BellAire 7000 User manual

37000BellAire™ Model 7000 Tire Inflator Instructions
Tire Inflator
BellAire7000
12V12V
PURE•PSI
Car Tires, Sports Balls, Airbeds, Boats & Towables
ATTENTION! READ ALL INSTRUCTIONS AND
WARNINGS CAREFULLY BEFORE USE
INSTRUCTIONS FOR USE
INFLATES ALMOST ANYTHING

2
BellAire™ Model 7000 Tire Inflator Instructions
Introduction_______________________________________________________________________________________________2
Featured Product Illustrations______________________________________________________________________________3
General Safety Rules and Warnings_________________________________________________________________________4
Inflator Operation_________________________________________________________________________________________5
Battery Level Indicator Lights____________________________________________________________________________5
Rechargeable Battery Instructions_______________________________________________________________________5
Inflating Tires using 12 Volt power________________________________________________________________________5
Inflating Tires using the internal rechargeable battery________________________________________________________6
Wall Mounting Instructions and Template_________________________________________________________________7-10
Inflator Operation (continued)______________________________________________________________________________11
Inflating sports balls or other high pressure small inflatables using 12 Volt power____________________________11
Inflating sports balls or other high pressure small inflatables using the internal rechargeable battery____________11
Using the high volume/low pressure Raft Inflator_________________________________________________________12
Inflating air mattresses, rafts and floats with the Raft Inflator using 12 Volt power____________________________12
Inflating air mattresses, rafts and floats with the Raft Inflator using the internal rechargeable battery____________13
Deflating air mattresses, rafts and floats with the Raft Inflator using 12 Volt power___________________________13
Deflating air mattresses, rafts and floats with the Raft Inflator using the internal rechargeable battery___________13
Work Light___________________________________________________________________________________________14
Maintenance_____________________________________________________________________________________________14
Trouble Shooting_________________________________________________________________________________________14
Warranty________________________________________________________________________________________________15
Contact Us________________________________________________________________________________________________16
Your new inflator provides up to 150 PSI and may be operated while connected to a 15 amp 12 Volt DC power outlet or
in portable mode using its internal rechargeable battery. The BellAire™ 7000 includes a high pressure inflator for vehicle
tires and sports balls and a high volume low pressure raft inflator for inflating and deflating air mattresses, rafts and floats.
This model also includes an inflation pre-set and automatic shut-off feature, a 12 Volt DC power outlet for powering 12
Volt tools and small appliances not exceeding 15 amps and a (6) LED work light.
This portable inflator has been designed with wall mount features for storage and for internal battery charging.
INSPECT INFLATOR AFTER UNPACKING
After unpacking your inflator, carefully inspect the inflator to ensure there is no damage that may have occurred during
transit and verify all components have been included as listed and shown on page 3.
IMPORTANT! READ ALL INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO USE THIS INFLATOR. FAILURE TO
FOLLOW WARNINGS AND COMPLY WITH ALL INSTRUCTIONS COULD RESULT IN FIRE, PROPERTY DAMAGE OR
INJURY TO PERSONS.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
OPERATE INFLATOR WITH 15 AMP 12 VOLT DC CIGARETTE LIGHTER SOCKETS OR 12 VOLT POWER OUTLETS
ONLY. DO NOT USE WITH OLDER 8 AMP CIGARETTE LIGHTER RECEPTACLES.
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
TABLE OF CONTENTS
INTRODUCTION

3
37000
1. Main Power On/Off Switch
To avoid full battery drain and potential damage to
internal battery, turn main power switch off when not
in use
2. Inflator Power Switch - Hi/Off/Lo
Hi = High pressure tire inflator
Lo = Low pressure raft inflator
3. Work Light Power Switch
4. Digital Pressure Gauge with programmable auto
shut-off
5. Pressure Format (PSI, BAR, or KPA) and Reset Button
6. Pressure Check/+ & – Adjust Buttons
7. 14 Foot Coiled Air Hose
8. Air Nozzle Bleeder Valve
9. Coiled Air Hose Support
10. Detachable Air Hose Coupling
11. 12 Volt DC Input Jack for recharging inflator
internal battery
12. Inflator Internal Battery Level Indicator
13. Six LED Rotating Work Light
14. 12 Volt DC Auxiliary Power Socket - 15 amps Max
15. Blade Type Fuse - 15 amps
16. Raft Inflator/Deflator Ports
17. Air Intake/Exhaust Vents
18. 110 VAC Wall Adapter for charging inflator internal
battery
19. Storage Compartment Door
20. Storage Door Release Latch
21. 12 Volt Power Cord Exit Slot
22. 10 Foot 12 Volt Power Cord with replaceable fuse
23. Rubber Feet for noise and vibration suppression
24. Raft Hose and Adapters
25. Inflator Needle Kit
26. Wall Mount Screw Key Slots
27. Wall Mounting Template (Pages 8-9)
28. Carry/Storage Bag (Not shown)
123
4
26
23
19
BellAire
7000
1
14
16
9
2
8
6
5
4
3
7
18
15
1325 121124
22
19
20
21
17 10 4
6 6
5
BellAire7000
PSI
BAR
KPA
0.0
PRODUCT ILLUSTRATIONS
FIGURE 1 — BellAire™7000 Tire Inflator FIGURE 2 — Digital Pressure Gauge
FIGURE 3 — High Pressure Inflator Needle Kit
FIGURE 4 — Low Pressure Raft Hose Adapters
FIGURE 5 — Wall Mounting
Toy Inflator
Adapter
Presta Valve
Adapter
Sports Ball
Adapter

