Belmont Garden Create-A-Fountain User manual

Fountain Tower
Plumbers
Tape
Dancing Water
Attachments
Battery
Compartment
& Water Pump
CONTENTS:
Assembly
Water
Pump
Battery
Compartment
(4D Cell Batteries
Not Included)
Dancing Water
Attachments
Water Pump Tube
Vent Hole
Vent Hole
Battery Cover
Max Water Level
(Upper
Decorative
Ring)
Battery
Cover
Retaining
Nut
Bowl
(Not Included)
Recommended minimum bowl size is approximately 12 inches
Min Water Level
(Lower
Decorative
Ring)
Min Water Level
(Lower
Decorative
Ring)
Diagram 1a:
OWNERS MANUAL
Please note, images of parts are not to scale with one another.
INSTALLING BATTERIES:
1. Unscrew (counter clockwise) the
Battery Cover Retaining Nut and open cover
(Figure 1a, 1b).
2. Position the Battery Compartment with locating
dowel on top. (See Arrow Figure 1c &1d).
3. Insert 2 batteries (Figure 2a) with the (+) side
facing up in Battery Compartment (upper left and
lower right) and 2 batteries with the (-) facing up in
Battery Compartment (upper right & lower left).
4. Reinstall the Battery Cover by aligning the
locating dowel in the Battery Compartment and
Battery Cover. Set the Battery Cover down onto the
Battery Compartment ensuring the dowel sets into
the alignment hole. Tighten the Battery Cover
retaining nut by turning clockwise until you hear a
clicking sound. This indicates the Battery Cover is
sufficiently tight. (Figure 3a & 3b).
1. Take the Battery Compartment and Water Pump & connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the Battery Compartment (A & B of Figure 4).
2. Find a suitable bowl, place it on a flat level surface, place the Fountain without the Battery Compartment and Water
Pump, into the center of the bowl.
3. Lower the Battery Compartment and Water Pump into the Fountain and make sure it sits level on Fountain (Figure 5).
3. Fill bowl with water, water level should be between the upper and lower Decorative Rings on the outside of the
Fountain. This will ensure water covers the Water Pump (Diagram 1a).
OPERATING YOUR CREATE-A-FOUNTAIN:
Turn Fountain on and set timer: When the Fountain is off, set the run time for 1 to 4 hours by slowly pressing the button 1 to 4 times
(Figure 7a & 7b). 3 seconds after pressing the button, the LED light will repeatedly flash the number of times the button was pressed (Figure 7a).
This indicates the number of hours the Fountain will run every day. The Fountain will turn on at the same time, for the selected number of hours, daily thereafter.
Stop Fountain for one day: To stop the Fountain manually for one day, hold the button for over 2 seconds (Figure 7a & 7b). The Fountain will turn off for one day, but will still turn on at the
same time, for the same number of hours selected, daily thereafter.
Reset/Change the timer: To change the run time, stop the Fountain if its running by holding the button for over 2 seconds (Figure 7a & 7b). The Fountain will stop. Once the Fountain
stops, you can press the button again to set the duration. Refer to Turn Fountain on and set timer.
Fully shut off and clear timer: To fully turn off the Fountain so that it will not turn on automatically the next day, press and hold the button for over 2 seconds to turn it off (Figure 7a & 7b).
When the Fountain is NOT operating, simply press hold the button again for over 2 seconds, the LED light will come on for 3 seconds steady to confirm daily program is off.
DANCING WATER ATTACHMENTS: (OPTIONAL): To prevent overspray there are 3 Dancing Water Attachments designed for large bowls & 1 designed for small bowls please use accordingly.
When Fountain is not running, select one of the Dancing Water Attachments and attach to the outlet in the middle of the Fountain Tower (Figure 8a, 8b & 8c).
*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR NEW FOUNTAIN
Figure 6
Figure 5
Figure 1b
Figure 1a
Figure 3b
Figure 1c Figure 1d
Figure 4
Figure 3a
Figure 2b
STEP
2.
STEP
3.
STEP
Figure 2a
CHANGING BATTERIES:
1. Remove any Dancing Water Attachment, lift Battery Compartment
and Water Pump out of the Fountain (Figure 6). Ensure Battery
Compartment and Water Pump are completely dry before
opening Battery Compartment. It is important that no water
enters the Battery Compartment.
2. Reinstall batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 5).
Figure 7b
Figure 7a
LED
Light
LED
Light Button
Button
Need Help?
Call us for assistance at: 1+ [phone]
or you can email us at: customercare@
belmont.garden
Our Customer Care Department is available:
Monday - Friday 8:30am to 4:00pm PST 11:30am - 7:00pm EST
Locating
Dowel
Locating
Dowel
Locating
Dowel/
Alignment
Hole
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Battery Cover
Retaining Nut
Dancing Water Attachments
Please use accordingly
to prevent overspray
Large Bowls Small Bowls
Figure 8a Figure 8b Figure 8c
17 in (43.18cm)
diameter or
larger bowls
11.5 in (29.21cm)
to 17 in (43.18cm)
diameter bowls
Create-A-FountainTM
Locating
Dowel/
Alignment
Hole

Troubleshooting Troubleshooting Guide
OWNERS MANUAL
4.
