Better Homes and Gardens RHODES BH18-021-199-27 User manual

PB 1
model# BH18-021-199-27
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
dark brown oak/black
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
RHODES DESK

2
TOP PANEL
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
BACK PANEL
LEFT SIDE FRAME
RIGHT SIDE FRAME
A
B
C
D
E
F
G
DRAWER FRONT
DRAWER FRONT BACK
DRAWER LEFT SIDE
DRAWER RIGHT SIDE
DRAWER BACK
DRAWER BOTTOM
DRAWER SUPPORT [X2]
H
I
J
K
L
M
N
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Flat Head ScrewdriverHammer Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Large Bolt
x8
3. Wood Dowel
x10
4. Flat Head Screw
x16
1. Cam
x16
2. Cam Bolt
x16
6. Small Bolt
x4
7. Allen Wrench
x1

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
12. Wall Anchor
x1
10. Short Pan
Head Screw
x1
11. Wall Strap
x1
8. Large Pan
Head Screw
x5
9. Pull Bolt
x4
13. Pull
x2
14. Washer
x2

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x6 x9
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
3. Wood
D o w e l
2. Cam Bolt
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4 x7 x3
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
3. Wood
D o w e l
2. Cam Bolt 1. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x13
STEP 3
1. Refer to page 5 for instructions on how to use the cam lock system.
1. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x8
(H6)
(H5)
(H6)
(H5)
x4 x1
1. Make sure the bolts go through the pre-drilled holes properly.
2. Do not over tighten bolts.
STEP 4
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
5. Large Bolt 6. Small Bolt 7. Allen
Wrench

10
x4 x4
(H4)
(H8)
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 5
4. Flat Head
Screw
8. Large Pan
Head Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x12
(H9)
(H9)
x4 x2
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 6
4. Flat Head
Screw
9. Pull Bolt 13. Pull
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
STEP 7

1312
x1x1x1x1
x2
12
8
10
14
14
11
STEP 8
10. Short
Pan Head
Screw
8. Large
Pan Head
Screw
11. Wall
Strap
14. Washer
12. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

14
70 lbs. / 31.8 kg.
20 lbs. / 9.1 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH18-021-199-27
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
roble marrón oscuro/negro
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
ESCRITORIO RHODES
Instrucciones de Ensamble

2
PANEL SUPERIOR
PANEL INFERIOR
PANEL IZQUIERDO
PANEL DERECHO
PANEL POSTERIOR
MARCO DEL LADO IZQUIERDO
MARCO DEL LADO DERECHO
A
B
C
D
E
F
G
CAJÓN FRONTAL
CAJÓN FRONTAL POSTERIOR
CAJÓN LATERAL IZQUIERDO
CAJÓN LATERAL DERECHO
CAJÓN POSTERIOR
CAJÓN INFERIOR
SOPORTE DE CAJÓN [X2]
H
I
J
K
L
M
N
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza PlanaMartillo Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Perno Largo
x8
3. Clavija de Madera
x10
4. Tornillo de
Cabeza Plana
x16
6. Perno Pequeño
x4
7. Llave Allen
x1
2. Tornillo de Leva
x16
1.Leva
x16

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
12. Taquete de Pared
x1
10. Tornillo Corto de
Cabeza de Noria
x1
11. Cincha de Pared
x1
13. Estirador
x2
14. Arandela
x2
9.Perno de Estirador
x4
8. Tornillo Largo de
Cabeza de Noria
x5

4 5
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

6
x6 x9
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
3. Clavija de
Madera
2. Tornillo
de Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.