4
BellAire™ Model 7000 Tire Inflator Instructions
• Keep children and others away while operating inflator.
• Keep the inflator dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use
typical vehicle fluids such as brake fluid, gasoline, any petroleum products or strong solvents to clean inflator.
• Operate inflator in an open area and away from any objects that could restrict the flow of air to ventilation
openings.
• Do not operate inflator near fire, flammable liquids or in gaseous or explosive atmospheres.
• Always wear eye protection.
• Always use in a safe area away from traffic and other dangers.
• Do not attempt to disassemble inflator. No user serviceable parts inside. Only user serviceable part is fuse
replacement. See maintenance section on page 14.
• Before each use, always check inflator hoses and 12 Volt cord for weak or worn condition and make certain
all connections are secure. Do not use if a defect is present.
• Do not pull or carry the inflator by the power cord or air hose.
• Do not over stretch power cord or air hose.
• Never point an inflator air hose toward yourself, others or animals.
• Never start a vehicle with the inflator plugged into the DC 12 Volt power socket. See operation instructions
on pages 5 through 13.
• Use the inflator for its intended use only. Do not alter or modify the inflator.
• Do not insert metal objects into the DC 12 Volt power outlet. Doing so may blow the inflator fuse.
• Do not store inflator in a damp or wet location. Protect the inflator from rain, snow or other moisture
sources.
• When not in use, make certain the main power switch is in the off position. See #1 in figure 1, page 3. Store
inflator out of the reach of children.
• IMPORTANCE OF PROPER TIRE PRESSURE
— Correct tire pressure is vital to road safety.
— Correct tire pressure can help improve vehicle fuel economy.
— Regularly check tires on vehicles to meet manufacturer’s recommended tire pressure.
— Always check pressures at ambient temperature, never check immediately following a long trip.
• RECHARGEABLE BATTERY CAUTIONS
The inflator’s internal rechargeable battery must be charged before the initial use and at least once every 6
months. If the power is completely drained from the battery and not recharged within a month, the battery
may not be rechargeable. Turn main power switch to the off position before storing inflator for any length of
time. See #1 in figure 1.
— Do not continue to operate the inflator when the red battery indicator light is on by itself.
— Only use the AC adapter, included with this inflator, for recharging the internal battery.
— Plugging into a cigarette light socket or power socket does not recharge the internal battery. Only the AC
adapter, included with this inflator, will recharge the battery.
— Do not charge the battery at temperatures below 40 °F (5 °C) or above 105 °F (40 °C).
— Do not operate the inflator with the AC recharging adapter connected to the inflator to avoid damage to the
charging adapter, internal battery or inflator. Improper connection of the AC recharging adapter while
operating the inflator may void the warranty.
— Never operate the inflator near fire, flammable gas or liquid.
• WARNING: COMPRESSED AIR CAN BE DANGEROUS
— Never allow children to use this inflator.
— Never leave inflator unattended while running.
— Never over-inflate items. Over-inflation could cause property damage or personal injury.
— Check manufacturer’s recommended inflation pressure before starting the inflation process.
• WARNING: VEHICLE EXHAUST WITHOUT PROPER VENTILATION IS EXTREMELY DANGEROUS
— Never start and leave a vehicle running in a confined or enclosed space such as a garage. Start and run
vehicles outdoors.
GENERAL SAFETY RULES and WARNINGS

