Beltone myPAL Pro User manual

Beltone myPAL Pro
Instructions for use

2 3
Statement:
This device complies with Part 15 of the FCC Rules and ICES-003
of the IC Rules. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including inter-
ference that may cause undesired operation.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of the IC rules. These limits are de-
signed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the re-
ceiver.
Welcome
Congratulations on your purchase of a Beltone myPAL Pro. The
myPAL Pro is a high quality portable speech and audio streamer
that streams speech and audio directly to your hearing instru-
ment. It supports both one-to-one communication when worn by
a single speaker and can also be used as a table microphone
solution picking up speech from multiple speakers.
Additionally, the myPAL Pro supports pickup of tele-loop signals,
FM signals (Europin FM receiver required) and line-in signals
(mixed mono).
Please read this manual carefully to fully benefit from the myPAL
Pro. Ask your hearing care professional if you have any questions.
For further information you can also visit the
www.beltone-hearing.com web site.
For your safety, carefully read the chapter Important Information,
starting on page 33.
FCC ID : X26SM-2P

4 5
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference
that may cause undesired operation of the device.
For other identified applicable international regulatory require-
ments in countries outside EU and US, please refer to local coun-
try requirements for these areas.
In JP: Japanese Radio Law and Japanese Telecommunications
Business Law Compliance.
This device is granted pursuant to the Japanese Radio Law
(電波法) and the Japanese Telecommunications Business Law
(電気通信事業法). This device should not be modified (otherwise
the granted designation number will become invalid).
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications can void the user’s authority to operate
the equipment.
Intended use
To enable hearing instrument users to follow speech or listen to
other audio signals.
This product is in compliance with the following regulatory re-
quirements:
In EU: The device conforms to the Essential Requirements ac-
cording to Annex I of Council Directive 93/42/EEC for medical
devices (MDD) and Essential Requirements and other relevant
provisions of Directive 1999/5/EC (R&TTE).
The declaration of conformity may be consulted at
www.beltone-hearing.com
In US: FCC CFR 47 Part 15, subpart C
In Canada: IC 6941C-SM2P

6 7
Welcome..........................................2
Statement .........................................3
Intended use .......................................4
Description ........................................8
Getting Started ....................................10
Turning your myPAL Pro ON and OFF...................12
Pairing to your hearing instruments.....................12
Start streaming ....................................15
Stop streaming ....................................16
Microphone directionality ............................18
Wearing the Multi Mic ...............................18
Status light indicator (LED) ...........................20
Modes of operation.................................22
Using the Mode button ..............................24
Volume control and mute ............................26
Mute light indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Special features ...................................28
Test mode........................................31
Important Information ...............................33
General warnings ..................................34
General precautions ................................35
Built-in battery care ................................36
Battery warning....................................37
Charger care......................................38
Technical specifications .............................40
Temperature test, transport and storage information .......40
Warranty .........................................40
What is covered by this warranty? .....................41
What is not covered by the warranty....................41
Troubleshooting guide ..............................42
Contents

8 9
7 Volume down
8 Mute button
9 Volume up
10 Micro USB for charging
11 Mute light indicator (LED)
12 Mode and battery status light indicators (LEDs)
13 Mode button
14 Paring button
15 Mounting clip
Description
1 Power button
2 Microphone inlet
3 Microphone inlet
4 Status light indicator (LED)
5 Line-in
6 FM connector
1
6
4
2
814
11 12
15
13
10
79
3
5

10 11
Getting Started
Before using your myPAL Pro, you need to charge the recharge-
able battery. To charge it, plug the charging cable into the myPAL
Pro as shown in the picture below.
Next, plug the other end of the charging cable into the charger
and into a power outlet.
During the charging process, the status LED indicator will show
a solid red light. When fully charged and still connected to the
charger, the LED will turn solid red, interrupted by a green blink
every 2 seconds.
Charging an empty battery typically takes about 3 hours. It is safe
to leave the charger connected overnight –
the battery cannot be overcharged.
• When charging your myPAL Pro for the first time, let it charge
for at least 3 hours, even if the battery indicator indicates that
the battery is fully charged.
• For safety reasons, recharge the battery only with chargers
supplied by Beltone.
iNote: To protect the myPAL Pro when not in use, please
place it in the carrying pouch delivered with the product.
Do not charge the myPAL Pro while it is on your body.

