Benchmark 1280-002 User manual

READ ALL INSTRUCTIONS BEFORE FIRST USE.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
KEEP AWAY FROM CHILDREN.
WEAR CSA APPROVED
EYE PROTECTION
WEAR EAR
PROTECTION
WEAR A
FACE MASK
3042597
JD2480UH
5 year limited warranty on tool
OSCILLATING
MULTI-TOOL KIT

1
PRODUCT SPECIFICATIONS
OSCILLATING MULTI-TOOL KIT
Rating 120 V, 60 Hz AC
Amperes 3.0
Variable speed 11,000–21,000 OPM (no load)
Oscillating angle 3.2°
Weight 5 lb 2 oz (2.3 kg)
NEED ASSISTANCE?
Call us on our toll- free customer support line:
1-866-349-8665 (Monday through Friday 9am – 5pm Eastern Standard Time)
• Technical questions
• Replacement parts
• Parts missing from package

1280-002
OSCILLATING MULTI-TOOL KIT
2
TABLE OF CONTENTS
Product Specifications................................................................................... 1
Table of Contents........................................................................................... 2
General Safety Warnings ................................................................................ 3
Eye, Ear & Lung Protection............................................................................. 3
Power Tool Safety........................................................................................... 3
General Safety Rules...................................................................................... 3
Electrical Safety and Extension Cord Guidelines ............................................. 4
Work Area Safety ........................................................................................... 4
Electrical Safety............................................................................................. 4
Personal Safety ............................................................................................. 5
Power Tool Use and Care................................................................................ 5
Service ......................................................................................................... 6
Specific Safety Rules for Oscillating tools ....................................................... 6
Symbols......................................................................................................... 7
Know your Oscillating Tool ............................................................................. 8
Assembly and Operating ................................................................................ 9
Installing Accessories..................................................................................... 9
Installing Sandpaper .................................................................................... 10
.............................................................................................. 10
Led Work Light............................................................................................. 10
Speed Control Wheel ................................................................................... 11
Flush Cutting a Door Jamb and Casing for Installing Flooring......................... 12
Cutting a Hole in Wood Flooring to Install a Heating Vent .............................. 13
Cutting a Hole in Drywall for Installing an Electrical Outlet Box...................... 14
Using the Detail Sander Attachment............................................................. 15
Using the Scraper Blade............................................................................... 15
Maintenance ............................................................................................... 16
Exploded View ............................................................................................. 19
Parts List ..................................................................................................... 20
Warranty ..................................................................................................... 22

3
GENERAL SAFETY WARNINGS
WARNING: Before using this tool or any of its accessories, read this manual
and follow all Safety Rules and Operating Instructions. The important precautions,
safeguards and instructions appearing in this manual are not meant to cover all
possible situations. It must be understood that common sense and caution are
factors which cannot be built into the product.
EYE, EAR & LUNG PROTECTION
SYMBOL MEANING
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA
Z94.3 or ANSI SAFETY STANDARD Z87.1
FLYING DEBRIS can cause permanent eye damage. Prescription
eyeglasses ARE NOT a replacement for proper eye protection.
Non-compliant eyewear can cause serious injury if broken during
the operation of a power tool.
Use hearing protection, particularly during extended periods of
operation of the tool, or if the operation is noisy.
WEAR A DUST MASK THAT IS DESIGNED TO BE USED WHEN
OPERATING A POWER TOOL IN A DUSTY ENVIRONMENT.
Dust that is created by power sanding, sawing, grinding, drilling, and
other construction activities may contain chemicals that are known
to cause cancer, birth defects, or other genetic abnormalities. These
chemicals include:
• Lead from lead-based paints
• Crystalline silica from bricks, cement, and other masonry products
• Arsenic and chromium from chemically treated lumber.
The level of risk from exposure to these chemicals varies, according to
how often this type of work is performed. In order to reduce exposure
to these chemicals, work in a well-ventilated area, and use approved
safety equipment, such as a dust mask that is specifically designed to
filter out microscopic particles.
To avoid electrical hazards, fire hazards or damage to the tool,
use proper circuit protection.
This tool is wired at the factory for 120 V AC operations. It must be
connected to a 120 V AC, 15 A circuit that is protected by a time-
delayed fuse or circuit breaker. To avoid shock or fire, replace power
cord immediately if it is worn, cut or damaged in any way.

