Berker 1640 Series User manual

Page 1/5 05-2014
Relay switch for hotel card
1640 .., 1641 ..
Operating and assembly instructions
Safety instructions
Electrical equipment may only be installed and assembled by a qualied electrician in ac-
cordance with the relevant installation standards, guidelines, regulations, directives,
safety and accident prevention regulations of the country.
Hazard due to electric shock. Disconnect before working on the device. Take into ac-
count all circuit breakers that supply dangerous voltages to the device.
Failure to comply with these instructions may result in damage to the device, re, or oth-
er hazards.
Design and layout of the device
(1)
(2)
(3)
(4)
(5)
(7)
(6)
Figure 1
(1) Insert
(2) Frame (not within scope of delivery)
(3) Fixing element
(4) Hotel card receptacle
(5) Design cover
(6) Fastening screws
(7) Potentiometer for delay time
Function
Correct use
–Centralised switching of electrical loads by insertion of a hotel card
–Storage of the hotel card
–Only suitable for use in indoor areas with no drip and no spray water
–Installation into wall box according to DIN 49073
Relay switch for hotel card
6LE000660A

Page 2/5 05-2014
Product characteristics
–Delay time of integrated relay adjustable
–Built-in LED as orientation light
–Dismantling protection
–Potential-free relay contact
Operation
Switch loads on/off
The device is ready for operation. LED in hotel card receptacle lights up.
Figure 2
Insert hotel card into the receptacle (Figure 2).
The LED goes out, connected electrical loads are switched on.
or:
Pull hotel card out of receptacle.
The LED lights up, connected electrical loads are switched off after the preset delay time.
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts can result in an electric shock.
An electric shock can be lethal.
Disconnect the connecting cables before working on the device and cover all
live parts in the area!
ç
Relay switch for hotel card
6LE000660A

Page 3/5 05-2014
Connect device and mount centre plate
L1 ... L3 Outer conductor
NNeutral conductor
LN
L
N
Figure 3
L L1 L2 L3
N
LN
L3
N
L1
L2
Figure 4
Connect relay switch insert (1) according to connection diagram (Figure 3/4).
Observe permissible connected load. If necessary use load connector (Figure 4).
Install insert (1) into wall box, connecting terminals must be at the bottom.
Fit frame (2) and screw to xing element (3).
Fit hotel card receptacle (4) and fasten with screws.
If necessary set delay time.
Snap design cover (5) onto hotel card receptacle.
Relay switch for hotel card
6LE000660A

Page 4/5 05-2014
Dismantle design and set delay time
3 mm
Figure 5
Remove design cover. To do this, enter slot screwdriver into the opening of the hotel card
receptacle (Figure 5) and loose and remove design cover by careful repeated levering on
the left and on the right hand side .
Run slot screwdriver through recess of the hotel card receptacle and set delay time by turn-
ing the potentiometer (7).
Observe labelling of potentiometer:
Stop left 0 s, stop right 60 s.
Appendix
Technical Data
Rated voltage AC 230 V~
Rated frequency 50/60 Hz
Switching voltage AC 230 V~
AC/DC 12 ... 48 V
Switching current at AC 230 V~:
- ohmic load max. 10 A AC1
- motors at cosφ 0.6 max. 6 A
Switching current at AC/DC 12 V min. 100 mA
max. 8 A
Switching capacity 230 V~:
- 230 V incandescent and halogen lamps 1500 W
- conventional transformers 1500 VA
- electronic transformers 1500 W
- uorescent lamps 1500 VA
- compact uorescent lamps 200 W
- dimmable 230 V retrot LED lamps 200 W
Relay switch for hotel card
6LE000660A

Page 5/5 05-2014
Contact type relay, 1 s, potential-free
Adjustable delay time 0 s, 15 s, 30 s, 60 s
Dimensions hotel card max.
- width 50 ... 55 mm
- thickness 0.8 ... 1.2 mm
Operating temperature -5 ... +50 °C
Storage temperature -25 ... +70 °C
Degree of protection IP20
Protection class II
(for complete installation)
Connections screw terminals
- single stranded 0.5 ... 2.5 mm²
- nely-stranded with conductor sleeve 0.5 ... 2.5 mm²
Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
Our products are under guarantee within the scope of the statutory provisions.
If you have a warranty claim, please contact the point of sale or ship the device postage free
with a description of the fault to the appropriate regional representative.
Address of manufacturer
Berker GmbH & Co. KG
Klagebach 38
58579 Schalksmühle/Germany
Phone: + 49 (0) 23 55/90 5-0
Fax: + 49 (0) 23 55/90 5-3111
berker.com
Relay switch for hotel card
6LE000660A