Better Homes and Gardens Espresso Finish User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-04-10 Rev. 0001-A Factory: KONRIC
Steele TV Stand
Stock # BH18-084-097-18 Espresso Finish
# BH18-084-097-19 White Finish
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Steele TV Stand
MODEL # BH18-084-097-18 / BH18-084-097-19
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM RECOMMENDED WEIGHT LOADS
FITS UP TO MOST 42”-55” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.3 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
PLACE TV BEHIND THE STOPPER

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Side Panel (Qty. 4) C- Upper Fixed Shelf / Bottom Panel (Qty. 2)
D- Lower Fixed Shelf (Qty. 1) E- Right Partition Panel (Qty. 1) F- Left Partition Panel (Qty. 1)
G- Left Support (Qty. 1) H- Right Support (Qty. 1) I- Bottom Back Stretcher (Qty. 1)
J- Upper Back Stretcher (Qty. 1) K- Stop Rail (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 26+1 extra) (Qty. 26+1 extra) (Qty. 10+1 extra)
(4) M10 x 40 mm Wood Dowel (5) 5/16" x 45 mm Bolt (6) Lock Washer
(Qty. 28+1 extra) (Qty. 12+1 extra) (Qty. 12+1 extra)
(7) Flat Washer (8) Large Plastic Cap (9) Small Plastic Cap
(Qty. 12+1 extra) (Qty. 12+1 extra) (Qty. 16+1 extra)
Hex Wrench Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 1) (Qty. 1) (Qty. 1) (Included in plastic bag)
(Not included for white finish)
Tools required: Phillips screwdriver and rubber mallet (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Lower Fixed Shelf (D), the
Supports (G and H) and the Partition Panels (E and F) using a Phillips screwdriver.
Cam Bolt
(10 used in this step)
②
H
G
F
E
D
D
2

7
Assembly Instructions
3. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), the Upper Fixed
Shelf and Bottom Panel (C).
Cam Bolt
(16 used in this step)
②
x2
A
C
2

8
Assembly Instructions
4. Glue four 40 mm Wood Dowels (4) into the inner holes of the Side Panels (B) and attach them to the
Top Panel (A) by engaging four Cam Locks (1) (Refer to page 3 on Cam Lock system operation
supplement).
A
B
B
1
4
Cam Lock
(4 used in this step)
①
M10 x 40 mm Wood Dowel
(4 used in this step)
④

9
Assembly Instructions
5. Glue four 40 mm Wood Dowels (4) into the inner holes on the Side Panels (B).
6. Position the Upper Fixed Shelf (C) onto the inserted Wood Dowels (4) and fasten it in place with four
45 mm Bolts (5) and four Washers (6 and 7).
Lock Washer
(4 used in this step)
⑥
Flat Washer
(4 used in this step)
⑦
M10 x 40 mm Wood Dowel
(4 used in this step)
④
5/16" x 45 mm Bolt
(4 used in this step)
⑤
C
B
B
5
6
7
4

10
Assembly Instructions
7. Attach the Upper Back Stretcher (J) between the Partition Panels (E and F) with two Cam Locks (1) and
two 30 mm Wood Dowels (3).
3
3
1
1
F
E
J
Cam Lock
(2 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③

11
Assembly Instructions
8. Attach the previous assembly to the Fixed Shelf (C) with six Cam Locks (1), two 30 mm Wood Dowels
(3) and four 40 mm Wood Dowels (4).
C
E
F
2
4
1
3
21
M8 x 30 mm Wood Dowel
(2 used in this step)
③
Cam Lock
(6 used in this step)
①
M10 x 40 mm Wood Dowel
(4 used in this step)
④

