Better Homes and Gardens Canton BHS336158813034 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-03-31 Rev. 0001-A
Canton Round Dining Table
Stock # BHS336158813034
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
1. Maximum load weight 90.7 kg (200 pounds).
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
M A X I M U M R E C O M M E N
D E D
W E
I G H T L O A D S
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
,
T
I
P
S
A
N
D
T
R
I
C
K
S

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (Qty. 1) B- Mounting Panel (Qty. 1)
C- Lower Base (Qty. 1) D- Upper Base (Qty. 1)
E- Post (Qty. 1) F- Decor (Qty. 8)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) 1/4” x 32 mm Bolt (2) 1/4” x 75 mm Bolt
(Qty. 21+1 extra) (Qty. 5+1 extra)
(3) Lock Washer (4) Flat Washer
(Qty. 26+1 extra) (Qty. 26+1 extra)
(5) M8 x 30 mm Wood Dowel (6) Wood Plug
(Qty. 28+1 extra) (Qty. 8+1 extra)
Hex Wrench (Qty. 1) Touch-up Pen (Qty. 1)
Tools required: Hex wrench (provided), Phillips screwdriver and rubber mallet (not provided).

5
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Unscrew the screws which hold the nylon straps onto the underneath of the Table Top (A) and remove
the components from the inner boxes.
3. Proceed to remove the Mounting Panel (B) from the Table Top (A) by unscrewing the nylon strap.
DO NOT fully tighten the bolts or screws initially until all the bolts or screws
are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the bolts or screws.
Nylon strap

6
Assembly Instructions
4. Insert two Wood Dowels (5) into the side holes of each Decor (F) and attach it to the Post (E) with one
32 mm Bolt (1), one Lock Washer (3) and one Flat Washer (4).
① x 8
431
431
5
5
F
E
F
F
F
F
③ x 8
④ x 8
⑤ x 16

7
Assembly Instructions
5. Insert six Wood Dowels (5) into the non-threaded holes on the Post (E) and four Decors (F) as shown.
6. Align and attach the Mounting Panel (B) to the top of the previous assembly by inserting five 32 mm
Bolts (1) with the Washers (3 and 4) through the countersunk holes of the Mounting Panel (B) and
screw into place. Securely tighten the bolts with the Hex Wrench provided.
① x 5
③ x 5
④ x 5
⑤ x 6
The countersunk holes
4
3
1
5
5
5
E
F
F
B

8
Assembly Instructions
7. Flip the previous assembly around on the Mounting Panel (B). Insert six Wood Dowels (5) into the non-
threaded holes on the Post (E) and other four Decors (F) at the opposite end.
8. Combine the Lower and Upper Bases (C and D) together.
9. Align the drilled holes on the assembled Base (C and D) with the inserted Wood Dowels (5) and press
them together.
10. Insert five 75 mm Bolts (2) with the Washers (3 and 4) through the countersunk holes on the Bases (C
and D) and securely screw into place with the hex wrench provided.
② x 5
③ x 5
④ x 5
⑤ x 6
4
3
2
5
5
5
F
F
E
D
CC
D

9
Assembly Instructions
11. Ask for assistance to position the Table Top (A) upside down on a level and protected surface.
12. Align and attach the assembled Mounting Panel (B) to the Table Top (A) with eight 32 mm Bolts (1) and
eight Washers (3 and 4).
13. Now, go back and securely tighten all the bolts. Make sure all the parts are tight and there are no gaps
between the parts. This will keep the unit square.
① x 8
③ x 8
④ x 8
4
3
1
B
A

10
Assembly Instructions
14. Cover the countersunk holes on the Decors (F) with the provided Wood Plugs (6). Gently tap the Wood
Plugs with a rubber mallet to ensure they are fully seated.
⑥ x 8
6
6
F
F

11
Assembly Instructions
15. Ask for assistance to lift the unit upright and position it at the desired location.
16. If necessary, adjust the pre-attached floor levelers at the bottom of Bases (C and D) to level the unit.
Floor leveler

12
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice about Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Follow these important and helpful tips
that will enhance your furniture as it ages.
A touch-up pen has been provided to minimize the small nicks or scratches that may occur during assembly or
shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to
State.
Whalen Furniture Manufacturing
1578 Air Wing Road, San Diego CA, 92154, USA
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2023-03-31 Rev. 0001-A
Mesa comedor redonda Canton
Modelo # BHS336158813034
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a
la tienda donde lo compro. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
1-866-942-5362
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
O visite nuestra página de Internet 24 horas al día, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
NÚMERO de LOTE:__________
FECHA de COMPRA: / /