1280-002
OSCILLATING MULTI-TOOL KIT
4
VOLTS Total Length of Cord in Feet (meters)
120V 25' (7.5 m) 50' (15 m) 100' (30 m) 150' (45m)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Amperage rate American Wire Gauge
More than Not more than
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains operated(corded) power tool or battery-
operated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark are as invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerator. There is an increased risk of electric shock if your body
is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges and moving parts.
Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
•
If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.

5
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
•
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
• If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection
can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it
was designed.
•
that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts,
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be

1280-002
OSCILLATING MULTI-TOOL KIT
6
could result in a hazardous situation.
• Hold power tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with
a "live" wire will make exposed metal parts of the tool "live" and shock the
operator.
• Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to loss of control.
SERVICE
• Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is
maintained.
SPECIFIC SAFETY RULES FOR
OSCILLATING MULTI-TOOL KIT
WARNING: Know your oscillating tool. Do not plug the tool into the power
source until you have read and understand this Instruction Manual. Learn the tool’s
applications and limitations, as well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
Always wear eye protection. Any power tool can throw foreign objects
into your eyes and cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with ANSI safety standard
Z87.1. Everyday glasses have only impact resistant lenses.
They ARE NOT safety glasses.
WARNING: Glasses or goggles not in compliance with ANSI Z87.1
could cause serious injury when they break.
Always keep hands out of the path of the saw blade. Avoid awkward hand positions
where a sudden slip could cause your hand to move into the path of the saw blade.
Secure workpiece. Use clamps or a vice to hold the workpiece. It is safer than using
your hand and it frees both hands to operate the tool.
Make sure there are no nails or foreign objects in the part of the workpiece to
be cut or sanded.
To avoid injury from accidental starting, always remove the plug from the power
source before installing or removing an accessory.
Never use dull blades in the tool. They will cut slower, leave rough cuts and break
easily due to added pressure and excessive heat. They will also overload the motor
and cause premature failure of the tool.
Never use damaged or bent blades. They will be brittle and break easily possibly
causing injury to the operator.
Never touch a saw blade immediately after using the tool. The blade will be
extremely hot and will burn your hand.
Only use accessories designed for use with this tool.
SAVE THESE INSTRUCTIONS FOR REFERENCE

7
SYMBOLS
WARNING: Some of the following symbols may appear on the oscillating
tool. Study these symbols and learn their meaning. Proper interpretation of these
V Volts n
~
Three-phase alternating
current with neutral
A Amperes Read all documentation
Hz Hertz Direct current
W Watts noNo load speed
kW Kilowatts Alternating or direct current
Microfarads Class II Construction
L Litres Splash-proof construction
kg Kilograms Watertight construction
H Hours Protective grounding at
terminal, Class I tools
N/cm² Newtons per
square centimetre .../min Revolutions or
reciprocations per minute
Pa Newtons per
square centimetre Diameter
OPM Oscillation per minute 0
Min Minutes Directional Arrow
SSeconds Warning symbol
~or AC Alternating current
~
Three-phase
alternating current
This symbol designates that this tool is listed with U.S. requirements by
ETL Testing Laboratories, Inc.
UL62841-1，UL62841-2-4;
CSA C22.2#62841-1，CSA C22.2#62841-2-4
3042597
JD2480UH

1280-002
OSCILLATING MULTI-TOOL KIT
8
KNOW YOUR OSCILLATING 3A TOOL
LED Work light
Speed control
wheel
ON/OFF
switch
Tool less accessory
holder release lever
Air vents
ACCESSORIES
A
B
C
D
OSCILLATING TOOL COMPONENTS
KEY DESCRIPTION QTY
A 1
B 2” Rigid scraper blade 1
C Triangular sanding base 1
D Triangular sandpaper
60 grit
80 grit
120 grit
3
3
3
Open back
accessory holder
1-3/4" bi metal plunge blade