12 13
Turning your myPAL Pro ON and OFF
To turn the myPAL Pro ON, press and hold the Power button (see
page 8) for approximately 1.5 seconds, until the status LED turns
green. After releasing the Power button, the status LED will blink
green every 2 seconds.
To turn the myPAL Pro OFF, press and hold the ON/ OFF button
for approximately 1.5 seconds, until the status LED turns red –
indicating that the unit is shutting down.
If the battery level is low, the status LED will blink orange once
every second.
Pairing to your hearing instruments i
Note! The following information is primarily intended for your hear-
ing care professional, who in most cases will complete the nec-
essary tasks needed before the myPAL Pro can be used with
your hearing instruments. However, the process is designed to be
simple and most people can do it themselves.
It is possible to pair up to three Beltone streaming devices - e.g.
one myPAL Pro and two TV Link 2s (optional Direct™ accessory)
- with a given pair of hearing instruments. Therefore, channel 1, 2
or 3 must be selected when starting the pairing process.
Pairing the myPAL Pro in channel 1
1. Make sure the myPAL Pro is turned ON. Your hearing instru-
ments must be OFF – open the battery doors.
2. With the tip of a pen
or similar object, press
the small pairing but-
ton once, as shown in
the picture to the right.
The status LED will now
blink orange once every
2 seconds to indicate that
the myPAL Pro is ready
to be paired in channel 1.
Your myPAL Pro will remain in Pairing mode for 20 seconds.
3. While in Pairing mode, close the battery doors on both hear-
ing instruments and make sure they are ON. A successful
pairing will be indicated by an audible melody being played
in both hearing instruments and the status LED (see page 8)
will stay solid orange for 3 seconds. You are now ready to use
the myPAL Pro!

14 15
Start streaming
Turn ON the myPAL Pro and make sure your hearing instruments
are turned ON. Streaming can be started in one of three ways.
1. Press and hold the push or toggle button on both hearing
instruments for about three seconds in order to listen to a
streamed audio signal*. If ear to ear program coordination is
activated in you hearing instruments, you only have to activate
streaming on one of the hearing instruments.
2. If you have a Beltone Direct™ Remote Control (optional
accessory), simply press the streaming button on the
Remote Control*.
3. If you use a Beltone app offering remote control functionality,
simply select the myPAL Pro program in the program screen*.
*Once the hearing instruments connect to the myPAL Pro, a short
“streaming activation” melody will play in your hearing instru-
ments followed by the streamed sound.
Start streaming from a 2nd or 3rd streaming device
If your hearing instruments are paired to more than one stream-
ing device, you can start streaming from one of these devices in
three ways.
Pairing button
pushes Light indicator pattern Channel
1 1
2 2
3 3
Successful
pairing
Indication
Pairing the myPAL Pro in channel 2 or 3 (For people using more
than one streaming device)
To pair the myPAL Pro in channel 2, press the pairing button
twice. The status LED will now blink yellow twice every 2 seconds
to indicate that it is ready to be paired in channel 2. Close the bat-
tery doors on the hearing instruments.
To pair the myPAL Pro in channel 3, press the pairing button three
times. The LED will now blink yellow three times every 2 seconds
to indicate that it is ready to be paired in channel 3. Close the bat-
tery doors on the hearing instruments.
Pairing blinking pattern:

16 17
1. Press and hold the hearing instrument program button for
about 3 seconds two or three times in a row to access the 2nd
or 3rd Beltone streaming device.
2. If you use a Direct™ Remote Control (optional accessory),
press the streaming button on the Direct™ Remote Control
a 2nd or 3rd time to access the 2nd or 3rd Beltone streaming
device.
3. If you use a Beltone app offering remote control functionality,
simply select the desired streaming program in the program
screen.
Stop streaming
Streaming can be stopped in the following three ways:
1. Push the program button on your hearing instruments once*.
2. If you have a Beltone Direct™ Remote Control (optional ac-
cessory), press the “P” button, located in the center of the key
pad*. You may also press the home button to return to your
default settings.
3. If you use a Beltone app, select the desired program in the
program screen.
*This will return the hearing instruments to the last program used.
iNote! You may get out of range from your myPAL Pro. If your
myPAL Pro gets out of range and in range again within 5 minutes,
your hearing instruments will automatically reconnect and con-
tinue streaming. This also applies if the myPAL Pro is turned off
and on again within 5 minutes.

18 19
Microphone directionality
The myPAL Pro can both be used for picking up the voice from
one speaker wearing the myPAL Pro as well as a table micro-
phone solution picking up the voices of multiple speakers.
Wearing the Multi Mic
Using the myPAL Pro with one speaker
When the myPAL Pro is used for listening to one speaker of inter-
est, it should be clipped onto the speaker’s shirt. Alternatively,
the myPAL Pro can be hung around the speakers neck using the
lanyard supplied with the device.
Place the device within a range of 10-40cm (4-16 inches) from
the speaker’s mouth as shown on the next page. When using the
clip, make sure that the myPAL Pro is mounted vertically with the
Status LED pointing towards the mouth.
When worn vertically, the myPAL Pro automatically switches into
a mode minimizing background noise.
10 - 40 cm
4-16 inches
Using the myPAL Pro as a table microphone
Place the myPAL Pro horizontally on a level surface (e.g. a table) in
close proximity to the group of people you want to listen to. Plac-
ing the myPAL Pro horizontally on a table automatically switches it
into a mode optimized for picking up the voices of multiple speak-
ers.

20 21
Status light indicator (LED)
The LED on your myPAL Pro serves as a multipurpose user inter-
face, providing information on the status of your device.
Power/Charging No charging Charging Fully charged
Powered Off
Powered On (Normal)
Powered On
(Volume control disabled and MIC or
FM mode selected)
Powered On (Low battery) No LED indication No LED indication
Powered On (Low battery)
(Volume control disabled and Mic or
FM mode selected)
No LED indication No LED indication
Volume control locked or unlocked
(See page 28)
Turning power ON indication 3 seconds 3 seconds 3 seconds
Turning power OFF indication 3 seconds 3 seconds 3 seconds
Test mode (See page 31) Constant lit Constant lit Constant lit

