Better Homes and Gardens BH15-084-899-12 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-06-23 Rev. 0001-C Factory: KONRIC
Media Fireplace Console
Stock # BH15-084-899-12
# BH46-084-899-07
# BH46-084-899-08
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Media Fireplace Console
MODEL #: BH15-084-899-12 / BH46-084-899-07 / BH46-084-899-08
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted
slightly, turn the appropriate screw, as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
FITS UP TO MOST 65” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL
OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
13
2

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw Cam Bolt into the pre-drilled small holes on panel. Connect both panels together; making
sure Cam Bolt goes into pre-drilled hole on the end of panel with Cam Lock.
2. Insert Cam Lock into pre-drilled large hole on panel. Make sure arrow on Cam Lock is pointed toward
Cam Bolt.
3. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten Cam Lock
clockwise.
4. Plug Cam Cap into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (1) B- Upper Side Panel (2) C- Upper Partition Panel (1)
D- Fixed Shelf (1) E- Left Lower Side Panel (1) F- Right Lower Side Panel (1)
G- Left Lower Partition Panel (1) H- Right Lower Partition Panel (1) I- Middle Crossbar Assembly (1)
J- Bottom Panel (1) K- Base Front Molding (1) L- Base Rear Stretcher (1)
M- Right Door (1) N- Left Door (1) O- Upper Back Panel (1)
P- Lower Back Panel (2) Q- Firebox Support (1) R- Adjustable Shelf (2)

5
Parts and Hardware List
S- Stop Rail (1) Fireplace Insert (1) Remote Control with Battery (1)
(1) Cam Lock (2) Cam Bolt (3) Ø8 x 30 mm Wood Dowel
(35+1 extra) (35+1 extra) (34+1 extra)
(4) Ø3.5 x 12 mm Screw (5) Ø4 x 19 mm Screw (6) Ø4 x 40 mm Wood Screw
(12+1 extra) (2+1 extra) (4+1 extra)
(7) Ø3.5 x 15 mm Washer Head Screw (30+1 extra) (8) 2” Lag Bolt (2) (9) Straight Metal Bracket (2)
(10) Handle and Back Plate (2) (11) 15 mm Handle Bolt (2) (12) Angle Metal Bracket (2)
(13) Floor Leveler (14) Rubber Bumper (15) Shelf Pin (16) Cam Lock Cover
(2) (4+1 extra) (8+1 extra) (26+1 extra)
Glue (1) Touch-up Pen (1) Tipping Restraint Hardware Kit (2)
(Not included for item #BH46-084-899-07) (Included in plastic bag)
Tools required: Phillips screwdriver and hammer (not provided).