Best Fitness BFFT10R User manual

BFFT10R
OWNER’S MANUAL
v. 051216

2
WARNING LABELS
WARNING:
WARNING:
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
CallÊ1-800-556-3113
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT.
TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
Inspect equipment before each workout. Check that all nuts, bolts, screws and pop pins
are in place and fully tightened. Also, before use, check cables for sign of wear. Replace all
worn parts immediately. Never use machine if any parts are damaged or missing.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
Keep clear of the cables and all moving parts when machine is in use.
Always make sure all Snap Links are closed when doing cable/pulley/strap exercises.
Exercise with care. Perform your exercises at a smooth moderate pace; never perform jerky
or uncoordinated movements that may cause injury.
It is recommended that you workout with a training partner.
Do not allow children or minors to play on or around this equipment.
If unsure of proper use of equipment, call your local Best Fitness distributor or the Best
Fitness customer service center at 1-800-556-3113.
WARNING: Consult your physician before starting your exercise program. For your own
safety, do not begin any exercise program without proper instruction.
WARNING:
WARNING:
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
WARNING!
SafetyÊandÊMaintenance
ofÊCables
IMPORTANT:ÊCables are
wear items. It is your
responsibility to prevent
unexpected breakage.
Cable inspection
should be performed
daily.
Inspect all cables, the
nylon coating on all
cables, and the area near
fitting at each end of
each cable.
Replace and damaged
or worn cable
immediately.
Do not allow the
machine to be used until
damaged or worn cables
are replaced. Using or
allowing a machine to be
used with a suspect
cable can result in
serious injury. See
Owner’s Manual for more
information.
For Best Fitness Customer Service
CallÊ1-800-556-3113
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
CallÊ1-800-556-3113
WARNING:
WARNING:
WARNING:
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
SafetyÊandÊMaintenance
ofÊCables
Ê
CallÊ1-800-556-3113
MAINTENANCE
SCHEDULE
Check the function and integrity
of the following components.
As noted, inspect equipment
before each workout. Replace
all damaged, broken or worn
components immediately.
Cables: Check tension, end
fittings, and coating
Check that locking nut
at weight stack is tight
Upholstery: Wipe down and dry
Clean and condition
Frame: Wipe down and dry
Polish / Wax
Chrome: Wipe down and dry
Polish / Lubricate
Nut / Bolts / Fasteners: Tighten
and / or adjust as needed
Guide Rods: Lubricate and clean
Linear Rods: Lubricate and clean
Seat Sleeves: Lubricate and clean
Weight Stack Pins
Warning Instruction Labels
Springs / Pop Pins
Anti Skid Surfaces
Hand Grips / Rollers
CallÊ1-800-556-3113
Adjustments / Locking Pins /
Tightening Knobs
WARNING:

3
TABLE OF CONTENTS
SAFETY INSTRUCTIONS..............................
PREPARATION...........................................
HARDWARE LIST.......................................
HARDWARE ILLUSTRATION........................
PART LIST / ILLUSTRATION.......................
ASSEMBLY INSTRUCTIONS.........................
EXPLODED VIEW.......................................
CONTACT PAGE.........................................
PAGE 4
PAGE 5
PAGE 6
PAGE 8
PAGE 10
PAGE 12
PAGE 28
PAGE 30

