Berkeley Varitronics Systems OCTOPUS User manual

Quick User Guide
TM
OCTOPUS
(outside U.S. & Canada) [phone]
www.bvsystems.com
[e-mail]
Before You Start - Unpack and completely charge up your Octopus using the supplied power transformer and
charging dock. Be sure that the unit is seated rmly in the charging dock so that the metal contacts on the bottom are
connecting for a constant charge. The mini-USB port loctated on the side is only for rmware updates via any Windows
PC. Check with BVS support to make sure you have the latest rmware and updating instructions. Be sure to only use the
provided multiband antenna or other antenna authorized by BVS support. This will ensure that your unit properly scans
all bands, carriers and frequencies at maximum sensitivity.
Starting Up - Power up Octopus by pressing the white button below the touchscreen. This same button is the only
physical button on the unit and also powers down the unit by holding it in for a few seconds. Before powering up, con-
nect the antenna. This ensures that the unit will immediately begin scanning all nearby base stations, even if you do not
see those base stations listed. After about 10 seconds of a startup screen, Octopus will display the main screen of carrier
choices while continuing to scan for all nearby signals. Choose your carrier of choice, all 3G or all 4G. Depending upon
your choice and amount of nearby base stations, the list of base stations will usually take about 30 seconds to complete.
Three small dots appear in the lower right corner of the screen indicating that scanning is still in progress. You may also
go to the settings menu at any time to adjust the vibrating and audible alerts as well as check your current rmware and
unit serial number. See other page of this user guide for all screens and their paths.
Scanning and Sorting - Once Octopus has nished completely scanning, you may sort all signals by either fre-
quency, carrier or signal strength. Note: 3G signal strength is measured in RSSI while 4G signal strength is measured in
RSRP. Simply push the CARRIER, FREQ or RSRP/RSSI buttons at the top of the list to instantly sort. If Octopus identies
more than 5 unique base stations, a PAGE DOWN button appears for additonal pages of base stations to search through.
Choosing Your Base Station - Once you have located the base station of interest, touch it to take you to the
active measurement screen. From this screen you can view signal strength more accurately as you move around. A thin
watermark line around the vertical signal strength bar indicates peak measurement observed during the entire session.
Touch this at any time to reset this watermark back to the current dBm measurement. Once you have completed mea-
surements in this screen, you can continue on to align your cell booster antenna by touching the DF ANT ALIGN button.
Antenna Alignment - Now that you have a particular base station in mind, you may connect directly to your
mounted (or soon to be mounted) antenna xture. After selecting DF ANT ALIGN, you will see a reminder screen for
approximately 10 seconds. This screen is reminder to disconnect the small antenna from your unit and directly connect
the cable running from the larger permanent antenna. The reminder screen will automatically go back to the active
measurement screen allowing you to begin alignment. Begin with broad sweeps and then turn your antenna slower to
ne tune adjustment so that it is pointing directly to the base station you want off in the distance. Once your signal
strength is at maximum, install and tighten your permanent antenna and connect it directly to your cell booster. You can
now move on to scan more base stations and install more cell boosters if needed.

SORT BY FREQUENCY
SORT BY RSRP (4G) SORT BY RSSI (3G)
DIRECT MEASUREMENT
OF AT&T 3G UMTS BASE
STATION IN RSSI
SORT BY CARRIER NAME
REMINDER SCREEN FOR CONNECTING MOUNTED CELL BOOSTER ANTENNA DIRECTLY TO UNIT
DIRECT MEASUREMENT OF AT&T 4G LTE BASE STATION IN RSRP
CHOOSE CARRIER DIRECTLY OR ALL 4G OR ALL 3G UMTS BASE STATIONS. UNIT SCANS ALL 4G IN BACKGROUND BY DEFAULT
ACCESS SETTINGS MENU AT ANYTIME TO ADJUST ALERTS