22 23
Modes of operation
The myPAL Pro is a versatile speech and audio streamer offering
both microphone pickup while worn vertically on the body, or as
a table microphone while placed horizontally on e.g. a table. It
also offers extended audio source connectivity options by being
able to receive telecoil signals, FM signals (optional FM receiver
needed) and connecting to auxiliary audio sources through the
built-in mini-jack line input. It is possible to stream speech and
audio in the following ways:
From the built-in microphones
In microphone mode the myPAL Pro will send sound from
the environment to the hearing instruments. The myPAL
Pro will optimize the speech pick-up depending on how it is
used. When wearing it vertically on the body (using the clip
or the lanyard) the myPAL Pro will be in a mode, minimizing
background noise.
When placed horizontally on a table, the myPAL Pro will
switch into an optimized Table mode, enabling pick-up of
speech from more speakers placed around the unit.
From the built-in Telecoil, receiving audio from a teleloop
system (available at e.g. some theatres, schools, churches,
etc.). Note: Telecoil mode will not be available when the
Multi Mic is charging.
From an external, analogue audio source. In line-in mode
the myPAL Pro can receive audio from an audio device
such as a mobile phone, MP3 player, tablet, computer or
TV. To use this mode, the audio device must be connected
to the myPAL Pro using a mini-jack cable (included with the
myPAL Pro). When an audio device is connected, line-in
mode will automatically be selected. Other modes can be
selected by clicking on the mode button until the desired
mode is reached. In this mode, the hearing aid user will
wear the myPAL Pro or have it nearby.
From an external FM receiver. In FM mode the myPAL Pro
can receive audio from a FM transmitter. This requires
that an FM receiver (optional accessory) is attached to the
myPAL Pro via the 3-pin Euro pin connector. When the re-
ceiver is inserted the FM mode will automatically be select-
ed. Other modes can be selected by clicking on the mode
button until the desired mode is reached. In this mode the
hearing aid user will wear the myPAL Pro or have it nearby.
The myPAL Pro will now be able to transmit the received
FM signal to the hearing instruments.
iNote: Line-in and FM modes can only be selected if a cable
or an FM receiver is inserted into the myPAL Pro.

24 25
Using the Mode button
The Mode button (see page 9) is utilized to view current mode,
switch between different input modes and check the battery sta-
tus of the myPAL Pro.
Current mode:
To view the current mode of operation, press the Mode but-
ton once. The corresponding mode LED on the backside of the
myPAL Pro will light up for 3 seconds.
Changing mode:
To change the mode of operation, do the following:
1. Press the Mode button once. The Mode LED corresponding
to the current mode will be lit.
2. Within 3 seconds, press the Mode button again to change
mode.
3. Repeat step 2 until the desired mode is obtained.
Checking the battery status
To view the current battery status press and hold the Mode but-
ton for at least 3 seconds until one or more of the Mode LEDs
starts to blink.
- 75 – 100 % remaining battery capacity: All Mode LEDs blink
- 50 – 75 % remaining battery capacity: Three Mode LEDs
blink (FM + Line-in + TC)
- 25 – 50 % remaining battery capacity: Two Mode LEDs blink
(FM + Line-in)
- <25 % remaining battery capacity: One Mode LED blinks
(FM)
iNote: When less than 30 minutes of operating time is left
(low battery condition) the status LED will start blinking orange
(see Light Indicator chapter).

26 27
iNote: The myPAL Pro will revert to its default level for all
modes when restarted.
The Beltone Direct™ Remote Control (optional accessory) can
also be used to adjust the streaming volume in the hearing instru-
ment. Please ask your hearing care professional for more infor-
mation about this accessory.
Mute
The signal from the myPAL Pro can be muted, should the wearer
of the device want to engage in conversations or activities irrel-
evant for the hearing instrument user.
• To mute the signal press the Mute button (see page 9) once.
The Mute LED will now start blinking orange.
• To unmute the signal press the Mute button once. The Mute
LED will now stop blinking orange.
Note: Changing mode or restarting the myPAL Pro, while muted,
will unmute the signal.
Volume control and mute
Volume control
myPAL Pro is designed to provide a comfortable listening level
from the moment it is activated. However, for some devices or lis-
tening environments you may want to adjust the volume. This can
be accomplished in a variety of ways. Keep in mind that volume
adjustments apply to the streamed signal only.
• Use the “+” and “-“ buttons (see page 9) to adjust volume to a
comfortable level.
Every volume change on the on the myPAL Pro will be indicated
by a short blink of the Mute LED. When reaching the maximum or
minimum volume level the Mute LED will show a longer (1 second)
steady orange light.
Volume
Blink