9
ASSEMBLY AND OPERATING
NOTE: The drawings in the assembly and operating section of this manual may
INSTALLING ACCESSORIES
All accessories are installed on this oscillating tool in a similar manner. For the
purposes of describing the accessory installation, the triangular sanding pad and
the metal cutting blade have been illustrated.
DANGER: Always remove the plug from the power source before installing
or removing accessories or sandpaper. Failing to remove the plug from the
power source may result in the tool accidentally being started and causing
serious injury to the operator.
1. Lift the tool less accessory holder release lever (4) up and toward the front of the
tool as far as it will go (5) (Fig. 1).
NOTE: This will open the tool less blade holder (6) to accept the accessory.
2. Insert the accessory mount (7) into the opened accessory holder.
3. Align the accessory mounting slots and holes with the accessory mounting teeth
(8) in the accessory mount.
NOTE: The slots and holes in the accessory must be engaged with the matching
teeth on the accessory holder to allow the accessory to be secured within the
accessory holder.
4 Move the tool-less accessory release lever back to its original position (4) to
clamp the accessory into the accessory holder.
NOTE: Check to make sure the accessory mounting pins are still aligned with the
slots and holes in the accessory mount.
5
4
6
8
7
Fig. 1

1280-002
OSCILLATING MULTI-TOOL KIT
10
INSTALLING SANDPAPER
1. Install the hook & loop sanding pad (1) onto the tool (Fig. 2).
2. Firmly press the sandpaper (2) onto the hook & loop pad.
NOTE: Press the sandpaper firmly onto the hook & loop pad.
3. To remove the sandpaper, simply peel the sandpaper away from the
hook & loop pad (Fig. 3).
Fig. 2
Fig. 3
1
2
TURNING TOOL ON/OFF
1 To turn the tool ON, slide the ON/OFF switch (1) toward the front
of the tool (Fig. 4).
2. To turn the tool OFF, slide the ON/OFF switch toward the rear of the tool.
LED WORK LIGHT
Fig. 4
11
Fig. 5
This tool is equipped with an LED work light (Fig. 5). The work-light (1) will
automatically turn ON when the tool is plugged into the power supply. It will turn
OFF when the plug is removed from the power supply.

11
Fig. 6
1
SPEED CONTROL WHEEL
The speed of the tool can be adjusted to run the tool at speeds varying between
11,000 OPM and 21,000 OPM by rotating the speed control wheel (1) located
toward the rear of the tool housing (Fig. 8).
1. To increase the speed, rotate the speed control wheel to the right.
2. To decrease the speed, rotate the speed control wheel to the left.
NOTE: Speed #1 is the lowest speed. “MAX” is the highest speed.
The optimal speed setting will vary depending upon the type of accessory being
used, the surface being worked and the complexity of the project. For general
recommendations, see the chart under Figure 6.
Project Accessory Speed
Balsa wood Wood blade Low
Drywall Half circle blade Maximum
Restoring windows Half circle blade Medium
Door jamb Wood blade Maximum
Door casing Wood blade Med / max
Wood dowels Wood blade Maximum
Floor vent Wood blade Med / max
PVC pipe Wood blade Medium
Glued flooring Scraper Medium
Sanding Sander Med / max

1280-002
OSCILLATING MULTI-TOOL KIT
12
WARNING: For safety reasons, the operator must read the
sections of this Owner’s Manual entitled “GENERAL SAFETY
WARNINGS”, “POWER TOOL SAFETY”, “SPECIFIC SAFETY
RULES” and “ before using this oscillating tool.
Verify the following every time the oscillating tool is used:
1. Safety glasses, safety goggles, or face shield are being worn.
2. Hearing protection is being worn.
3. The blade or sandpaper is in good condition.
The accessory is properly tightened onto the accessory
holder of the tool. Failure to observe these safety rules will
significantly increase the risk of injury.
FLUSH CUTTING A DOOR JAMB AND CASING
FOR INSTALLING FLOORING
The oscillating tool can be used to flush cut a door jamb and casing to allow space
for the new flooring to fit neatly under the door jamb and casing. For the purpose of
demonstrating the procedure, floor tile is being used.
1. Install the end cutting saw blade for wood in the tool.
NOTE: The blade should be centered on the tool housing and NOT installed in the
90° position.
2. Place a scrap piece of floor tile (1) on the floor about 1/2" (12.5 mm) from the
door jamb (2) (Fig. 7).
Fig. 7
2
1
3
4
NOTE: Make sure the “good” side of the tile is facing upward to provide a smooth
surface for the blade to follow.
3. Place the tool with the saw blade (3) lightly touching the surface of the tile and
the cutting teeth NOT touching the surface to be cut.
4. Set the speed to the fastest speed.
5. Turn the tool ON

