Belkin OmniView SOHO KVM User manual

This section provides complete instructions for the hardware setup of a single KVM Switch.
(F1DS102L or F1DS104L)
Installing the KVM Switch
The KVM Switch is a plug-and-play device for installation. For a quick start on installation and
operation, please follow the instructions below for the setup sequence:
Connect the Audio
Once all cables have been connected, power up the KVM Switch followed by the CPUs that are
attached to the KVM Switch. All computers can be powered on simultaneously. The KVM Switch
emulates a mouse and keyboard on each port and allows your computer to boot normally. Your
KVM Switch should now be ready for use.
NOTE: Speakers and microphones are not required for use of your KVM Switch.
Single-Switch Installation Audio and Microphone Connections Powering Up the Systems
Step 1.
Connect the shared keyboard, monitor, and
mouse (also speaker set and microphone) to the
console port of the KVM Switch.
NOTE: Since the USB interface is hot-pluggable, you don’t have to turn off the computer before making connections
to the KVM Switch.
Step 3.
Power up your KVM Switch by connecting the external power adapter to it.
Step 4.
Power up the connected computers one by one. After your computers are powered up, the
keyboard and mouse will be recognized and now you can begin operating the KVM Switch.
Step 2.
Connect each of your computers to the
KVM Switch, using the USB KVM cable, and
audio and mic cables.
Step 1.
Using the audio cable attached to
your speakers, connect the male
3.5mm plug to the lime audio jack in
the “Console” section of the
KVM Switch.
Step 2.
Using the mic cable attached to
your microphone, connect the male
3.5mm plug to the pink mic jack in the
“Console” section of the KVM Switch.
Step 3.
Using the SOHO USB Cable Kit, connect one
end of the lime male 3.5mm plug to the speaker
jack of your sound card or computer, and
connect the other end to the audio jack of the
KVM Switch.
Step 4.
Using the KVM Cable, connect one end of the
pink male 3.5mm plug to the mic jack of your
sound card or computer, and connect the other
end to the pink mic jack of the KVM Switch.

Front View
Back View
KVM Soho VGA U-type 4 Port Enclosure
Print Graphics v.2.1 F1DS102L, F1DS104L
front panel
back panel
KVM Soho DVI 4 Port Enclosure
Print Graphics v.2.1 F1DD102L, F1DD104L
front panel
back panel
KVM Soho VGA T-type 4 Port Enclosure
Print Graphics v.2.1 F1DS102J, F1DS104J
front panel
back panel
Audio/Mic Switch
KVM Switch
USB Hub
Port 1
Port Indicators
KVM Soho VGA U-type 4 Port Enclosure
Print Graphics v.2.1 F1DS102L, F1DS104L
front panel
back panel
KVM Soho DVI 4 Port Enclosure
Print Graphics v.2.1 F1DD102L, F1DD104L
front panel
back panel
KVM Soho VGA T-type 4 Port Enclosure
Print Graphics v.2.1 F1DS102J, F1DS104J
front panel
back panel
DC Power Jack
Additional Computer Audio/Mic Jacks
1st Computer
Audio/Mic
Console Jacks Audio/Mic
Console
Jacks
USB Hub
Port 2
VGA Console
Port
1st Computer
Port
2nd Computer
Port
3rd Computer
Port
4th Computer
Port
USB Console
Port
Belkin Tech Support
US: 800-223-5546 ext. 2263
310-898-1100 ext. 2263
UK: 0845 607 77 87
Australia: 1800 235 546
New Zealand: 0800 235 546
Singapore: 65 64857620
Europe: www.belkin.com/support
Belkin International, Inc.
501 West Walnut Street
Los Angeles, CA 90220, USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
[phone]
[phone] fax
Belkin Ltd.
4 Pioneer Avenue
Tuggerah Business Park
Tuggerah, NSW 2259, Australia
[phone]
[phone] fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
[phone]
[phone] fax
© 2008 Belkin International, Inc. All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
Quick Installation Guide F1DS102L
F1DS104L
PM00510
OmniView®SOHO KVM
Switch with Audio
VGA with USB Console and Host Support
OmniView®SOHO KVM
Switch with Audio
VGA with USB Console and Host Support
Start Here