28 29
Mute Light indicator
Configuration/Blinking pattern Mute Light indicator
Normal Operation (Unmuted)
Normal Operation (Muted)
Special features
Drop detection
In the event that the myPAL Pro falls from a height of more than
75 cm (30 inches), a built-in sensor will mute the output streamed
to the hearing instruments for up to 2 seconds. This is done to
protect the hearing instrument user from very loud and unpleas-
ant impact noise should the unit be accidentally dropped during
use.
Volume control lock
If needed, the volume of the myPAL Pro can be locked to a spe-
cific level.
The volume level can be locked for Microphone and FM mode
only. When the volume control is locked, it will be fixed to the level
it had when the myPAL Pro was powered OFF, but it is still pos-
sible to use the mute/unmute functionality of the device.
How to lock the volume control
• Make sure the myPAL Pro is turned OFF.
• Press and hold the volume ‘-‘ button and the Power ON button
for 1.5 seconds until the status LED turns green (myPAL Pro
powering up) and release the Power button.
• Keep pressing the volume ‘-‘ button until a green-orange-red
LED sequence is shown on the status LED after 10 seconds.
The status LED will now blink twice every 2 seconds to indicate
that the volume control is locked.
How to unlock the volume control
• Make sure the myPAL Pro is turned OFF.
• Press and hold the volume ‘+‘ button and the Power ON but-
ton for 1.5 seconds until the status LED turns green (myPAL
Pro powering up) and release the Power button.
• Keep pressing the volume ‘+‘ button until a green-orange-red
LED sequence is shown on the status LED after 10 seconds.
The volume can be adjusted independently for Mic and FM mode.
When locked, the volume levels for both Mic mode and FM mode

30 31
Test mode
The Test mode is primarily intended to be used for pediatric trans-
parency measurements. The transparency measurement evalu-
ates if the hearing instrument and wireless (remote) microphones
provide equal outputs when presented with the same 65 dB SPL
input stimulus.
When in Test mode the microphone is set to omnidirectional
mode with 0 dB gain when placed horizontally in the test cham-
ber. Please refer to relevant guidelines for performing transpar-
ency measurements.
How to enter Test mode:
• Make sure the myPAL Pro is turned OFF.
• Press and hold the Mute button and the Power button for 1.5
seconds until the status LED turns green and then release the
Power button.
• Keep pressing the Mute button until the green-orange-red se-
quence is shown on status LED after 10 seconds.
• When in Test mode the Status LED (see page 8) will be solid
orange.
• When entering Test mode the default volume is applied. If
needed, volume can be adjusted on the myPAL Pro until trans-
parency has been verified.
will be locked at the volume levels last used or set for each of
these modes.
The volume levels for TC mode and Line-in mode can still be
changed as described in the Change Volume section even if the
volume is locked for Mic mode and FM mode.

32 33
• To exit Test mode and save settings turn off the myPAL Pro
and lock the volume control (see Volume control lock section
in the Special features chapter).
iNote: Adjustments to reach transparency can be made on
the myPAL Pro and/or in the hearing instrument using the fitting
software.
Important Information
Maintenance and Care
• Clean the myPAL Pro using a dry cloth. Never use household
cleaning products (washing powder, soap etc…) or alcohol to
clean the device.
• When the myPAL Pro is not in use, turn it OFF and store it
safely.
• Protect the myPAL Pro from excessive moisture (bathing,
swimming) and heat (radiator, car dashboard).
• Protect it from excessive shock and vibration.
• Protect the microphone and charger inlets from debris and
dirt. If necessary, use the cleaning brush provided with your
hearing instruments to clean these areas.