5
37000
INFLATOR OPERATION
BATTERY INDICATOR LIGHTS
Green, yellow and red battery level lights indicate the inflator’s internal rechargeable battery’s current power condition.
See battery level lighting chart below.
GREEN LIGHT YELLOW LIGHT RED LIGHT BATTERY LEVEL LIGHTS
ON ON ON Full to normal battery power
OFF ON ON Weak battery power – Needs recharging
OFF OFF ON Exhausted battery power – Needs recharging immediately*
* Do not continue to operate the inflator when the red battery indicator light is on by itself.
USING THE AC POWER ADAPTER TO RECHARGE INFLATOR INTERNAL BATTERY
1. Before recharging internal battery, see “Rechargeable Battery Cautions”, page 4.
2. Ensure the main power switch is in the “on” position and the inflator power switch and work light power switch are
in the “off” position. See #1, #2 & #3 in figure 1, page 3.
3. Insert the AC power adapter plug into the “DC In” socket on the front of the inflator. See #11 in figure 1.
4. Plug the 110 AC adapter into a 110 Volt electrical outlet. See #18 in figure 1.
5. The red recharging indicator light should flash indicating the battery is recharging.
6. Before first use, charge inflator battery for 14 to 16 hours. After initial charge and subsequent usage, the battery
requires 7 to 9 hours to recharge. If the unit is used too long after the red battery level light comes on, recharging
time could take up to 20 hours.
7. For best results, charge the battery in temperatures ranging from 65 °F (18 °C) to 75 °F (24 °C). If the inflator has
been exposed to below or above the safe charging temperature range, let inflator adjust in the appropriate climate
for 3 hours before charging.
8. When fully charged, the internal battery should be capable of filling a standard P195/65R15 tire 4 to 5 times.
NOTE: In the event the battery level is low to exhausted, the inflator can still be used if powered by using the 12 Volt DC
power cord attached to a vehicle 12 Volt cigarette lighter socket. The inflator will only draw power from the vehicle 12
Volt cigarette lighter when the 12 Volt cord is plugged in.
For the safety of your vehicle and your new BellAire™ 7000 tire inflator, set your vehicle emergency brake and follow
instructions for use as provided.
INFLATING TIRES
USING A VEHICLE 12 VOLT DC CIGARETTE LIGHTER SOCKET TO INFLATE TIRES:
1. Remove and unwind 12 Volt power cord from the storage compartment. See #22 in figure 1, page 3.
2. Make certain the inflator main and inflator power switches are both in the off position. See #1 & #2 in figure 1.
3. Set emergency brake and start vehicle engine. See “Warning: Vehicle Exhaust Without Proper Ventilation”, page 4.
4. Plug inflator lighter plug into vehicle 12 Volt cigarette lighter socket.
5. Turn on the main power switch only. See #1 in figure 1.
6. Check manufacturer’s recommended tire pressure specifications indicated on the tire sidewall.
7. Choose the desired pressure format (PSI, BAR, or KPA) by pressing the “R” button. Press “R” button until desired pres-
sure format appears on the LCD display. See #5 in figure 2, page 3.
IMPORTANT: The “R” re-set button should never be pressed while the air hose is connected to the tire and the “R”,”+”, “–“
buttons should never be pressed while the tire inflator is running. If the “R” button is accidently pressed, turn the inflator
power switch only to the off position (see #2 in figure 1), then press and hold down “–“ to check the pre-set pressure. See
#6 in figure 2. Adjust “+” or “–“ to set desired pressure.
8. Set the auto shut-off pressure level by pressing the “+” or “–“ buttons. Once the pre-set pressure is set, wait a few
seconds for the display to change back to zero.
9. Extend the air hose from its storage location and attach air hose nozzle to vehicle tire valve stem by threading the
nozzle onto the stem clockwise until secure. See #7 & #9 in figure 1.
NOTE: When the nozzle is connected correctly, wait 5-7 seconds and the gauge will indicate the current tire pressure.

