Best Fitness BFPR100 User manual

BFPR100
OWNER’S MANUAL

2
WARNING, SAFETY, & MAINTENANCE
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT.
TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
WARNING:
WARNING!
Safety and Maintenance
of Cables
IMPORTANT:
Cable inspection
should be performed
daily.
Replace and damaged
or worn cable
immediately.
                            
Call 1-800-556-3113
DO NOT REMOVE WARNING LABELS FROM MANUAL OR MACHINE

3
TABLE OF CONTENTS
SAFETY INSTRUCTIONS ............................PAGE 4
PREPARATION ............... ............................ PAGE 5
HARDWARE LIST ...... ...... ............................ PAGE 6
HARDWARE ILLUSTRATION ............................ PAGE 7
PART LIST/ILLUSTRATION ............................ PAGE 8
ASSEMBLY INSTRUCTIONS ............................ PAGE 10
EXPLODED VIEW ...... ...... ............................ PAGE 18
CONTACT PAGE ...... ...... ............................ PAGE 20
•
•
•
•
•
•
•
•

4
IMPORTANT SAFETY INSTRUCTIONS
When using exercise equipment, you
should always take basic precautions,
including the following:
Personal Safety During Assembly
Obtaining Service
Retain this Owner’s Manual for future
reference. If you need to order replacement
parts please be prepared to provide the
following information when contacting us so
that we can assist you better.
1. Model Number
2. Place of Purchase
3. Serial Number (S/N)
4. Part # and Description

5
PREPARATION
Any Questions?
Call [phone]
Required Tools
Installation Requirements
Assembly Tips

6
PFPR100 - HARDWARE LIST
PART#
1
2
3
4
Part numbers are required when ordering parts.
SIZE
M10X70mm
M10X75mm
ø11Xø30X2.5mm
M10
DESCRIPTION
HEX HEAD BOLT
HEX HEAD BOLT
FLAT WASHER
NYLON LOCK NUT
QUANTITY
12 PCS.
8 PCS.
40 PCS.
20 PCS.

7
HARDWARE ILLUSTRATION
Part #1 HEX HEAD BOLT M10X70mm QTY. 12
Part #2 HEX HEAD BOLT M10X75mm QTY. 8
Part #3 FLAT WASHER ø11Xø30X2.5mm QTY. 40
Part #4 NYLON LOCK NUT M10 QTY. 20

 



8
PART LIST/ILLUSTRATION
PART A -- FRAME A, 1 PCS
PART B -- FRAME B, 1 PCS
PART C -- FRAME C, 2 PCS
PART D -- FRAME D, 4 PCS
PART E -- FRAME E, 2 PCS
PART F -- CHIN UP BAR, 1 PCS
PART G -- LIFT OFF, 2 PCS
PART H -- SAFETY CATCH, 2 PCS
PART #5 -- FOOT CAP, 4 PCS
PART #6 -- CLIP-ON SPACER, 2 PCS
PART #7 -- END CAP, 4 PCS
PART #8 -- SAFETY PIN, 4 PCS

9
NOTE

10
STEP
1
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten until the last step.
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto
bolts, they must be wrench tighten to fully go on.
1A. Install four Foot Caps (#5) in Frame A (A) and Frame B (B).
1B. Install two Clip-On Spacers (#6) on Frame A (A) and Frame B (B).
1C. Attach Frame A (A) and Frame B (B) to Frame C (C) using:
4 - (#1) M10X70mm Hex Head Bolt
8- (#3) ø11Xø30X2.5mm Flat Washer
4- (#4) M10 Nylon Lock Nut

11
STEP
1
Above shows STEP 1 assembled and completed.

12
STEP
2
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten until the last step.
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto
bolts, they must be wrench tighten to fully go on.
2A. Attach two Frame D (D) to Frame A (A) using:
4 - (#1) M10X70mm Hex Head Bolt
8- (#3) ø11Xø30X2.5mm Flat Washer
4- (#4) M10 Nylon Lock Nut
2B. Attach two Frame D (D) to Frame B (B) using:
4 - (#1) M10X70mm Hex Head Bolt
8- (#3) ø11Xø30X2.5mm Flat Washer
4- (#4) M10 Nylon Lock Nut

13
STEP
2
Above shows STEP 2 assembled and completed.

14
STEP
3
3A. Install four End Caps (#7) in two Frame E (E).
3B. Attach one ends of two Frame E (E) and Frame C (C) to Frame D (D) using:
4 - (#2) M10X75mm Hex Head Bolt
8- (#3) ø11Xø30X2.5mm Flat Washer
4- (#4) M10 Nylon Lock Nut
3C. Attach another ends of Frame E (E) and Chin Up Bar (F) to Frame D (D)
using:
4 - (#2) M10X75mm Hex Head Bolt
8- (#3) ø11Xø30X2.5mm Flat Washer
4- (#4) M10 Nylon Lock Nut
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware first in this step. Wrench tighten ALL hardware at the
end of STEP 3C. Some components may be pre-assembled. Nylon lock nuts will not
fully screw onto bolts, they must be wrench tighten to fully go on.

15
STEP
3
Above shows STEP 3 assembled and completed.

16
STEP
4
4A. Insert Safety Catches (H) and Lift Offs (G) into desired positions.
4B. Insert the Safety Pins (#8) at the ends of the Safety Catches (H) and Lift
Offs (G).
NOTE:
Please make sure the Safety Pins (#8) are fully engaged after Safety
Catches (H) and Lift Offs (G) are inserted into the Frames.
Be careful to assemble all components
in the sequence they are presented.

17
STEP
4
Above shows STEP 4 assembled and completed.

18
EXPLODED VIEW DIAGRAM