Best Time Toys Multifunction Activity Center User manual

Multifunction Activity Center
ENG
Best Time Toys

ENG IMPORTANT Read instructions carefully and keep for future reference.
WARNING
Read these instructions carefully before use and keep them for future reference. Ensure
your child’s safety by following these instruc-tions. Follow these assembly instructions carefully.
IMPORTANT! Check this product for damage hardware, loose joints, missing parts, or sharp edges
before assembly and peri-odically during use. DO NOT use if any parts are missing, damage or
broken. Do not use replacements part or accessories other than those approved by the producer.
•Never leave the child unattended.
•The child will be able to reach further and move rapidly when in the baby walking frame.
•A child’s safety is your responsibility.
•Prevent access to stairs, steps and uneven surfaces.
•Guard all fires, heating and cooking appliances.
•Remove hot liquids, electrical flexes and other potential hazards from reach.
•Prevent collisions with glass in doors, windows and furniture.
•Do not use the baby walking frame if any components are broken or missing.
•This baby walking frame should be used only for short periods of time (e.g. 20mins).
•This baby walking frame is intended to be used by children who can sit unaided,
approximately from 6 months. It is not intended for children weighing more than 12 kg.
•Before use: Check that the baby walker is correctly assembled.
•Check regularly that: All fastenings and components are secure. Tighten and adjust as
necessary and the castors rotate and run freely. That no components are broken or missing.
•Only use replacement spare parts that are recommended or supplied by Mamas & Papas.
Non-approved spare parts may render the repair or baby walker unsafe.
•The toy should be assembled by adult.
PRODUCT CARE
Wipe all plastic/metal parts clean with a damp cloth using mild soap, dry thoroughly. Light
soiling of the seat pad can be removed with a damp cloth and a mid soap.
Do not use strong detergents or abrasive materials. Do not dry clean. Do not tumble dry.
Line dry the seat pad.
To maintain stopping performance, clean friction strips regularly with damp cloth.

BATTERY INFORMATION
•Do not mix new and used batteries.
•Do not mix different types of batteries.
•Only use replacement batteries of the type recommended.
•Recommended batteries, 2X 1.5V, ‘AA’ / SUM3 / LR6.
•Always remove exhausted batteries from the product.
•Do not attempt to charge non rechargeable batteries.
•Remove rechargeable batteries before charging.
•Charge under adult supervision.
•The batteries must be inserted with the correct polarity.
•Do not short-circuit the supply terminals.
•Remove the batteries when the product is not being played with for extended periods of time.
•For optimum performance Mamas & Papas recommend using high power, alkaline batteries,
for example Energizer or Duracell.
BATTERY DISPOSAL
Dispose of exhausted batteries at an official waste disposal site.
Do not burn or place in household waste.

PARTS
Rainbow toy x1
Butterfly toy x1 Octopus toy x1
Swing device x1
Base section x1
Top section x1
Play tray x1
Frame supporter x3
Seat pad x1
Lollipop & bee
toy bar x1
Tools required
Phillips screwdriver (cross head) For activity tray batteries only.

TO ASSEMBLING THE FRAME
1. Open frame supporters
Turn one side of frame supporter outward until you hear the frame supporter lock into
position.
( 1 ) ( 2 )
2.
Place the base section on the floor, slot the end of frame supporters into the holes indicated in
the drawing (1).
Press the button in and push the frame supporters downwards to adjust the height to your
wish position. (2) (3)
1
TO ASSEMBLING THE FRAME
(3)
(2)

FITTING THE SEAT PAD
4.To fix the seat when use as baby walker
Find the rotating lock which under the seat groove of upper tray. First press the button
(1),then push the safe lock outward (2) to rotate the seat, push the safe lock inward to lock and
fix the seat.
3.
Position the seat pad into the top section. Using moderate force push downwards
until it locks in the top section.
TO FIX THE SEAT
1
2

TO STORE THE BABY WALKER
6.
Lift the top section upwards, until three frame supporters are starded as shown in fig (3).
5.
Pull forward of safty pin at left side of each frame supporers fig (2a), and press botton (2b) at
right side of each frame supporers, then forward the frame supporters to the center of baby
walker.
Make sure all three frame supporters are forward to the center of baby walker.
OPENING THE BABY WALKER
(1)(2) (3)
b
a
(1) (2) (3)

ATTACHING THE RAINBOW TOY
8.
Place the toy tray into the holes located on the top section and turn the tabs around to secure
the toy tray to the walker.
7.
Push downward the toy rainbow press down and clockwise rotation until hear sound of
“Click” then it is in the position. 2xAA size Alkaline batteries are needed for the toy
(batteries no included). Put batteries into the toy tray. The toy should be assembled by
adult.
ATTACHING THE TOY TRAY
1
2

ATTACHING THE OCTOPUS TOY AND BUTTERFLY TOY
9.
Position the octopus toy and butterfly toy over the slots in the front tray. Insert the
tabs on the toys into the slots on the tray up and turn them in a clockwise direction
until they lock into place.
ATTACHING THE TOYS
(12.a)
10.
Insert the toys into the housing within the jupmerloo top section, paying particular attention
to the direction, as shown in.Fig(12.a) Once the toys has been inserted into the upper tray
twist to fix in to the locked position.

SWING MODEL
11.Assembly swing device
And in the bottom of the lower plate on both sides of the groove.
12. Remove the swing device
The plate on the front end at the bottom of the swing cushion.

Designed in Sweden.
Made in China for Scandinavian Kids Group AB, Box 29098, SE-100 52, Stockholm, Sweden
www.carenababy.com [email protected]
Best Time Toys