4
Unpacking the Equipment
The BFFT10R is carefully tested and inspected before
shipment. We have shipped the unit in two boxes
that require assembly. Ask for assistance during the
assembly process.
Carefully unpack the boxes and lay the pieces on
the oor near the area where you plan to use the
equipment.
IMPORTANT SAFETY INSTRUCTIONS
When using exercise equipment, you
should always take basic precautions,
including the following:
• Read all instructions before using the BFFT10R. These
instructions are written to ensure your safety and to
protect the unit.
• Do not remove any safety labels fromt the
machine.
• Do not allow children on or near the equipment.
• Use the equipment only for its intended purpose as
described in this guide. Do not use accessory
attachments that are not recommended by the
manufacturer. Such attachments might cause injuries.
• Wear proper exercise clothing and shoes for your
workout, no loose clothing.
• Keep hands, limbs, loose clothing, and long hair well
out of the way of all moving parts.
• Use care when getting on or o󰀨 the unit.
• Do not overexert yourself or work to exhaustion.
• If you feel any pain or abnormal symptoms, stop your
workout immediately and consult your physician.
• Never operate unit when it has been dropped or
damaged. Return the equipment to a service center
for examination and repair.
• Never drop or insert objects into any opening in the
equipment.
• Always check the unit before each use. Make sure
that all fasteners are secure and in good working
condition.
• Do not use the equipment outdoors or near water.
Personal Safety During Assembly
• It is strongly recommended that a qualied dealer
assemble the equipment. Assistance is required.
• Before beginning assembly, please take the time to
read the instructions thoroughly.
• Read each step in the assembly instructions and
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have to
disassemble components and that you may have
damaged the equipment.
• Assemble and operate the BFFT10R on a solid, level
surface. Locate the unit a few feet from the walls or
furniture to provide easy access.
The BFFT10R is designed for your enjoyment. By
following these precautions and using common
sense, you will have many safe and pleasurable hours
of healthful exercise with your Best Fitness BFFT10R.
After assembly, you should check all functions to
ensure correct operation. If you experience problems,
rst recheck the assembly instructions to locate any
possible errors made during assembly. If you are unable
to correct the problem, call the dealer from whom
you purchased the machine or call 1-800-556-3113
for the dealer nearest you.
Obtaining Service
Please use this Owner’s Manual to make sure that all
parts have been included in your shipment. When
ordering parts, you must use the part number and
description from this Owner’s Manual. Use only
Best Fitness replacement parts when servicing this
machine. Failure to do so will void your warranty and
could result in personal injury.
For information about product operation or service,
go to www.besttness.com or contact an authorized
Best Fitness dealer or a Best Fitness factory-authorized
service company or contact Best Fitness customer
service at one of the following:
Toll Free: 1-800-556-3113
Phone: [phone]
Fax: [phone]
Hours: M-F 8:30-5:00 CST
E-Mail: [e-mail]
Or write to: Best Fitness
Service Department
1900 S. Des Plaines Ave.
Forest Park, IL 60130 USA
Retain this Owner’s Manual for future
reference. Part numbers are required when
ordering parts.

5
PREPARATION
Assembly Tips
Read all “Notes” on each page before beginning each
step.
While you may be able to assemble the BFFT10R using
the
illustrations only, important safety notes and other tips are
included in the text.
Some pieces may have extra holes that you will not use.
Use only those holes indicated in the instructions and
illustrations.
NOTE: With so many assembled parts, proper alignment
and adjustment is critical. While tightening the
nuts and bolts, be sure to leave room for
adjustments.
NOTE: The bottles that are marked “Poison” is your
touch up pain. Keep away from children.
CAUTION: Obtain assistance! If you feel like you can’t
assemble the BFFT10R by yourself then do not attempt
to do so as this could result in injury. Review installation
requirements before proceeding with the following steps.
Required Tools
The basic tools that you must obtain before assembling the
BFFT10R include but are not limit to:
• Metric Wrench Set
• Adjustable Wrench
• Metric Allen Key Set
• Screwdriver (Standard/Phillips)\
Installation Requirements
Follow the installation requirements when assembling the
BFFT10R.
Set up the BFFT10R on a solid, at surface. A smooth at
surface under the machine helps keep it level.
Provide ample space around the machine. Open space
around the machine will allow for easier access.
For aesthetic purposes, insert all bolts in the same
direction unless specied (in text or illustrations) to do so
otherwise.
Leave room for adjustements. Tighten fasteners such as
bolts, nuts, and screws so the unit is stable, but leave
somewhat loose for adjustments. Do not fully tighten
fasteners until instructed in the assembly steps to do so.
Fill out and mail the warranty card.
Ordering Replacement Parts
If you need to order replacement parts please be prepared
to provide the following information when contacting us so
that we can assist you better.
1. Model Number
2. Place of Purchase
3. Serial Number (S/N)
4. Part# and Description YOUR S/N # CAN
BE FOUND HERE




PART# SIZE DESCRIPTION QUANTITY
Part numbers are required when ordering parts.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
25X12.5X10mm
25X10.5X32mm
7350mm
6740mm
90mm
45X45mm
40X80mm
25mm
56X96mm
86X45mm
PULL PIN
BUSHING
BUSHING
CABLE
CABLE
STEEL CHAIN
SNAP LINK
PULLEY
PLASTIC PLATE
SQUARE END CAP
OVAL END CAP
END CAP
SILICON NUBE
EVA PAD
EVA PAD
RUBBER
HANDLE STRAP
2 PCS.
4 PCS.
8 PCS.
1 PCS.
2 PCS.
2 PCS.
4 PCS.
25 PCS.
1 PCS.
2 PCS.
2 PCS.
1 PCS.
16 PCS.
2 PCS.
2 PCS.
2 PCS.
2 PCS.
11
HARDWARE LIST
6