6
BellAire™ Model 7000 Tire Inflator Instructions
Always follow the manufacturer’s inflation pressure recommendations to avoid over-inflation. If the tire is over-inflated,
press the deflation bleeder valve button to release air until pressure gauge indicates the correct pressure. See #8 in
figure 1.
The pressure gauge has a built-in memory and will default to the last tire pressure set in the pressure gauge display of the
inflator.
The pressure gauge on the inflator is for reference only and is therefore not binding for exact values. While inflating, the
gauge is a measurement of the fluctuating pressure between the tire and the high pressure hose. To reduce the risk of
over-inflation, use a reliable pressure gauge periodically during inflation before driving a vehicle inflated with the inflator.
10. Turn on inflator power switch to the HI position. See #2 in figure 1. The BellAire™ 7000 will now inflate your tire to
the pre-set pressure level and then shut off automatically. After pre-set auto shut-off has taken place, turn inflator
power switch to the off (middle) position. See #2 in figure 1.
11. To stop inflator before reaching the pre-set auto shut-off pressure, turn inflator power switch to the off (middle) posi-
tion. See #2 in figure 1.
12. Remove air hose nozzle from vehicle tire valve stem by turning air hose nozzle counterclockwise and return air hose
to its built-in storage location on inflator.
13. Turn off the inflator main power switch.
14. Unplug inflator from vehicle 12 Volt cigarette lighter socket and store cord in its storage compartment.
15. Turn off vehicle.
16. Properly store your tire inflator in the carry bag provided.
USING THE INTERNAL RECHARGEABLE BATTERY TO INFLATE TIRES:
1. Turn on the main power switch only. See #1 in figure 1, page 3.
2. Check the inflator to make certain green battery level indicator is on indicating a good battery power level. If the bat-
tery level indicator is not green, refer to directions under the “Rechargeable Battery Cautions” section on page 4 and
“Battery Indicator Light Chart” section on page 5.
3. Check manufacturer’s recommended tire pressure specifications indicated on the tire sidewall.
4. Choose the desired pressure format (PSI, BAR, or KPA) by pressing the “R” button. Press “R” button until desired pres-
sure format appears on the LCD display. See #5 in figure 2, page 3.
IMPORTANT: The “R” re-set button should never be pressed while the air hose is connected to the tire and the “R”,”+”, “–“
buttons should never be pressed while the tire inflator is running. If the “R” button is accidently pressed, turn the inflator
power switch only to the off position (see #2 in figure 1), then press and hold down “–“ to check the pre-set pressure. See
#6 in figure 2. Adjust “+” or “–“ to set desired pressure.
5. Set the auto shut-off pressure level by pressing the “+” or “–“ buttons. Once the pre-set pressure is set, wait a few
seconds for the display to change back to zero.
6. Extend the air hose from its storage location and attach air hose nozzle to vehicle tire valve stem by threading the
nozzle onto the stem clockwise until secure. See #7 & #9 in figure 1.
NOTE: When the nozzle is connected correctly, wait 5-7 seconds and the gauge will indicate the current tire pressure. Al-
ways follow the manufacturer’s inflation pressure recommendations to avoid over-inflation. If the tire is over-inflated, press
the deflation bleeder valve button to release air until pressure gauge indicates the correct pressure. See #8 in figure 1.
The pressure gauge has a built-in memory and will default to the last tire pressure set in the pressure gauge display of the
inflator.
The pressure gauge on the inflator is for reference only and is therefore not binding for exact values. While inflating, the
gauge is a measurement of the fluctuating pressure between the tire and the high pressure hose. To reduce the risk of
over-inflation, use a reliable pressure gauge periodically during inflation before driving a vehicle inflated with the inflator.
7. Turn on inflator power switch to the HI position. See #2 in figure 1. The BellAire™ 7000 will now inflate your tire to
the pre-set pressure level and then shut off automatically. After pre-set auto shut-off has taken place, turn inflator
power switch to the off (middle) position. See #2 in figure 1.
8. To stop inflator before reaching the pre-set auto shut-off pressure, turn inflator power switch to the off (middle) posi-
tion. See #2 in figure 1.
9. Remove air hose nozzle from vehicle tire valve stem by turning air hose nozzle counterclockwise and return air hose
to its built-in storage location on inflator.
10. Turn off the inflator main power switch.
11. Properly store your tire inflator in the carry bag provided.
(Continued on page 11)

7
37000
WALL MOUNTING TEMPLATE
(Remove insert from instruction manual)
(Carefully remove Wall Mounting Template insert sheet from staple binding)

8
BellAire™ Model 7000 Tire Inflator Instructions
WALL MOUNTING TEMPLATE
123
4
NOTES:
• Wood wall stud mounting is recommended. Use keyhole slots 2 & 4. • Top edge of page = Top edge of inflator

9
37000
WALL MOUNTING INSTRUCTIONS
Your BellAire™ 7000 has been designed as a wall mountable inflator for ease of storage and charging the internal battery. See figure 5, page 3. The wall mounting template includes options for wood wall stud mount (recommended) or dry wall anchor mount. Drywall anchors or wood screws are not included in the inflator purchase. To mount inflator on a wood wall stud (recommended mounting):
1. Choose a suitable wall with a 110V power outlet that can be used to recharge inflator internal battery. 2. Choose a location on the wall that will be within reach of the 110V wall outlet. 3. Align the mounting template at the desired wall location ensuring the center of key hole slots 2 & 4 align with the center of the wood
wall stud.
4. Place a mark at the center “+” of the upper small circle of key hole slots 2 & 4. 5. Install #10 x 2” (minimum length) long screws into the wood wall stud at the marks for key hole slots 2 & 4. 6. Do not screw #10 screws completely into the wall. Stop the screw with the screw head about ¾” from the wall surface. 7. After inserting both screws, test the fit of the inflator by aligning the larger lower circle of key holes slots 2 & 4 with the head of the
screws in the wall.
8. Slide inflator down over the screws ensuring both screw heads are inserted inside each of the key slot openings. If the inflator feels loose, remove inflator and tighten screws into wall a little at a time and recheck the fit. Repeat this process until inflator mounting feels snug to the wall. If the inflator is too tight to hang, remove inflator and unscrew the screws a little at a time and recheck the fit. Repeat this process until inflator mounting feels snug to the wall. To mount to dry wall using drywall anchors (optional): 1. Choose a suitable wall with a 110V power outlet that can be used to recharge inflator internal battery. 2. Choose a location on the wall that will be within reach of the 110V wall outlet and provide maximum use of the coiled air hose length. 3. Align the mounting template at the desired wall location and place a mark at the center “+” of the upper small circle of key hole slots 1 &
3.
4. Install drywall anchors at marked locations with #10 x 2” (minimum length) long screws per the drywall anchor manufacturer’s instruc-
tions. Use caution and make certain the screws will not puncture anything behind the dry wall.
5. Do not screw #10 screws completely into drywall anchors. Stop the screw with the screw head about ¾” from the face of the anchor. 6. After inserting both screws, test the fit of the inflator by aligning the larger lower circle of key holes slots 1 & 3 with the head of the
screws in the wall.
7. Slide inflator down over the screws ensuring both screw heads are inserted inside each of the key slot openings. 8. If the inflator feels loose, remove inflator and tighten screws into anchors a little at a time and recheck the fit. Repeat this process until
inflator mounting feels snug to the wall. If the inflator is too tight to hang, remove inflator and unscrew the screws a little at a time and recheck the fit. Repeat this process until inflator mounting feels snug to the wall.
NOTE: Additional mounting strength may be obtained by using key hole slot # 2 OR #4 in addition to key hole slots #1 & #3 above and mounting one of them into a wood wall stud. You do not need to use a drywall anchor for key hole slot #2 or #4 when mounting into a wall stud. Use only a #10 x 2” (minimum length) long pan head wood screw.
(Carefully remove Wall Mounting Template insert sheet from staple binding)

