Better Homes and Gardens SAVANNAH BH17-021-199-21 User manual

1PB
model# BH17-021-199-21
model# BH17-021-199-22
model# BH17-021-199-20
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
gray
teal
ivory
SAVANNAH ACCENT TABLE

2
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BOTTOM PANEL
BACK PANEL
FRONT RAIL
BACK RAIL
BOTTOM FRONT PANEL
DRAWER FACE
LEFT DRAWER SIDE
RIGHT DRAWER SIDE
DRAWER BACK
DRAWER BOTTOM
A
B
C
D
E
F
G
H
I
J
K
L
M
TOOLS NEEDED
PARTS LIST
Flat Head Screwdriver Phillips Head Screwdriver

2 3
HARDWARE LIST
6. Knob Bolt
x1
7. 25mm Flat Head
Screw
x8
5. Knob
x1
4. 15mm Pan Head
Screw
x10
3. Cam
x15
2. Cam Bolt
x15
1. Wood Dowel
x19
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.

4
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

4 5
x4 x4 x4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6
x4 x4 x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

76
x6 x5 x5
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

8
x10
STEP 4
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
4. 15mm Pan
Head Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.
pre-drilled holes

98
x5 x2 x2
STEP 5
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

10
x8
STEP 6
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
7. 25mm Flat
Head Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

1110
x1x1
STEP 7
5. Knob 6. Knob Bolt

12
35 lbs. / 15.9 kg.
30 lbs. / 13.6 kg.
20 lbs. / 9.1 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

1PB
model# BH17-021-199-21
model# BH17-021-199-22
model# BH17-021-199-20
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Instrucciones de Ensamble
gris
azul verde
marl
MESA DE ACENTO
SAVANNAH

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
PANEL INFERIOR
PANEL POSTERIOR
RIEL FRONTAL SUPERIOR
RIEL TRASERA POSTERIOR
PANEL FRONTAL INFERIOR
FRENTE DE LA GAVETA
CAJÓN IZQUIERDO
CAJÓN DERECHO
CAJÓN TRASERA
PARTE DEL CAJÓN INFERIOR
A
B
C
D
E
F
G
H
I
J
K
L
M
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza Plana Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
6. Perno de Perilla
x1
7. 25mm Tornillo de
Cabeza de Plana
x8
5. Perilla
x1
4. 15mm Tornillo de
Cabeza de Noria
x10
3. Leva
x15
2. Tornillo de Leva
x15
1. Clavija de Maderat
x19

4
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

4 5
x4 x4 x4
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6
x4 x4 x4
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva

76
x6 x5 x5
PASO 3
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva

8
x10
PASO 4
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
4. 15mm
Tornillo de
Cabeza de
Noria
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
Empiece instalando todos los tornillos a lo
largo de la orilla del panel posterior. Después,
utilzando un cuadro o una cinta métrica,
asegúrese de que el gabinete esté cuadrado.
(si utiliza una cinta métrica, la distancia de una
esquina, en diagonal a la otra esquina debe de
ser la misma en ambas direcciones.) Instalar
los tornillos restantes, comenzando con las
esquinas.
los agujeros
pretaladrados