13
6. When the tool reaches its maximum set speed, carefully plunge the blade into
the door jamb while sliding the blade along the floor tile.
NOTE: Hold the tool tightly and do not put too much forward pressure on the saw
blade when cutting, as this will cause the tool to vibrate excessively.
7. Continue to make several plunge cuts until the bottom of the door jamb and
Follow the same basic procedure for installing carpet, using a thicker spacer that is
the same thickness of the carpet being installed.
CUTTING A HOLE IN WOOD FLOORING TO INSTALL A HEATING VENT
The oscillating tool can be used to cut a hole in wood flooring for installing
a heating vent.
1. Install the plunge cutting saw blade for wood in the tool.
NOTE: The blade should be centered on the tool housing and NOT installed
in the 90° position.
2. Place the floor vent on the floor and use a soft lead pencil to trace the
required rectangular hole (1) on the flooring.
3. Place the saw blade (2) near the floor surface in the middle of
one of the cutting lines.
4. Set the tool speed at a medium speed.
5. Turn the tool ON.
NOTE: The tool and blade should be at a 45° angle to the floor to allow the corner
of the blade to plunge cut into the flooring.
6. While holding the tool tightly, slowly plunge the corner of the blade into the
flooring until it cuts through the flooring. Once the plunge cut is complete, set
the tool to its highest speed and complete the cut to the corner of the rectangle.
7. Turn the saw OFF, remove it from the cut and proceed to cut in the opposite
direction to complete the cut for the first side of the rectangle.
8. Repeat steps #4, #5 & #6 to cut the remaining three sides of the rectangle.
9. When all cuts are complete, use a flat blade screwdriver to carefully pry
the cut- out from the floor.
NOTE: Do NOT use the saw blade to pry the cut-out from the floor. You will break
the blade. If the cut-out is not easy to pry from the floor, check to make sure each
line is cut completely into the corner of the rectangle.

1280-002
OSCILLATING MULTI-TOOL KIT
14
Fig. 8
1
2Fig. 9
INSTALLING AN ELECTRICAL OUTLET BOX
The oscillating tool can be used to cut a hole in drywall for installing
an electrical outlet box.
1. Install the half circle saw blade for wood & drywall in the tool.
NOTE: The blade should be centered on the tool housing and NOT installed
in the 90° position.
2. Place the outlet box on the drywall and use a soft lead pencil to trace
the required rectangular hole (1) on the drywall (Fig. 9)
3. Place the corner edge of the saw blade (2) near the drywall in the middle
of one of the cutting lines.
4. Set the speed to the highest speed.
5. Turn the tool ON.
6. When the tool reaches its maximum speed, carefully plunge the blade into
the drywall until it cuts through the drywall. Complete the cut to the corner
of the rectangle.
NOTE: Hold the tool tightly and do not put too much pressure on the saw blade
when cutting.

15
7. Turn the saw OFF, remove it from the cut and proceed to cut in the opposite
direction to complete the cut for the first side of the rectangle.
8. Repeat steps #4, #5 & #6 to cut the remaining three sides of the rectangle.
9. When all cuts are complete, use a flat blade screwdriver to carefully pry the
cut-out from the drywall.
NOTE: Do NOT use the saw blade to pry the cut-out from the drywall. You will break
the blade. If the cut-out is not easy to pry from the drywall, check to make sure each
line is cut completely into the corner of the rectangle.
USING THE DETAIL SANDER ATTACHMENT
1. Install the sanding pad on the oscillating tool.
2. Install the sandpaper on the sanding pad.
3. Set the speed control wheel between #5 and MAX.
4. Turn the switch ON.
This tool is designed for detail sanding on small surface areas. Place the sandpaper
surface of the sanding pad on the workpiece to be sanded. Keep the tool moving to
avoid gouging the surface. Use coarse sandpaper and lower speeds when sanding
rough surfaces and for removing previous finishes. Use fine sandpaper and higher
speeds to produce the smoothest surface.
USING THE SCRAPER BLADE
1. Install the scraper blade on the oscillating tool.
2. Set the speed control wheel to #4.
3. Turn the switch ON.
When using the scraper blade to scrape old finishes or glue from a workpiece, place
the underside of the blade flat on the workpiece surface and then lift upward on
the rear of the tool to allow the blade to form a very slight angle with the workpiece
surface. Feed the blade slowly into the material that is to be removed.
Do not force the tool as slower travel speeds will produce better cutting action and
reduce the risk of gouging the workpiece.
When using the scraper blade to cut carpet, place a scrap workpiece under the
carpet where the cut is being made. Set the speed to #6, turn the tool so the scraper
blade is at right angles (perpendicular) to the carpet and then feed the blade into
the carpet.