10
BellAire™ Model 7000 Tire Inflator Instructions
WALL MOUNTING TEMPLATE
(Remove insert from instruction manual)
(Carefully remove Wall Mounting Template insert sheet from staple binding)

11
37000
(Continued from page 6)
INFLATING SPORTS BALLS OR OTHER HIGH PRESSURE SMALL INFLATABLES
USING A VEHICLE 12 VOLT DC CIGARETTE LIGHTER SOCKET TO INFLATE SPORTS BALLS AND OTHER
HIGH PRESSURE SMALL INFLATABLES:
1. Remove and unwind 12 Volt power cord from the storage compartment. See #22 in figure 1, page 3.
2. Extend air hose from its storage location (see #7 & #9 in figure 1) and select one of the small adapter needles pro-
vided in the storage compartment. See figure 3, page 3.
3. Attach the adapter needle to the air hose nozzle by turning the adapter needle clockwise.
4. Insert adapter needle into inflatable.
5. Make certain the inflator main and inflator power switches are both in the off position. See #1 & #2 in figure 1.
6. Set emergency brake and start vehicle engine. See “Warning: Vehicle Exhaust Without Proper Ventilation”, page 4.
7. Plug inflator lighter plug into vehicle 12 Volt cigarette lighter socket.
8. Turn on the main power switch only. See #1 in figure 1.
NOTE: When the nozzle is connected correctly, wait 5-7 seconds and the gauge will indicate the current inflatable item’s
pressure. Always follow the manufacturer’s inflation pressure recommendations to avoid over-inflation. If the inflatable
item is over-inflated, press the deflation bleeder valve button to release air until pressure gauge indicates the correct pres-
sure. See #8 in figure 1.
When inflating items requiring 10 PSI or less, inflate in short bursts and check by feel or by a reliable measuring device to
determine accurate pressure.
The pressure gauge has a built-in memory and will default to the last pressure set in the pressure gauge display of the
inflator.
The pressure gauge on the inflator is for reference only and is therefore not binding for exact values. While inflating, the
gauge is a measurement of the fluctuating pressure between the tire and the high pressure hose. To reduce the risk of
over-inflation, use a reliable pressure gauge periodically during inflation before driving a vehicle inflated with the inflator.
9. Check manufacturer’s recommended pressure specifications for inflatable.
10. Choose the desired pressure format (PSI, BAR, or KPA) by pressing the “R” button. Press “R” button until desired pres-
sure format appears on the LCD display. See #5 in figure 2.
IMPORTANT: The “R” re-set button should never be pressed while the air hose is connected to the inflatable and the
“R”,”+”, “–“ buttons should never be pressed while the inflator is running. If the “R” button is accidently pressed, turn the
inflator power switch only to the off position (see #2 in figure 1), then press and hold down “–“ to check the pre-set pres-
sure. See #6 in figure 2. Adjust “+” or “–“ to set desired pressure.
11. Set the auto shut-off pressure level by pressing the “+” or “–“ buttons. Once the pre-set pressure is set, wait a few
seconds for the display to change back to zero.
12. Turn on inflator power switch to the HI position. See #2 in figure 1. The BellAire™ 7000 will now inflate your inflat-
able item to the pre-set pressure level and then shut off automatically. After pre-set auto shut-off has taken place,
turn inflator power switch to the off (middle) position. See #2 in figure 1.
13. To stop inflator before reaching the pre-set auto shut-off pressure, turn inflator power switch to the off (middle) posi-
tion. See #2 in figure 1.
14. Remove air hose nozzle from inflatable, remove adapter needle from air hose nozzle by turning the adapter needle
counterclockwise, and return air hose and adapter needle to their storage locations on inflator.
15. Turn off the inflator main power switch. See #1 in figure 1.
16. Unplug inflator from vehicle 12 Volt cigarette lighter socket and store cord in its storage compartment.
17. Turn off vehicle.
18. Properly store your tire inflator in the carry bag provided.
USING THE INTERNAL RECHARGEABLE BATTERY TO INFLATE SPORTS BALLS, OR OTHER HIGH PRESSURE
SMALL INFLATABLES:
1. Extend air hose from its storage location (see #7 & #9 in figure 1, page 3) and select one of the small adapter needles
provided in the storage compartment. See figure 3, page 3.
2. Attach the adapter needle to the air hose nozzle by turning the adapter needle clockwise.
3. Insert adapter needle into inflatable.
NOTE: When the nozzle is connected correctly, wait 5-7 seconds and the gauge will indicate the current inflatable item’s
pressure. Always follow the manufacturer’s inflation pressure recommendations to avoid over-inflation. If the inflatable
item is over-inflated, press the deflation bleeder valve button to release air until pressure gauge indicates the correct

