Better Homes and Gardens 9223GYWM User manual

Pg 1 of 44 [phone] IS92230-I3
Model
9223GYWM (Rustic Gray)
MCS 11/21/2019
Date:
Lot number:
Product Inquiries - Installation Help
Just call [phone] for parts and service. For faster service, have the model number
ready when calling.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
For Spanish and French instructions, start on page 23.
Para instrucciones en español y francés, comience en la página 23.
Pour les instructions espagnoles et françaises, commencez à la page 23.

Pg 2 of 44 [phone] IS92230-I3
Before You Begin:
Thank you for purchasing this product. Please identify all parts and hardware
pieces before you begin. When laying out parts, place them on a soft surface
to prevent scratching.
If any pieces are missing, call our Toll Free Number 1-800-892-3986 between
8:00AM-5:00PM EST Monday through Friday.
Cleaning Note:
Cleaning with a dry cloth may be sufficient, but for other stains or marks wipe
gently with a damp cloth.
DO NOT use strong detergents or abrasive cleaners, they may damage the
surface of this product.
It is imperative that the unit be fastened
to the wall for safety and stability.
For safety reasons, it is imperative
to use a stepladder.
Tools Needed - not included

Pg 3 of 44 [phone] IS92230-I3
A
G
H
K
E
B
F
D
C
I
J
List of Parts
Q
R
Q
M
N
P
L
O
ATop Panel 1
BAdjustable Shelf 1
CFixed Shelf 1
DMiddle Shelf 1
ETop Left Side Panel 1
FTop Right Side Panel 1
GTop Trim 1
HMagnet Block 1
IHanging Rail 1
JTop Left Trim 1
K Top Right Trim 1
LBottom Trim 1
MTop Support Rail 1
NBottom Support Rail 1
ORight Leg Assembly 1
PLeft Leg Assembly 1
QDoor 2
RBack Panel 1

Pg 4 of 44 [phone] IS92230-I3
Large Screw
Slotted Bracket
Cambolt
Dowel
Screw
(used on pasrt 6, 7, & 8)
Hinge
1
2
6
4
5
7
x 12
x 20
x 30
x 32
x 4
x 2
Cam
3x 20
Angle Block
8x 6
List of Hardware
Door Handle Screw
9x 4
Door Handle
10 x 2
Shelf Clip
11 x 4
Nail
12 x 22
Screw Cover Sticker
13 x 14
Cam Sticker
14 x 16
Magnet
15 x 1
Magnet Screw
16 x 2
Magnet Strike
17 x 2
Magnet Strike Screw
18 x 2
Long Screw
19 x 2
Foot
20 x 4
Wall Anchor
21 x 2
Mounting Screw
22 x 2
Mounting Spacers
23 x 2

Pg 5 of 44 [phone] IS92230-I3
• Insert cams (3) into the top trim (G), as shown. NOTE the direction of the cams (3).
• With the magnet (15) facing down, attach it to the magnet block (H), as shown.
•Attach the magnet block (H) to the top trim (G) as shown.
• Attach the slotted brackets (7) to the top trim (G) as shown.
• Insert cams (3) into the hanging rail (I) and the fixed shelf (C), as shown. NOTE the direction of the cams (3).
3
3
3
19
3
16
H
15
G
I
C
7
5
7
5
unfinished edge
Step 1 - Attaching the Magnet.
Step 2 - Installing Cams to the Hanging Rail and Fixed Shelf.
NOTE the direction
of the cams (3).
NOTE the direction
of the cams (3).
NOTE the direction
of the cams (3).
3x 2
5x 2
7x 2
15 x 1
16 x 2
19 x 2
3x 6

Pg 6 of 44 [phone] IS92230-I3
unfinished edge
E
F
8
5
5
2
3
8
3
2
•Insert cams (3) into the top side panels (E and F), as shown. NOTE the direction of the cams (3).
•Attach cambolts (2) to the top side panels (E and F) and angle blocks (8) to top side panels (E and F),
as shown. DO NOT OVERTIGHTEN ANGLE BLOCK SCREWS (5)!
Step 3 - Installing Angle Blocks to the Top Side Panels.
NOTE the direction
of the cams (3).
Top
5
58
8
2
2
3x 4
2x 4 5x 6
8x 6

Pg 7 of 44 [phone] IS92230-I3
K
K
5
6
5
6
unfinished edge
•Attach two hinges (6) to top right trim (K), as shown. DO NOT OVERTIGHTEN HINGE SCREWS (5)!
• Repeat for the top left trim (J).
Top
Step 4 - Installing Hinges.
J
5
Repeat for the top left trim (J).
6
5x 8
6x 4
Top
6

Pg 8 of 44 [phone] IS92230-I3
•Insert dowels (4) into the top right trim (K), as shown.
•Attach the top right side panel (F) to the top right trim (K), as shown. DO NOT OVERTIGHTEN SCREWS (5)!
• Repeat for the top left side (E ) and top left trim (J).
F
K
Top
unfinished edge
5
8
4
K
F
4
8
5
Step 5 - Attaching the Top Trim to the Top Side Panel.
J
Repeat for the top left side (E ) and top left trim (J).
E
Top
5x 6
8x 6
4x 4

Pg 9 of 44 [phone] IS92230-I3
1
4
C
F
E
7
4
F
C
4
3
• Insert dowels (4) into the top right and left side panels (E and F)and top trim (G).
•Attach the fixed shelf (C) and the top trim (G) to the top side panels (E and F).
•Attach the hanging rail (I) to the top side panels (E and F).
•Attach the slotted brackets (7) to the top trim (J and K), as shown.
• Tighten cams (3) by turning them clockwise approximately a half turn or until snug. DO NOT OVERTIGHTEN!
5
1
G
I
Step 6 - Attaching the Top Side Panels to the Fixed Shelf.
3
4x 6
1x 4 5x 2

