Better Homes and Gardens ADAIR CREDENZA BH47-021-199-10 User manual

PB 1
model# BH47-021-199-10
model# BH47-021-199-11
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
champagne
black
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
ADAIR CREDENZA

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BOTTOM ASSEMBLY
LOWER RAIL
BACK PANEL
UPPER RAIL
REAR UPPER RAIL
A
B
C
D
E
F
G
H
PARTITION
ADJUSTABLE SHELF [X2]
LEFT DOOR
RIGHT DOOR
FOOT
I
J
K
L
M
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Bolt
x4
3. Cam
x16
4. 15mm Pan Head
Screw
x23
1. Wood Dowel
x24
2. Cam Bolt
x16
6. Lock Washer
x4
7. Washer
x6

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
12. Wall Strap
x1
10. Wall Screw
x1
11. 19mm Pan Head
Screw
x1
8. Allen Wrench
x1
9. Shelf Pin
x8
13. Wall Anchor
x1
14. 32mm Pan Head
Screw
x6

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x2 x4 x4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x2 x2 x2
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x2 x4 x2
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x2 x2
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x4 x4 x4
STEP 5
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x12 x2
x4
x2
x4
x4
x1
STEP 6
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt
6. Lock
Washer
3. Cam
7. Washer
5. Bolt
8. Allen
Wrench
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
FRONT

12
x6
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 7
14. 32mm
Pan Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12 13
x23
STEP 8
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
4. 15mm Pan
Head Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.
hole for anti-tip strap

14
x8
STEP 9
1. Insert shelf supports into desired holes. Dierent holes accommodate dierent shelf heights.
2. Angle shelves to t between the rails and set on top of shelf supports.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
9. Shelf Pin
Finished Edge

14 15
STEP 10

16
x1x1x1x1
x2
13
10
11
7
7
12
STEP 11
11. 19mm
Pan Head
Screw
10. Wall
Screw
12. Wall
Strap
7. Washer
13. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

16 17
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
For use with televisions weighing
35 pounds (15.9 kg) or less. Use with
heavier televisions may result in
instability causing tip over resulting
in death or serious injury.
Use of anti-tip restraints may only
reduce, but not eliminate, the risk
of tip-over.
! WARNING
90 lbs general use /
35 lbs. television use
25 lbs per shelf
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH47-021-199-10
model# BH47-021-199-11
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
champán
negro
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
TRINCHADOR ADAIR
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
ENSAMBLE INFERIOR
RIEL INFERIOR
PANEL POSTERIOR
RIEL SUPERIOR
RIEL SUPERIOR TRASERO
A
B
C
D
E
F
G
H
DIVISOR
REPISA AJUSTABLE [X2]
PUERTA IZQUIERDA
PUERTA DERECHA
PATA
I
J
K
L
M
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Perno
x4
3. Leva
x16
4. 15mm tornillo de
cabeza de noria
x23
1. Clavija de Madera
x24
2. Tornillo de Leva
x16
6. Arandela Fijadora
x4
7. Arandela
x6