12
BellAire™ Model 7000 Tire Inflator Instructions
pressure. See #8 in figure 1.
When inflating items requiring 10 PSI or less, inflate in short bursts and check by feel or by a reliable measuring device to
determine accurate pressure.
The pressure gauge has a built-in memory and will default to the last pressure set in the pressure gauge display of the
inflator.
The pressure gauge on the inflator is for reference only and is therefore not binding for exact values. While inflating, the
gauge is a measurement of the fluctuating pressure between the tire and the high pressure hose. To reduce the risk of
over-inflation, use a reliable pressure gauge periodically during inflation before driving a vehicle inflated with the inflator.
4. Turn on the main power switch only.
5. Check the inflator to make certain green battery level indicator is on indicating a good battery power level. If the bat-
tery level indicator is not green, refer to directions under the “Rechargeable Battery Cautions” section on page 4 and
“Battery Indicator Light Chart” section on page 5.
6. Check manufacturer’s recommended pressure specifications for inflatable.
7. Choose the desired pressure format (PSI, BAR, or KPA) by pressing the “R” button. Press “R” button until desired pres-
sure format appears on the LCD display. See #5 in figure 2.
IMPORTANT: The “R” re-set button should never be pressed while the air hose is connected to the inflatable and the
“R”,”+”, “–“ buttons should never be pressed while the inflator is running. If the “R” button is accidently pressed, turn the
inflator power switch only to the off position (see #2 in figure 1), then press and hold down “–“ to check the pre-set pres-
sure. See #6 in figure 2. Adjust “+” or “–“ to set desired pressure.
8. Set the auto shut-off pressure level by pressing the “+” or “–“ buttons. Once the pre-set pressure is set, wait a few
seconds for the display to change back to zero.
9. Turn on inflator power switch to the HI position. See #2 in figure 1. The BellAire™ 7000 will now inflate your inflat-
able item to the pre-set pressure level and then shut off automatically. After pre-set auto shut-off has taken place,
turn inflator power switch to the off (middle) position. See #2 in figure 1.
10. To stop inflator before reaching the pre-set auto shut-off pressure, turn inflator power switch to the off (middle) posi-
tion. See #2 in figure 1.
11. Remove air hose nozzle from inflatable, remove adapter needle from air hose nozzle by turning the adapter needle
counterclockwise, and return air hose and adapter needle to their storage locations on inflator.
12. Turn off the inflator main power switch. See #1 in figure 1.
13. Properly store your tire inflator in the carry bag provided.
USING THE HIGH VOLUME/LOW PRESSURE RAFT INFLATOR
The high volume/low pressure raft inflator is used for inflating and deflating air mattresses, rafts and floats and cannot be
used for tires, sports balls or other items requiring higher pressures.
IMPORTANT: When the raft hose is connected to the low pressure ports of the BellAire™ 7000, the pre-set auto shut-off
system is not in use. Air pressure must be manually monitored to avoid over-inflation of items.
CAUTION: Never block the inflating or deflating ports while inflator is in operation.
INFLATING AIR MATRESSES, RAFTS AND FLOATS WITH THE RAFT INFLATOR
TO INFLATE USING A VEHICLE 12 VOLT DC CIGARETTE LIGHTER SOCKET:
1. Remove and unwind 12 Volt power cord from the storage compartment. See #22 in figure 1, page 3.
2. Remove the low pressure raft hose (see #24 in figure 1) from its storage location. See #19 in figure 1. Attach the ap-
propriate size raft adapter that comes connected to the raft hose. See figure 4, page 3.
3. Attach raft hose to the right “Inflate” port on the front of the inflator. See #16 in figure 1.
4. Insert raft adapter end of raft hose into item to be inflated.
5. Make certain the inflator main and inflator power switches are both in the off position. See #1 & #2 in figure 1.
6. Set emergency brake and start vehicle engine. See “Warning: Vehicle Exhaust Without Proper Ventilation”, page 4.
7. Plug inflator lighter plug into vehicle 12 Volt cigarette lighter socket.
8. Turn on the main power switch only. See #1 in figure 1.
9. Check manufacturer’s recommended pressure specifications for inflatable.
10. Turn on inflator power switch to the LO position. See #2 in figure 1. The BellAire™ 7000 will now inflate your inflat-
able using the high volume/low pressure inflator.
11. Stop inflator frequently to check inflatable air pressure by switching the inflator power switch to the middle position.
Remember to switch back to the LO position when turning inflator back on.