Pg 10 of 44 [phone] IS92230-I3
• Attach cambolts (2) to the top panel (A), as shown.
• Attach cambolts (2) to the middle shelf (D), as shown.
A
D
unfinished edge
2
2
2
unfinished edge
2
2
2
Step 7 - Installing Cambolts to the Top Panel.
Step 8 - Installing Cambolts to the Middle Shelf.
2
2x 8
2x 4

Pg 11 of 44 [phone] IS92230-I3
• Insert dowels (4) into the top side panels (E and F), as shown.
• Attach the middle shelf (D) to the top side panels (E and F), as shown.
1
D
F
E
D
F
1
4
4
1
Step 9 - Attaching the Middle shelf.
1x 4
4x 4

Pg 12 of 44 [phone] IS92230-I3
•Insert dowels (4) into the top side panels (E and F), as shown.
•Attach the top panel (A) to the top side panels (E and F), as shown.
• Tighten cams (3) by turning them clockwise approximately a half turn or until snug. DO NOT OVERTIGHTEN!
F
F
E
3
3
A
A
4
4
2
2
Step 10 - Attaching the Top Panel.
4x 8

Pg 13 of 44 [phone] IS92230-I3
•Insert cams (3) into the bottom trim (L) and the top support rail (M). NOTE the direction of the cams (3).
3
L
Step 11 - Installing Cams to the Bottom Trim and Top Support Rail.
NOTE the direction
of the cams (3).
Step 12 - Attaching Cambolts to the Leg Assemblies.
• Insert cams (3) into the leg assemblies (O and P). NOTE the direction of the cams (3).
• Attach cambolts (2) to the leg assemblies (O and P), as shown.
M
3
3
2
2
3
O
P
NOTE the direction
of the cams (3).
3x 6
3x 2
2x 4

Pg 14 of 44 [phone] IS92230-I3
Step 13 - Attaching the Leg Assemblies to the Bottom Trim and Top Support Rail.
•Attach the leg assemblies (O and P) to the bottom trim (L) and the top support rail (M), as shown.
• Tighten cams (3) by turning them clockwise approximately a half turn or until snug. DO NOT OVERTIGHTEN!
Back
O
P
L
M
M
P
4
4
unfinished edge
4x 4

Pg 15 of 44 [phone] IS92230-I3
•Attach feet (20) to the legs, as shown. NOTE: If necessary, lightly tap the foot (20) with a hammer.
• Carefully lay the cabinet body over and lay face up on the floor.
• Insert dowels (4) into the middle shelf (D), as shown.
•With the bottom trim (L) facing up, carefully attach the leg assembly to the middle shelf (D), as shown.
• Tighten all cams (3) by turning it clockwise approximately a half turn or until snug. DO NOT OVERTIGHTEN!
U
D
42
4
Back
20
L
M
20
D
Step 14 - Attaching the Top assembly to the Bottom assembly.
top assembly
bottom assembly
4x 4
20 x 4

Pg 16 of 44 [phone] IS92230-I3
Correct!!
Incorrect!!
A
A
• NOTE: Hold the top panel (A) and slowly stand the assembly upright,
as shown.
RECOMMEND
RECOMIENDA
RECOMMANDÉ
Step 15 - Carefully stand the assembly upright.

Pg 17 of 44 [phone] IS92230-I3
• Attach the magnet strike (17) to door (W), as shown. DO NOT OVERTIGHTEN MAGNET
STRIKE SCREW (18)!
• Attach door (W) to the hinges (6), as shown. NOTE: DO NOT OVERTIGHTEN HINGE SCREWS (5)!
•Attach a door handle (10) to the door (W), as shown.
• Repeat for the other door (W).
W
9
5
10
17
18
RECOMMEND
RECOMIENDA
RECOMMANDÉ
Step 16 - Attaching the Doors.
Repeat for the top left door (W).
W
18
17
5
9
5x 8
9x 4
10 x 2
17 x 2
18 x 2

Pg 18 of 44 [phone] IS92230-I3
Hinge
Hinge
Door
Door
• Horizontal Adjustment, (IN AND OUT).
• Vertical Adjustment, (UP AND DOWN).
Step 17 - Hinge Adjustments.

Pg 19 of 44 [phone] IS92230-I3
•We recommend two people carefully stand the assembly up.
•With the seam side of back panel (X) facing out, attach to the back of the unit.
• NOTE: Make sure the mounting holes are at the top and lined up with holes in the
hanging rail (I), as shown.
X
12
mounting holes
Helpful Hint:
To help align the back panel properly,
fasten a nail in each
of the corners of the back panel first.
RECOMMEND
RECOMIENDA
RECOMMANDÉ
Step 18 - Attaching the Back Panel.
12 x 22

Pg 20 of 44 [phone] IS92230-I3
• Mark the location on wall through the mounting holes on the hanging rail (I).
• Drill holes in the marked spots on the wall. If screws will not be going directly into studs, insert wall anchors (21).
• Complete mounting by tightening mounting screws (22) through mounting spacers (23) into studs or
wall anchors (21).
• Insert adjustable shelf (B), using the shelf clips (11).
B
11
11
23
22
Step 19 - Mounting the unit to the wall.
RECOMMEND WARNING:
BEFORE CUTTING OR DRILLING INTO ANY WALL SURFACE, VERIFY THE LOCATION OF ELECTRICAL,
PLUMBING AND GAS LINES. CUTTING ANY OF THESE MAY CAUSE SERIOUS INJURY.
• It is imperative that the unit be fastened to the wall for safety and stability.
• For safety reasons, it is imperative to use a stepladder.
21 x 2
22 x 2
23 x 2
11 x 4