34 35
General warnings i
• Keep this device out of reach of children under 3 years.
• Young children can wrap cords and lanyards/key chains
around their neck causing the risk of strangulation. Therefore,
always keep cords and lanyards/key chains out of reach of
children.
• The myPAL Pro may be interfered by other equipment.
• myPAL Pro uses low-powered digitally coded transmissions in
order to communicate with other wireless devices. Although
unlikely, nearby electronic devices may be affected. In that
case, move the myPAL Pro away from the affected electronic
device.
• When using myPAL Pro and the device is affected by electro-
magnetic interference, move away from the source.
• Avoid exposing your product to rain, moisture or other liquids
to protect against damage to the product or injury to you.
• Keep the product and any cords and cables away from oper-
ating machinery.
• If the product overheats, if the product is dropped or dam-
aged, if the product has a damaged cord or plug, or if the
product is dropped in a liquid, discontinue use and contact
your hearing care professional.
• Do not use in areas where there are explosive hazards or
where there is a danger of ignition of flammable gasses.
General precautions i
• Do not use this device in locations where it is forbidden to use
electronic devices.
• X-ray radiation (e.g. CT scans, MRI scans) may adversely af-
fect the correct functioning of this device. We recommend
that you switch the device OFF before undergoing X-ray pro-
cedures and keep it outside the room.
• High-powered electronic equipment, larger electronic instal-
lations and metallic structures may impair and significantly
reduce the operating range.
• If the hearing instruments do not respond to the device be-
cause of an unusual field disturbance, move away from the
disturbing field.
• Your hearing instruments and this device were given a unique
communication code during the fitting. This ensures that the
device will not affect hearing instruments worn by others.
• Do not make any changes or modifications to this device.
• Opening the myPAL Pro may damage it. If problems occur
which cannot be resolved, consult your hearing care profes-
sional.

36 37
• myPAL Pro may only be repaired by an authorized service
center.
• Do not use myPAL Pro in areas where RF transmission is pro-
hi-bited, e.g. air planes etc.
• Do only connect myPAL Pro to connections, which it is explic-
itly intended for.
Built-in battery care i
Please observe the following if the product contains a battery
• Your product is powered by a rechargeable battery.
• The full performance of a new battery is achieved only after
two or three complete charge and discharge cycles.
• The battery can be charged and discharged hundreds of
times, but will eventually wear out.
• Unplug the charger from the electrical plug and the product
when not in use.
• If left unused, a fully charged battery will lose its charge over
time.
• Leaving the product in hot places, such as in a closed car
during hot summer conditions, will reduce the capacity and
lifetime of the battery.
• A product with a cold battery may not work temporarily, even
when the battery is fully charged. Battery performance is par-
ticularly limited in temperatures well below freezing.
Battery warning i
• ”Caution” – The battery used in this product may present a risk
of fire or chemical burn if mistreated.
• Do not attempt to open the product or replace the battery.
It is built-in and not changeable. Use of other batteries may
present a risk of fire or explosion and the warranty will be ter-
minated.
• The battery in your product can not be removed or replaced
by the user. Any attempt to do so is risky and may result in
damage of the product.
• Only recharge the myPAL Pro with a power supply unit that
has been supplied together with the product.
• Dispose of batteries according to local regulations. Please re-
cycle when possible.
• Do not dispose the battery as household waste or in a fire as
it may explode.
• Batteries may explode if damaged.

38 39
Charger care i
Please observe the following if the product is supplied with a
charger
• Do not attempt to charge your product with anything other
than the AC adapter provided. The use of any other types
may damage or destroy the product and could be danger-
ous.
• Use of other chargers may invalidate any approval or war-
ranty.
• For availability of approved enhancements, please check
with your hearing care professional.
• Charge the product according to the instructions supplied
with the product.
Charger warning i
Use the device only with the power supply unit that has been
supplied together with the product. The use of any other types
may damage or destroy the product and could be dangerous.
Use of other power supplies may invalidate any approval or
warranty.
• When you disconnect the power cord, grasp and pull the plug,
not the cord.
• Never use a power supply that is damaged.
• Do not attempt to disassemble the power supply as it may
expose you to dangerous electric shock.
• Incorrect reassembly can cause electric shock or fire when
the product is subsequently used.
• Avoid charging your product in extremely high or low tempera-
tures and do not use the charger outdoors or in damp areas.
Do not charge the myPAL Pro while it is on your body.