13
37000
12. Remove raft air hose nozzle from inflatable and return raft air hose to its storage location.
13. Turn off the inflator main power switch.
14. Unplug inflator from vehicle 12 Volt cigarette lighter socket and store cord in its storage compartment.
15. Turn off vehicle.
16. Properly store your tire inflator in the carry bag provided.
TO INFLATE USING THE INTERNAL RECHARGEABLE BATTERY:
1. Remove the low pressure raft hose (see #24 in figure 1, page 3) from its storage location. See #19 in figure 1. Attach
the appropriate size raft adapter that comes connected to the raft hose. See figure 4, page 3.
2. Attach raft hose to the right “Inflate” port on the front of the inflator. See #16 in figure 1.
3. Insert raft adapter end of raft hose into item to be inflated.
4. Turn on the main power switch only. See #1 in figure 1.
5. Check the inflator to make certain green battery level indicator is on indicating a good battery power level. If the bat-
tery level indicator is not green, refer to directions under the “Rechargeable Battery Cautions” section on page 4 and
“Battery Indicator Light Chart” section on page 5.
6. Check manufacturer’s recommended pressure specifications for inflatable.
7. Turn on inflator power switch to the LO position. The BellAire™ 7000 will now inflate your inflatable using the high
volume/low pressure inflator.
8. Stop inflator frequently to check inflatable air pressure by switching the inflator power switch to the middle position.
Remember to switch back to the LO position when turning inflator back on.
9. Remove raft air hose nozzle from inflatable and return raft air hose to its storage location.
10. Turn off the inflator main power switch.
11. Properly store your tire inflator in the carry bag provided.
DEFLATING AIR MATRESSES, RAFTS AND FLOATS WITH THE RAFT INFLATOR
TO DEFLATE AN INFLATABLE USING A VEHICLE 12 VOLT DC CIGARETTE LIGHTER SOCKET:
1. Remove and unwind 12 Volt power cord from the storage compartment. See #22 in figure 1, page 3.
2. Remove the low pressure raft hose (see #24 in figure 1) from its storage location. See #19 in figure 1. Attach the ap-
propriate size raft adapter that comes connected to the raft hose. See figure 4, page 3.
3. Attach raft hose to the left “Deflate” port on the front of the inflator. See #16 in figure 1.
4. Insert raft adapter end of raft hose into item to be deflated.
5. Make certain the inflator main and inflator power switches are both in the off position. See #1 & #2 in figure 1.
6. Set emergency brake and start vehicle engine. See “Warning: Vehicle Exhaust Without Proper Ventilation”, page 4.
7. Plug inflator lighter plug into vehicle 12 Volt cigarette lighter socket.
8. Turn on the main power switch. See #1 in figure 1.
9. Turn on inflator power switch to the LO position. See #2 in figure 1. The BellAire™ 7000 will now deflate your inflat-
able using the high volume/low pressure inflator.
10. Turn off the inflator power switch to stop inflator when the inflatable item has been adequately deflated.
11. Remove raft air hose nozzle from inflatable and return raft air hose to its storage location.
12. Turn off the inflator main power switch.
13. Unplug inflator from vehicle 12 Volt cigarette lighter socket and store cord in its storage compartment.
14. Turn off vehicle.
15. Properly store your tire inflator in the carry bag provided.
TO DEFLATE AN INFLATABLE USING THE INTERNAL RECHARGEABLE BATTERY:
1. Remove the low pressure raft hose (see #24 in figure 1, page 3) from its storage location. See #19 in figure 1. Attach
the appropriate size raft adapter that comes connected to the raft hose. See figure 4, page 3.
2. Attach raft hose to the left “Deflate” port on the front of the inflator. See #16 in figure 1.
3. Insert raft adapter end of raft hose into item to be deflated.
4. Turn on the main power switch only. See #1 in figure 1.
5. Check the inflator to make certain green battery level indicator is on indicating a good battery power level. If the bat-
tery level indicator is not green, refer to directions under the “Rechargeable Battery Cautions” section on page 4 and
“Battery Indicator Light Chart” section on page 5.
6. Turn on inflator power switch to the LO position. The BellAire™ 7000 will now deflate your inflatable using the high
volume/low pressure inflator.