PART# SIZE DESCRIPTION QUANTITY
Part numbers are required when ordering parts.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
HARDWARE LIST
7
M12X175mm
M10X42mm
M10X62mm
M10X72mm
M10X102mm
M6X8mm
M8X10mm
M6
M12
M10
M12
M10
M12
38X12X2mm
HEX HEAD BOLT
HEX HEAD BOLT
HEX HEAD BOLT
HEX HEAD BOLT
HEX HEAD BOLT
SOCKET SCREW
ACORN CAPNUT
WASHER
WASHER
NYLON LOCK NUT
NYLON LOCK NUT
TOP STACK
BOTTOM STACK
WEIGHT PLATE PIN
PUSHNUT
PIVOT AXLE
NUT
WASHER
CLEVIS PIN
RETAINING RING
2 PCS.
21 PCS.
16 PCS.
4 PCS.
4 PCS.
3 PCS.
6 PCS.
2 PCS.
4 PCS.
90 PCS.
2 PCS.
45 PCS.
1 PCS.
12 PCS.
1 PCS.
1 PCS.
1 PCS.
1 PCS.
1 PCS.
2 PCS.
2 PCS.

8
HARDWARE ILLUSTRATION
PART 18 - M12X175mm Hex Head Bolt, 2 PCS.
PART 19 - M10X42mm Hex Head Bolt, 21 PCS.
PART 20 - M10X62mm Hex Head Bolt, 16 PCS.
PART 21 - M10X72mm Hex Head Bolt, 4 PCS.
PART 22 - M10X102mm Hex Head Bolt, 4 PCS.
PART 23 - M6X8mm Screw, 3 PCS - Reserve for future usage.
PART 26 - M12 Washer, 4 PCS.
HARDWARE(shown in actual size)
mminch

9
HARDWARE ILLUSTRATION
PART 27 - M10 Washer, 90 PCS.
PART 28 - M12 Nylon Lock Nut, 2 PCS.
PART 29 - M10 Nylon Lock Nut, 45 PCS.
PART 33 - Push Nut, 1 PCS.
PART 34 - Pivot Axle, 1 PCS.
PART 35 - M12 Nut, 1 PCS. PART 36 - M12 Large Washer, 1 PCS.
HARDWARE(shown in actual size)
mminch

10
PART LIST
PART A - LEFT LOWER BEAM, 1 PCS.
PART B - RIGHT LOWER BEAM, 1 PCS.
PART C - BASE FRAME, 1 PCS.
PART D - SELECTING UPRIGHT, 2 PCS.
PART E - LEFT UPRIGHT, 1 PCS.
PART F - RIGHT UPRIGHT, 1 PCS.
PART G - SUPPORT BEAM, 1 PCS.
←E
←F

11
PART LIST
PART H - LAT BAR, 1 PCS.
PART I - GUIDE ROD, 2 PCS.
PART J - HANDLE ASSEMBLY, 2 PCS.
PART K - DOUBLE PULLEY, 2 PCS.
PART L - PULLEY HOLDER, 2 PCS.
PART M - SINGLE PULLEY, 1 PCS.
PART N - SELECTOR ROD, 1 PCS.

12
Be careful to assemble all components
in the sequence they are presented.
1A. Attach Left Lower Beam (A) to Base Frame (C) using:
2 - (#20) M10X62mm Hex Head Bolt
4 - (#27) M10 Washer
2 - (#29) M10 Nylon Lock Nut
1B. Attach Right Lower Beam (B) to Base Frame (C)
using:
2 - (#20) M10X62mm Hex Head Bolt
4 - (#27) M10 Washer
2 - (#29) M10 Nylon Lock Nut
Note: Bolt #20, M10X62mm, in this step needs to be bottom up as
shown in the picture to the right.
STEP
1
NOTE:
Finger tighten all hardware first in this step. Wrench tighten bolts at
the end of this step, some components may be pre-assembled.
Nylon lock nuts will not fully screw onto bolts, must wrench tighten.

13
STEP
1

Be careful to assemble all components
in the sequence they are presented.
STEP
2
14
2A. Attach a Selecting Upright (D) to Left Lower Beam (A) using:
2 - (#20) M10X62mm Hex Head Bolt
4 - (#27) M10 Washer
2 - (#29) M10 Nylon Lock Nut
2B. Attach a Selecting Upright (D) to Right Lower Beam (B)
using:
2 - (#20) M10X62mm Hex Head Bolt
4 - (#27) M10 Washer
2 - (#29) M10 Nylon Lock Nut
2C. Slide a Handle Assembly (J) onto each Selecting
Upright (D).
2D. Secure Left Upright (E) onto left Selecting Upright (D) and
secure Right Upright (F) onto right Selecting Upright (D) using:
4 - (#21) M10X72mm Hex Head Bolt
8 - (#27) M10 Washer
4 - (#29) M10 Nylon Lock Nut
2E. Attach Left Upright (E) to Left Lower Beam (A) and
attach Right Upright (F) to Right Lower Beam (B) using:
2 - (#20) M10X62mm Hex Head Bolt
6 - (#27) M10 Washer
2 - (#29) M10 Nylon Lock Nut
2F. Insert end caps into each top end opening of Left Upright (E)
and Right Upright (F) using:
2 - (#11) 40X80mm Oval End Cap
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten
until the end of Step 4, some components may be pre-assembled.
Nylon lock nuts will not fully screw onto bolts, must wrench tighten.