1280-002
OSCILLATING MULTI-TOOL KIT
16
MAINTENANCE
GENERAL
WARNING: When servicing, use only identical replacement parts.
The use of any other part may create a hazard or cause product damage.
DO NOT use solvents when cleaning plastic parts. Plastics are susceptible to
damage from various types of commercial solvents and may be damaged by
their use. Use a clean cloth to remove dirt, dust, oil, grease etc.
WARNING: Do not allow brake fluids, gasoline, petroleum-based products,
penetrating oils, etc. to come into contact with plastic parts. They contain
chemicals that can damage, weaken or destroy plastic.
DO NOT abuse power tools. Abusive practices can damage the tool
and the workpiece.
WARNING: DO NOT attempt to modify tools or create accessories. Any
such alteration or modification is misuse and could result in a hazardous
condition leading to possible serious injury. It will also void the warranty.
LUBRICATION
lubricant for the life of the unit under normal conditions. Therefore, no further
lubrication is required.
REPLACING THE CARBON MOTOR BRUSHES
The carbon motor brushes will wear down and require replacing. The time intervals
between replacements will vary depending upon the torques being achieved and the
hours of use. It is recommended that the brushes be checked after each 10 hours
of use. When the length of the carbon brush reaches 1/4" (6.35 mm), the brushes
should be replaced.
WARNING: Make sure the oscillating tool is unplugged from the power source.
Removing worn motor brushes
1. Remove any accessory that has been installed on the tool.
2. Lay the tool on its left side on a towel or on corrugated (Fig. 10).
3. Remove 5 screws (1) from the right-hand side of the handle (2) using
a #2 screwdriver.
Fig. 10 1
3
2

17
NOTE: The two screws at the rear of the handle (3) are shorter than the other three.
These must be replaced in the same position when replacing the handle screws.
4.
NOTE: Make sure you note the positioning of the speed control wheel and
all the wires. They must be placed in exactly the same position when
reassembling the handle.
5. Use a small slot screwdriver to lift the end of the coil spring (4) upward and
place it on top of the spade connector (5) (Fig. 11).
6. Use small needle nose pliers to pull the braided wire spade connector (6)
from the spade terminal (7).
7. Carefully grasp the braided copper brush wire (8) and lift the carbon brush (9)
from the brush holder (10).
Fig. 11 410
8
67 9
5
INSTALLING NEW MOTOR BRUSHES
8. Once the old carbon brush has been removed, use a SOFT DRY brush
to carefully remove all cutting dust from the brush holder and install the
new carbon brush in the reverse order that was used to remove the
worn carbon brush.
9. Reinstall the new carbon brush in reverse order of paragraphs 5, 6 & 7.
NOTES:
a) Make sure the braided brush wire is routed EXACTLY the same as the original.
b) Make sure the end of the coil spring is placed on top of the carbon
brush (Fig. 11).
10.Replace the right-hand half of the handle.
NOTES:
a) Make sure the speed control wheel and all wires are placed in exactly
the same position as they were when the right-hand handle was removed.

1280-002
OSCILLATING MULTI-TOOL KIT
18
b) Do NOT replace the handle screws until the second motor brush
has been replaced.
11. Grasp the reassembled handle and turn the tool onto its right side and remove
the left half of the handle.
12.Remove and replace the second carbon motor brush using the same procedures
noted above.
13.Once the second motor brush has been replaced, reposition the left half of the
handle, making sure the speed control wheel and all wires are placed in exactly
the same position as they were when the left half of the handle was removed.
14.Replace the left half of the handle, making sure it fits properly and that all six
screws are fully tightened in place.
NOTE: Make sure the two shorter screws are installed in the rear of the handle
where the power cord enters the handle.

19
EXPLODED VIEW