14
BellAire™ Model 7000 Tire Inflator Instructions
TROUBLE SHOOTING
MAINTENANCE
The inflator fails to run with the inflator power switch turned on or digital pressure gauge does not illuminate:
• Check that the inflator’s main power switch is also on. See #1 in figure 1, page 3.
• Check that the plug is fully inserted into 12 Volt cigarette lighter socket. See operation instructions on pages 5-13.
• Your vehicle may require the ignition be turned to the accessory position for the cigarette lighter to have power. The
inflator should be used with the vehicle running.
• Check to see if the main fuse or if the fuse in the 12 Volt lighter plug has blown. See fuse replacement instructions in
the maintenance section. See figure 6 & 7, above.
• If using the internal battery for power, make certain the green battery level indicator is on. If not, see “Rechargeable
Battery Cautions” section on page 4 and “Battery Indicator Light Chart” section on page 5.
Inflator fails to stop at the auto shut-off pre-set pressure:
• Check to make sure auto shut-off pressure settings are being set correctly. See operation instructions on pages 5-13.
• Check that the correct pre-set pressure has been set.
12 Volt power cord gets hot:
• Makecertainpowercordisnotcoileduporinaknotordamaged.
1. Your BellAire™ 7000 has two replaceable fuses providing maximum protection for the inflator and/or your vehicle.
See figures 6 and 7 for fuse replacement instructions.
2. Regularly check inflator air hose, 12 Volt cord and adapters for damage.
3. Always keep the inflator in its carry case if not wall mounted.
4. Keep the inflator dry, clean and free from oil and grease. Always use a clean cloth when cleaning.
FIGURE 7 — 12 Volt Adapter Fuse Replacement
Turn tip counterclockwise to unlock Fuse Adapter Body
Fuse (Replace with ACG glass 15 amp fuse only)Adapter Body
FIGURE 6 — Main Fuse Replacement
Main Fuse (Replace with 15 amp blade type fuse only)
7. Turn off the inflator power switch to stop inflator when the inflatable item has been adequately deflated.
8. Remove raft air hose nozzle from inflatable and return raft air hose to its storage location.
9. Turn off the inflator main power switch.
10. Properly store your tire inflator in the carry bag provided.
USING THE LED WORK LIGHT
1. The (6) LED work light is located on the front lower edge of the inflator (see #13 in figure 1, page 3) and is operated
with a separate light switch. See #3 in figure 1. The light can be used by itself or used while inflating or deflating to
illuminate the work area.
2. The main power switch must be on in order for the work light to have power. See #1 in figure 1.
3. The work light is powered in either 12 Volt DC power or internal battery power mode.
4. The work light rotates for best directional lighting of your work area.

15
37000
WARRANTY
1-Year Limited Warranty
Bell Automotive® Products, Inc. warrants that for a period of one year from the date of original retail purchase, this
product will be free from defects in material and workmanship. Bell Automotive® Products, Inc., at its option, will repair
or replace this product or any component of the product found to be defective during the warranty period. Replace-
ment will be made with a new or remanufactured product or component. In the event the product is no longer available,
replacement may be made with a similar product. No warranty is provided on batteries and lighting components. This is
your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep
the original sales receipt. Proof of purchase is required to obtain warranty coverage.
What This Warranty Does Not Cover
This warranty does not cover normal wear of parts, parts that are not genuine Bell Automotive® parts, or damage result-
ing from any of the following: negligent use or misuse of the product; use on improper voltage or current; commercial use
of the product; use other than the operating instructions, disassembly, repair or alteration by anyone other than Bell Auto-
motive® Products, Inc. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.
Bell Automotive® Products, Inc. shall not be liable for any incidental or consequential damages caused by the breach
of any express or implied warranty or conditions, except to the extent prohibited by applicable law, any implied war-
ranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty or
conditions. Some states, provinces, or jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to
province.
The costs of transporting the product to Bell Automotive® Products, Inc. for warranty service are the responsibility of the
purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE
If you have any questions regarding this warranty please write or contact us through our website:
Bell Automotive® Products, Inc.
Attn: Customer Service
18940 N. Pima Road, Suite 200
Scottsdale, AZ 85255
www.bellautomotive.com
Pressure gauge appears to read incorrectly or is unreadable:
• Make certain when you attach the air hose nozzle to the tire stem that the gauge is reading the current tire pressure
before turning on the inflator switch. Main power switch must be on for pressure gauge to be on. See #1 in figure 1.
• Remove the 12 Volt plug from the power source for 5 seconds and plug back in.
The inflator is running but the tire is not inflating:
• Turn off the inflator and check that the air hose nozzle is securely attached to the tire valve stem.
Digital display shows ERR message:
• Insert the 12 Volt power plug into the vehicle’s 12 Volt lighter socket or power socket. Do not connect the air hose
nozzle to the tire valve stem. Let the gauge adjust for a few seconds. Press and hold the “R” reset button for a few
seconds. See #5 in figure 1. This will reset the pressure sensor. If the problem persists, the pressure sensor has failed.
Please contact Bell Automotive® Products customer service. See contact information section.

16
BellAire™ Model 7000 Tire Inflator Instructions
CONTACT INFORMATION
Bell Automotive® Products, Inc.
Attn: Customer Service
18940 N. Pima Road, Suite 200
Scottsdale, AZ 85255
www.bellautomotive.com
37000