STEP
2
15

Be careful to assemble all components
in the sequence they are presented.
STEP
3
16
3A. Insert each Guide Rod (Y) thru one 86X45mm Eva Pad (#15)
and into a circular opening of Base Frame (C).
3B. Insert all Weight Plates (#31) onto Guide Rods (Y).
3C. Insert Push Nut (#33) onto Selector Rod (N) and secure by
sliding Pivot Axle (#34) thru the Push Nut (#33) and the rst
opening of Selector Rod (N).
3D. Take the key ring end of the Weight Plate Pin (#32) and slide
it onto the the threaded shaft of Single Pulley (M) and secure
by screwing on a M12 Nut (#35).
3E. While holding the Selector Rod, place the bottom end of
Top Stack (#30) onto the Push Nut and the Pivot Axle.
3F. Secure the Top Stack to the Selector Rod by sliding a M12
Large Washer (#36) onto the threaded shaft of Single Pulley (M)
and screwing Single Pulley (M) into the internal threads of
Selector Rod (M). Slide Top Stack onto Guide Rods (Y).
Note: Tighten the M12 Nut (#35) to better secure Single Pulley (M).
3G. Insert Each Guide Rod (Y) into a circular opening of
Support Beam (G), and attach Support Beam (G) to both Left
Upright (E) and Right Upright (F) using:
4 - (#20) M10X62mm Hex Head Bolt
8 - (#27) M10 Washer
4 - (#29) M10 Nylon Lock Nut
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten
until the end of Step 4, some components may be pre-assembled.
Nylon lock nuts will not fully screw onto bolts, must wrench tighten.

STEP
3
17

Be careful to assemble all components
in the sequence they are presented.
STEP
4
18
4A. Attach Lat Bar (H) to Left Upright (E) and Right Upright (F)
using:
4 - (#21) M10X72mm Hex Head Bolt
8 - (#27) M10 Washer
4 - (#29) M10 Nylon Lock Nut
4B. Attach a Double Pulley (K) to a Handle Assembly (J) on both
the left and right side using:
2 - (#18) M12X175mm Hex Head Bolt
4 - (#26) M12 Washer
2 - (#28) M12 Nylon Lock Nut
Note: Do not tighten down bolts to hard, make sure that the
Double Pulley is able to swivel.
NOTE:
Finger tighten all hardware first. Wrench tighten all bolts at the end
of this step, some components may be pre-assembled.
Nylon lock nuts will not fully screw onto bolts, must wrench tighten.

STEP
4
19

Be careful to assemble all components
in the sequence they are presented.
STEP
5
20
5A. Attach two Pulleys to Double Pulley (K) using:
2 - (#19) M10X42mm Hex Head Bolt
4 - (#27) M10 Washer
2 - (#8) 90mm Pulley
2 - (#29) M10 Nylon Lock Nut
5B. Attach a Pulley to Pulley Holder (L), the inside holder of Left
Upright (E), and the front holder of Left Lower Beam (A) using:
3 - (#19) M10X42mm Hex Head Bolt
6 - (#27) M10 Washer
3 - (#8) 90mm Pulley
3 - (#29) M10 Nylon Lock Nut
5C. Attach a Pulley to the front and rear top openings of Left
Upright (E) using:
2 - (#22) M10X102mm Hex Head Bolt
4 - (#27) M10 Washer
4 - (#3) 25X10.5X32mm Bushing
2 - (#8) 90mm Pulley
2 - (#29) M10 Nylon Lock Nut
5D. Cable Routing: Use a 6740mm Cable (#5). First, route the non-clip
end of the cable over pulley A1 and under then around pulley A2.
Second, route the cable up and over pulley A3 then over and down
pulley A4. Third, route the cable down and around pulley A5 then up
and over pulley A6. Lastly, route the cable down and around pulley
A7 and back up into the cable holder on Handle Assembly (J).
Secure the cable just enough to hold by tightening the socket set
screw (#24) that is pre-installed on Handle Assembly (J).
NOTE:
Finger tighten all hardware first. DO NOT wrench tighten until the
end of step 8, some components may be pre-assembled.
Nylon lock nuts will not fully screw onto bolts, must wrench tighten.