2
1. Máximo peso recomendado de 90.7 kg (200 libras).
1. Por favor lea el instructivo antes de comenzar el ensamble.
2. Para evitar daños, ensamblar el producto en una superficie fuerte, nivelada y libre de abrasivos.
3. Mantenga todo el material de ferretería fuera del alcance de niños.
4. Esperar hasta que todos los pasos estén completados antes de apretar los pernos.
5. Asegurar de que los pernos y tuercas estén apretados antes de usar la unidad.
6. Revisar que los pernos, tuercas y perillas estén apretados cada 3 meses o como sea necesario.
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES.
MÁ X I MO P E SO R EC O ME ND A DO
I NF OR M AC I ÓN GE N ER A L , RE C OM EN D AC ION ES Y TR U CO S

3
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de
ferretería antes de iniciar el ensamblado.
A- Tapa de la mesa (Cant. 1) B- Panel de montaje (Cant. 1)
C- Base inferior (Cant. 1) D- Base superior (Cant. 1)
E- Poste (Cant. 1) F- Moldura decorativa (Cant. 8)

4
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de
ferretería antes de iniciar el ensamblado.
(1) Perno de 1/4 de pulgada x 32 mm (2) Perno de 1/4 de pulgada x 75 mm
(Cant. 21+1 extra) (Cant. 5+1 extra)
(3) Arandela de presión (4) Arandela plana
(Cant. 26+1 extra) (Cant. 26+1 extra)
(5) Clavija de madera de M8 x 30 mm (6) Tapa de madera
(Cant. 28+1 extra) (Cant. 8+1 extra)
Llave hexagonal (Cant. 1) Plumón (Cant. 1)
Herramientas requeridas: Llave hexagonal (provista), desarmador estrella y mazo de goma (no provisto).

5
Instructivo de ensamble
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños.
2. Desatornillar los pernos que sujetan las correas de nylon sobre la parte inferior de la tapa de la mesa (A)
y retirar los componentes de las cajas interiores.
3. Proceder a retirar el panel de montaje (B) de la tapa de la mesa (A) desatornillando la correa de nylon.
Correa de Nylon
NO apriete los pernos hasta que todos los pernos estén listos para el ensamble.
Para evitar daños a la rosca, NO sobre apriete los pernos.

6
Instructivo de ensamble
4. Insertar 2 clavijas de madera (5) en los agujeros laterales de cada moldura decorativa (F) y adjuntar al
poste (E) con un perno de 32 mm (1), una arandela de presión (3) y una arandela plana (4).
① x 8
431
431
5
5
F
E
F
F
F
F
③ x 8
④ x 8
⑤ x 16

7
Instructivo de ensamble
5. Insertar 6 clavijas de madera (5) en los agujeros no roscados en el poste (E) y en las 4 decoraciones (F)
como se muestra.
6. Alinear y adjuntar el panel de montaje (B) a la parte superior del ensamble previo insertando 5 pernos
de 32 mm (1) con las arandelas (3 y 4) a través de los agujeros avellanados en el panel de montaje (B) y
atornillar en su lugar. Apretar los pernos con la llave hexagonal provista.
① x 5
③ x 5
④ x 5
⑤ x 6
Los agujeros avellanados
4
3
1
5
5
5
E
F
F
B

8
Instructivo de ensamble
7. Voltear el ensamble previo sobre el panel de montaje (B). Insertar 6 clavijas de madera (5) en los
agujeros no roscados en el poste (E) y en las otras 4 molduras decorativas (F) al extremo opuesto.
8. Combinar las bases inferior y superior (C y D).
9. Alinear los agujeros perforados en la base ensamblada (C y D) con las clavijas de madera insertadas (5)
y presionar para juntar.
10. Insertar 5 pernos de 75 mm (2) con las arandelas (3 y 4) a través de los agujeros avellanados en las
bases (C y D) y atornillar en su lugar con la llave hexagonal provista.
② x 5
③ x 5
④ x 5
⑤ x 6
4
3
2
5
5
5
F
F
E
D
CC
D