connections for that
computer and reboot. If the problem persists, please refer to the
Troubleshooting section in this User Manual.

13
section
1
2
3
4
5
6
7
Using your Switch
SelectingaComputerUsingPortSelectors
Now that you have connected your console and computers to the Switch,
it is ready for use. You can select which computer you wish to control by
pressing the corresponding port selector on the front of the Switch. The LED
will illuminate to indicate which computer (or port) is currently selected. It
takes approximately 1–2 seconds for the video signal to refresh after switching
computers. Re-synchronization of the mouse and keyboard signals also
occurs. This is normal operation and ensures that proper synchronization is
established between the console and the connected computers.5
Once you press a port selector, the Switch immediately disables the connection
between your console and the previously selected computer, and establishes
a new connection between your console and the new computer selected.
Keyboard and mouse inputs can only be sent to the selected computer, and
video outputs can only be received from the selected computer. The Switch also
prevents
any data transfer between connected computers, ensuring the security of
your computers.
Please note that the default port at power-up is port one. In case of
a power failure or if the power is cycled, the Switch will default to
port one.
5Note: It may take longer for your mouse and keyboard to re-synchronize
whenthecomputerisrecovering(orinitializing)fromStandby,Hibernate,or
Sleep modes.

14
Frequently Asked Questions
WhatdoesNIAPCommonCriteriavalidationtoEAL4mean?
To learn more about NIAP Common Criteria and EAL 4, visit
http://www.niap-ccevs.org/cc-scheme/consumer-guidance.cfm.
WhatdoIdoifIfindthatthetamper-evidentsealsontheSwitchhave
beenremovedordisrupted?
Please call Belkin Secure KVM Support at [phone] immediately.
The KVM Switch’s circuitry may have been compromised.
WherecanIregistermySwitch?
You can register your Switch on the Web by directing your browser to:
https://www.belkin.com/registration.
WherecanIgotoreportaproductissue?
You may call Belkin Secure KVM Support at [phone] or direct your web
browser to http://www.belkin.com/support/contact/email/technicalsupport/.
HowdoestheSwitchallowtheusertoswitchbetweencomputers?
The Switch only supports one method of port selection. The user can access
the desired computer by pushing the associated port selector.
HowfarcantheSwitchbefrommycomputer?
The Switch can be located up to 15 feet (4.6m) away from your computer due
to DVI- and USB-cable limitations.
DoIhavetoinstallsoftwaretousetheSwitch?
No, the Switch does not require any software to be installed on your computers.
CanIusetheSwitchwithacomputerthatdoesnotsupportUSB?
No, the Switch only works with USB-capable computers.
DoestheSwitchrequireanACadapter?
Yes, the Switch requires a 5-volt DC, 3-Amp (minimum) power adapter in order
to function properly.

15
1
2
3
4
5
6
7
section
Frequently Asked Questions
DoestheSwitchsupportLinux?
Yes,theSwitchworkswithRedHatLinuxandsomeLinuxoperatingsystems
configured for USB support.
DoestheSwitchsupportMicrosoft®IntelliMouse®?
The Switch supports mice from Belkin, Microsoft, Logitech®, Kensington®, and
many other manufacturers. Please contact Belkin Technical Support at (800)
282-2355 for any compatibility issues you may experience.
General
My computer does not boot when connected to the Switch but
works fine when I connect my keyboard, video, and mouse directly
to my computer.
•MakesurethattheDVI/USBKVMCableKitisconnectedfirmly
between the Switch and the computer.
Video
I am getting ghosting, shadowing, or fuzzy images on my monitor.
•CheckthatallvideocablesareinsertedproperlytotheSwitch,
computer, and monitor.
•Checkthatthemonitoryouareusingsupportstheresolutionand
refresh-rate setting on your computer.
•Lowerthevideoresolutionofyourmonitor.
•Checkthatthevideo-cablelengthdoesnotexceed15feet(4.6m).
•Checkthatthegraphicscardyouareusingsupportstheresolution
and refresh-rate setting on your computer.
•Connectthemonitordirectlyintothecomputeryouarehaving
trouble with to see if the problem still appears.
I am getting a black screen on my monitor.
•Checkthatallvideocablesareinsertedproperly.
•Checkthatthereispropervoltageavailabletothepoweradapter
and that it is inserted correctly.
•Connectyourmonitordirectlytothecomputertoverifythatyour
monitor is functioning properly.
•Rebootthecomputer.