12
Assembly Instructions
9. Glue the Wood Dowels (3 and 4) into the inner holes on the Partition Panels (E and F) and the Back
Stretcher (J).
10. Position the Lower Fixed Shelf (D) onto the inserted Wood Dowels (3 and 4) and fasten it in place with
four 45 mm Bolts (5) and four Washers (6 and 7).
M8 x 30 mm Wood Dowel
(2 used in this step)
③
M10 x 40 mm Wood Dowel
(4 used in this step)
④
Cam Lock
(2 used in this step)
①
Lock Washer
(4 used in this step)
⑥
Flat Washer
(4 used in this step)
⑦
D
5
6
7
4
3
1
F
E
5/16" x 45 mm Bolt
(4 used in this step)
⑤

13
Assembly Instructions
11. Glue four 40 mm Wood Dowels (4) into the inner holes of the Side Panels (B) and attach them to the
Lower Fixed Shelf (D) by engaging four Cam Locks (1).
Cam Lock
(4 used in this step)
①
M10 x 40 mm Wood Dowel
(4 used in this step)
④
B
B
14
D

14
Assembly Instructions
12. Glue four 40 mm Wood Dowels (4) into the inner holes on the Side Panels (B).
13. Position the Upper Fixed Shelf (C) onto the inserted Wood Dowels (4) and fasten it in place with four
45 mm Bolts (5) and four Washers (6 and 7).
M10 x 40 mm Wood Dowel
(4 used in this step)
④
Lock Washer
(4 used in this step)
⑥
Flat Washer
(4 used in this step)
⑦
5/16" x 45 mm Bolt
(4 used in this step)
⑤
C
5
4
6
7
B
B

15
Assembly Instructions
14. Attach the Bottom Back Stretcher (I) between the Supports (G and H) with two Cam Locks (1) and two
30 mm Wood Dowels (3).
3
1
1
3
I
G
H
Cam Lock
(2 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③

16
Assembly Instructions
15. Attach the previous assembly to the Bottom Panel (C) with six Cam Locks (1), two 30 mm Wood
Dowels (3) and four 40 mm Wood Dowels (4).
4
1
H
G
C
31
M8 x 30 mm Wood Dowel
(2 used in this step)
③
Cam Lock
(6 used in this step)
①
M10 x 40 mm Wood Dowel
(4 used in this step)
④

17
Assembly Instructions
16. Ask for assistance to stand the unit upright.
17. Cover the countersunk holes by inserting the provided Plastic Caps (8 and 9). Gently tap the Plastic
Caps with a rubber mallet to ensure they are fully seated.
NOTE: You must install the Strip Stopper to prevent the TV from tipping when placing your flat panel
television directly on the console.
18. Remove the paper backing from the Stop Rail (K), then properly align the Stop Rail with the top edge of
the stopper template on the Top Panel (A). Press down on the Stop Rail to help adhesion.
19. Carefully remove the stopper template from the Top Panel (A).
9
K
8
Large Plastic Cap
(12 used in this step)
⑧
Small Plastic Cap
(16 used in this step)
⑨

18
Assembly Instructions
Tools required (not provided): Phillips screwdriver, stud finder, power drill and 3 mm/0.1 in drill bit.
20. Ask for assistance to position the unit at the desired location against a wall.
21. Follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach
the tip-over restraints to the unit and the wall.
NOTE: The tipping restraint hardware included is for wooden stud wall construction. It must be
attached to a wall stud. Depending upon your wall construction, different anchor hardware maybe
required. Please contact your local hardware store for assistance. Young children can be seriously
injured by tipping furniture. You must install the Tipping Restraint Hardware with the unit to
prevent the unit from tipping, causing any accidents or damage. The tipping restraints are intended
only as a deterrent, they are not a substitute for proper adult supervision. The tipping restraints are
not earthquake restraints. If you wish to add the extra security of earthquake restraints, they must be
purchased and installed separately.
22. The unit is now ready for use.

19
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further Advice about Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Follow these important and helpful tips
that will enhance your furniture as it ages.
A touch-up pen has been provided to minimize the small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is
designed to meet your highest expectations. We guarantee that you will immediately see the value of
our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
State to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com