VADDIO ConferenceSHOT AV User manual

Using the ConferenceSHOT AV Conferencing System
Customize this document to create a guide that's specific to your ConferenceSHOT AV installation.
A Quick Look at the System
This section covers the physical features of the system.
Front of the Camera and Speaker
Camera and zoom lens – The ConferenceSHOT AV camera features a 10X optical zoom lens (11X in Super-Wide
mode).
IR sensor – Receives signals from the IR remote. Make sure there's nothing directly in front of the camera base,
and point the remote at the camera.
Status light – The multi-colored LED indicates the camera's current state. This light can be turned off in the
administrative web interface.
Note
By default, the camera's status indicator light is active during normal operation; however, it can be
configured to remain off when the camera is powered up. The camera may be sending video even if
the light is off.
Speaker – Far-end conference audio for small rooms. Available in some ConferenceSHOT AV bundles or
separately.
Document 411-0001-40 Rev A, August 2020

Using the Remote Control
The remote provides basic camera control. Some additional functionality is available from the non-
administrative web interface.
What do you need to do? Button(s)
Power on or standby Power (green button at top right)
Select the camera to control (if
this remote controls more than
one)
Camera Select buttons 1 through 3
(second row on the remote)
Discover the camera's IP address Data Screen button (top left) – press and
hold for 3 seconds
Move the camera Arrow buttons and Home button (dark
red)
Move the camera to a preset
position
Position Preset buttons 1 through 6
(bottom two rows)
Focus the camera Auto Focus button (near arrow buttons)
Manual Focus buttons Near and Far
(below Zoom Speed buttons)
Mute the microphone(s) Mic Mute button (center)
Change the speaker volume Volume buttons (center left)
Change zoom Zoom buttons – T(telephoto) to zoom in
and W(wide-angle) to zoom out. (center
right)
Adjust for excess light behind the
camera's subject
Back Light button (top center)
Correct a motor calibration fault
condition (blinking yellow light)
Pan-Tilt Reset button (center right, beside
arrow buttons)
Storing a Preset Using the Remote
Set up the shot using the pan, tilt, and zoom controls. Then hold down the Preset button and press one of the
numbered preset buttons.
Clearing a Preset Using the Remote
Press and hold the Reset button while pressing the preset number you want to clear.
2

Operating the Camera from the Web Interface
The web interface is available on the Vaddio Device Controller touch panel (if your installation uses one) or from
a computer’s web browser.
The operator's Camera page provides most of the same controls as the IR Remote Commander, along with some
that are not available from the remote:
nPan, tilt, zoom, or return to home position
nStop or resume transmitting live camera video (video mute)
nMute or unmute the microphone(s)
nChange the speaker volume
nPut the camera in standby or bring it back to the ready state
nMove to camera presets, if any have been stored
If your installation does not include a Vaddio Device Controller or other control surface, contact the system
administrator to find out how to access the web interface.
Stopping or Resuming Video
Use the video mute button to temporarily stop video from the camera without placing it in standby. Remember
that the mute button does not mute the room's microphones. In video mute mode, the camera transmits blue
or black video, with a message that the video is muted.
3

Managing the Camera Ready State
Use the Standby button to switch between low-power (standby) and ready states.
In standby mode, the screen presents the message “Device is in standby.” On entering standby mode, the
camera pans 90° from center and 30° downward.
Muting Your Microphones
Use the audio mute button at the top of the web interface.
Adjusting Speaker and Microphone Volume
Use the Line Out slider or the + and - buttons to set the speaker volume.
Use the USB Record slider or the + and - buttons to set the microphone volume.
Note
For best performance with most computers, we recommend setting the USB Record volume high. If it
is set too low, the people at the far end of the conference may have trouble hearing you.
4

Moving the Camera
Use the arrow buttons for camera pan and tilt.The center button moves the camera to the home position.
Zooming In or Out
Use the Zoom + button to zoom in and the Zoom– button to zoom out.
Moving the Camera to a Preset Position
Use the Preset buttons (if available)to move the camera to any of its programmed positions. Presets are only
available if they have been set in the administrative interface.
5

Vaddio is a brand of Legrand AV Inc.· www.legrandav.com · Phone [phone] · Fax
+1.763.971.4464 · Email [e-mail]·
©2020 Legrand AV Inc.
Legrand AV Inc. grants permission to customers and end users to incorporate the content of this document into
their own branded guides for using the equipment described herein. For other uses, please contact Legrand AV
Inc. at [e-mail].
Vaddio is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification
purposes and are trademarks of their respective owners. All patents are protected under existing designations.
Other patents pending.
6