16
Keyboard
The computer does not detect my keyboard, or my keyboard does
not work when I switch computers or reboot.
•Checkthatthekeyboardyouareusingisconnectedproperlyto
the Switch.
•CheckthattheUSBcablebetweentheSwitchandthecomputeris
firmly connected.
•TryconnectingtoadifferentUSBportonthecomputer.
•Makesurethekeyboardworkswhendirectlypluggedintothe
computer(theHIDUSBdriverisinstalledonthecomputer).
Rebooting may be necessary when trying this.
•Ifyouareusingkeyboardsoftwarethatwasincludedwithyour
keyboard, uninstall it and then reinstall.
•Ifthecomputeriscomingoutofstandbymode,allowuptoone
minute to regain keyboard function.
•Tryadifferentkeyboard.
Some of the keys on my keyboard are not functioning properly
when I use a Mac®computer.
•IfyouareusingaPCkeyboardonaMacsystem,afewoftheoption
keys on your PC keyboard may be reversed. All major keys will
function as labeled.
Troubleshooting

17
1
2
3
4
5
6
7
section
Troubleshooting
Mouse
The computer does not detect my mouse, or my mouse does not
work when I switch computers or reboot.
•Checkthatthemouseyouareusingisconnectedproperlyto
the Switch.
•CheckthattheUSBcablebetweentheSwitchandthecomputeris
completely connected.
•TryconnectingtoadifferentUSBportonthecomputer.
•Makesurethemouseworkswhendirectlypluggedintothecomputer
(theHIDUSBdriverisinstalledonthecomputer).Rebootingmaybe
necessary when trying this.
•Ifyouareusingamousedriverthatwasincludedwithyourmouse,
uninstall it and install the standard Microsoft mouse driver.
•Ifthecomputeriscomingoutofstandbymode,allowuptoone
minute to regain mouse function.
•Tryadifferentmouse.

Information
18
FCC Statement
DeclarationofConformitywithFCCRules
forElectromagneticCompatibility
We, Belkin International, Inc., of 501 West Walnut Street, Compton, CA 90220, declare
under our sole responsibility that the products:
F1DN102Dea, F1DN104Dea,
to which this declaration relates:
Comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CEDeclarationofConformity
We, Belkin International, Inc., declare under our sole responsibility that the products
F1DN102Dea, F1DN104Dea, to which this declaration relates, are in conformity with
Emissions Standard EN55022 and with Immunity Standard EN55024, LVP EN61000-3-2,
and EN61000-3-3.
ICES
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique
de la classe B est conforme á la norme NMB-003 du Canada.
BelkinInternational,Inc.,Limited3-YearProductWarranty
What this warranty covers.
Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this Belkin product
that the product shall be free of defects in design, assembly, material, or workmanship.
Whattheperiodofcoverageis.
Belkin warrants the Belkin product for three years.
Whatwillwedotocorrectproblems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of charge (except
for shipping charges for the product). Belkin reserves the right to discontinue any of its
products without notice, and disclaims any limited warranty to repair or replace any such
discontinued products. In the event that Belkin is unable to repair or replace the product
(for example, because it has been discontinued), Belkin will offer either a refund or a
credit toward the purchase of another product from Belkin.com in an amount equal to the
purchase price of the product as evidenced on the original purchase receipt as discounted
by its natural use.
Whatisnotcoveredbythiswarranty?
All above warranties are null and void if the Belkin product is not provided to Belkin
for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin
determines that the Belkin product has been improperly installed, altered in any way, or
tampered with. The Belkin Product Warranty does not protect against acts of God such
as flood, lightning, earthquake, war, vandalism, theft, normal-use wear and tear, erosion,
depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e., brownouts
or sags), non-authorized program, or system-equipment modification or alteration.