Better Homes and Gardens Steele Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-09-24 Rev. 0001-A Factory: HESLTD
Steele End Table
Stock # BH46-021-199-01
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOGUE: Steele End Table (BH46-021-199-01)
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 10 lb. (4.5 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the fireplace.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) C- Right Side Panel (Qty. 1)
D- Bottom Panel (Qty. 1) E- Fixed Shelf (Qty. 1) F- Back Panel (Qty. 1)
G- Bottom Short Support (Qty. 2) H- Bottom Long Support (Qty. 2) I- Drawer Front
(Qty. 1) (Qty. 1) (Qty. 1)
J- Drawer Left Side K- Drawer Right Side L- Drawer Back Panel M- Drawer Bottom Panel
(Qty. 1) (Qty. 1) (Qty. 1) (Qty. 1)
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 4+1 extra) (Qty. 12+1 extra) (Qty. 16+1 extra)
(4) M8 x 30 mm Wood Dowel (5) M4 x 38 mm Screw (6) M4 x 50 mm Screw
(Qty. 20+1 extra) (Qty. 4+1 extra) (Qty. 12+1 extra)
(7) Handle (Qty. 1) (8) Handle Bolt (Qty. 2) (9) Cam Lock Cover (Qty. 4+1 extra)
(10) M15 x 60 mm Wood Dowel (Qty. 8+1 extra) Glue (Qty. 1) Touch-up Pen (Qty. 1)
Tools required: Phillips screwdriver and hammer (not provided).

5
Drawer Assembling
1. Unpack the unit and confirm that you have all the hardware and required parts.
Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw 4 Cam Bolts (3) into the designated small holes on the Drawer Front (I).
3. Connect Drawer Left and Right Side Panels (J and K) to the Drawer Front (I) by engaging four Small
Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
1
3
3
I
J
K
Small Cam Lock
(4 used in this step)
①
Cam Bolt
(4 used in this step)
③

6
Drawer Assembling
4. Slide the Drawer Bottom Panel (M) into the grooves between the Drawer Side Panels (J and K) until
fully inserted into the Drawer Front (I).
I
J
K
M

7
Drawer Assembling
5. Fasten the Drawer Back Panel (L) to the Drawer Side Panels (J and K) with four 38 mm Screws (5).
Make sure that Drawer Bottom Panel (M) fits securely into the groove of the Drawer Back Panel (L).
Tighten all the screws with a Phillips screwdriver.
I
J
K
M
L
5
5
I
J
K
M
L
M4 x 38 mm Screw
(4 used in this step)
⑤

8
Drawer Assembling
6. Turn the assembled drawer upright.
7. Attach the Handle (7) to the outside of the Drawer Front (I) with two Handle Bolts (8).
8
7
8
I
Handle Bolt
(2 used in this step)
⑧
Handle
(1 used in this step)
⑦

9
Assembly Instructions
8. Attach the Bottom Long Supports (H) between the Bottom Short Supports (G) with four 30 mm Wood
Dowels (4).
9. Fasten the previous assembly to the Bottom Panel (D) with eight 30 mm Wood Dowels (4) and eight 50
mm Screws (6).
H
H
G
G
4
4
4
4
4
4
44
6
6
6
6
G
H
G
H
D
M8 x 30 mm Wood Dowel
(12 used in this step)
④
M4 x 50 mm Screw
(8 used in this step)
⑥

10
Assembly Instructions
10. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A), the Side Panels
(B and C), the Bottom Panel (D) and the Fixed Shelf (E) using a Phillips screwdriver.
Cam Bolt
(12 used in this step)
③
3
A
E
B
C
D

11
Assembly Instructions
11. Attach the Back Panel (F) to the Fixed Shelf (E) with one 30 mm Wood Dowel (4) and two Cam Locks
(2) making sure the cam locks will face inward.
E
F2
2
4
Large Cam Lock
(2 used in this step)
②
M8 x 30 mm Wood Dowel
(1 used in this step)
④

12
Assembly Instructions
12. Attach the Fixed Shelf assembly to the Right Side Panel (C) with three 30 mm Wood Dowels (4) and
two Cam Locks (2).
E
F
C
2
24
4
Large Cam Lock
(2 used in this step)
②
M8 x 30 mm Wood Dowel
(3 used in this step)
④

13
Assembly Instructions
13. Repeat the same procedure to attach the Left Side Panel (B) at the opposite end.
Large Cam Lock
(2 used in this step)
②
M8 x 30 mm Wood Dowel
(3 used in this step)
④
4E
F
2
2
B
C
4

14
Assembly Instructions
14. Attach the Top Panel (A) to the Side Panels (B and C) with four 60 mm Wood Dowels (10) and four
Cam Locks (2).
Large Cam Lock
(4 used in this step)
②
10
10
2
2
A
B
C
M15x 60 mm Wood Dowel
(4 used in this step)
⑩

15
Assembly Instructions
15. Insert four 60 mm Wood Dowels (10) into the bottom holes on the Side Panels (B and C) and insert one
30 mm Wood Dowel (4) into the middle hole on the Back Panel (F). Position the Bottom Panel (D) onto
the inserted wood dowels and attach to the Back Panel (F) with two Large Cam Locks (2).
Large Cam Lock
(2 used in this step)
②
M8 x 30 mm Wood Dowel
(1 used in this step)
④
2
2
4
10
10
10
B
C
D
10
M15x 60 mm Wood Dowel
(4 used in this step)
⑩

16
Assembly Instructions
16. Fasten the Bottom Panel (D) to the Side Panels (B and C) with four 50 mm Screws (6).
M4 x 50 mm Screw
(4 used in this step)
⑥
D
B
C
6
6

17
Assembly Instructions
17. Plug the Cam Lock Covers (9) onto the visible Cams Locks to conceal the Cams.
18. Insert the assembled drawer into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (B
and C) all the way forward (including ball bearing cart). Then align the Slide Runners on the assembled
drawer with the Slide Tracks and push the drawer carefully inside until it stops.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step. If you need to
remove the drawer, please pull the drawer all the way out, then simultaneously push the plastic release
lever of the ball bearing slides up on one side and down on the other side, and then pull it completely
out.
BC
I
J
K
9
Cam Lock Cover
(4 used in this step)
⑨

18
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or
shipping. We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace
it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your
highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State
(province to province).
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2016-09-24 Rev. 0001-A Fábrica: HESLTD
Mesa esquina Steele
Serie # BH46-021-199-01
ENSAMBLE REQUERIDO POR ADULTO
Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a
la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
O visite nuestra página de Internet 24 horas al dia, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: / /

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Mesa esquina Steele (BH46-021-199-01)
HECHO EN CHINA
NOTA ESPECIAL
Por favor lea todo el instructive antes de ensamblar. Examinar todo el material de
empaque antes de tirar el cartón. Retirar cualquier grapas del cartón antes de tirar. Retirar
todas las partes del cartón y separar en grupos como es indicado en la lista de partes. Por
favor de asegurar que todas las partes estan presentes antes del ensamble. El uso de
herramientas eléctricas para completer el ensamble no es recomendado.
MÁXIMOS PESOS RECOMENDADOS
MÁXIMA CARGA 50 lb. (22.6 kg)
MÁXIMA CARGA 10 lb. (4.5 kg)
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES
.