STEP
Care and Maintenance
5.
STEP
001175 BGCAFFI rev 3a us
Santee, California 92071 | World Wide Patents Pending | Email: customercare@ belmont.garden | On the web: www.belmont.garden
Facebook & Pinterest: Belmont Garden | Instagram: @
belmontgarden Twitter: @yrdllc
© Yeiser Research & Development, LLC; 2019. All rights reserved.
Made in China | Designed in the USA
Create-A-FountainTM
Please read first before returning:
Please call us for assistance at 1+ [phone] or email us at customercare@ belmont.garden . Our Customer Care Department is available: Monday - Friday 8:30am to 4:00pm PST, 11:30am to
7:00pm EST. If you have any questions regarding assembly, parts, or operation, please visit our website at www.
belmont.garden . You will find instructional videos on how to assemble and operate
your fountain, and it will keep you up to date on our newest products. You can also email us with any questions you have. This product comes with a one year limited warranty against materials and
workmanship.
LIMITED ONE YEAR WARRANTY
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This product has a one year limited warranty on all materials and workmanship.
Belmont Garden
TM
warrants the original purchaser of this product that the product will be free from manufacturing defects in workmanship and material for a period of one (1) year from the date of
original purchase. If within one (1) year this product fails due to defect in material or workmanship, Belmont Garden
TM
will repair, replace or supply any defective part at their discretion. The
purchaser must contact Belmont Garden
TM
and provide a description of the defective part, including digital pictures if requested, with the original purchase documentation as validation of warranty
coverage. This warranty does not cover or apply to: (a) damage to the product due to misuse, mishandling, or abuse, (b) products not used in accordance with instructions, (c) product not
assembled or installed according to instructions, and (d) normal wear and tear. Call us for assistance at 1+ [phone] or email us at [email protected] or mail us at: 9545
Pathway Street, Santee, CA 92071, Our Customer Care Department is available: Monday - Friday 8:30am to 4:00pm PST / 11:30am - 7:00pm EST
IMPORTANT BATTERY SAFETY INSTRUCTIONS:
PROPOSITION 65 WARNING: This product can expose you to chemicals including lead and lead compounds which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www. P65Warnings.ca.gov.
WARNING: When using electric devices, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following:
WARNING: 1. Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery can explode in a fire. Check with municipal codes in your area for possible special disposal
instructions.
2. If liquid leaks from the battery cell, discontinue use immediately and dispose of properly.
3. Use only 4-1.5V D Cell Batteries.
4. Do not attempt to disassemble, remodel or destroy the batteries, as it may cause battery leakage, fire, or bursting; and could also create sulfuric acid spills from the battery resulting in possible burns to
person and damage to the immediate environment.
5. Never dispose of batteries in the garbage. Disposal of batteries in the garbage is unlawful under state and federal environmental laws and regulations. Always take used batteries to your local battery-re-
cycling center.
Step 1 Step 2 Step 3
Step 1
Step 4
Step 2
CLEANING YOUR FOUNTAIN
In order to keep your Fountain in tip-top shape and for a prolonged life, it is best if your Fountain
and the bowl or water container that the Fountain is placed in are cleaned periodically. To clean
your fountain, drain of all water and disassemble. Use a mild soap and a soft cloth to clean the
parts of your Fountain.
COLD STORAGE
Turn power off, remove from container, clean and dry the Fountain of all water. Remove the
batteries for long term storage and bring it indoors. (Now is a great time to clean the pump to
remove any debris that may have accumulated throughout the year).
CLEANING THE WATER PUMP’S PARTS
The impeller inside of the Water Pump is what pushes water up through your Fountain, allowing
you to enjoy the soothing sounds and wonderful sights of your Fountain. After long periods of
usage, this part will need to be cleaned to make sure your Fountain runs optimally.
Step 1: Remove the front panel of the Water Pump by grabbing the sides of the front panel and
pulling it off the unit.
Step 2: Remove the impeller chamber cover. This is tightly fitted but will come off.
Step 3: Remove the impeller from its chamber.
Step 4: Rinse the impeller until all debris has been removed.
Step 5: Re assemble in reverse order.
BATTERY COMPARTMENT MAINTENANCE:
Simply apply approximately 10” of pipe tape (also called Plumbers Tape) around the
spindle located in the middle of the bottom piece of the battery compartment. Apply the
tape so that you cover the two O-rings completely; you DO NOT need to cover the threads
on the spindle. We recommend you do this every time you replace your batteries. An extra
10” of Plumbers Tape has been included with packaging for future battery changes.
PRIMING THE WATER PUMP
If you find the Water Pump is running, but water is not
flowing from your Fountain, you can try priming the Water
Pump:
Turn off Fountain, grab both sides of the Fountain and
quickly shake your Fountain for ten seconds. This is to
dislodge any air bubbles that may be caught in your Water
Pump. Press the button to turn your Fountain on. Water
should be flowing from the top of your Fountain. If water is
not flowing, press and hold button for over 2 seconds
again to turn your Fountain off, and repeat the step above.
WATER PUMP CONNECTION
If your Fountain Water Pump becomes disconnected from
the Water Tube inside of the Fountain or if the Water Tube
gets disconnected from the Battery Compartment, go to
the Assembly Section to reconnect the Water Pump.