Better Homes and Gardens Canton Nightstand BHS336158813013 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-01-06 Rev. 0001-A
Canton Nightstand
Stock # BHS336158813013
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG : Canton Nightstand
MODEL # BHS336158813013
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D W E I G H T
L O
A D S
MAXIMUM LOAD 22.7 kg / 50 lb.
MAXIMUM LOAD 22.7 kg / 50 lb.
MAXIMUM LOAD 4.5 kg / 10 lb.
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
1234
GLUE
FINAL
1 2 43
13

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel B- Left Side Panel
(Qty. 1) (Qty. 1)
C- Right Side Panel D- Bottom Panel E- Front Crossbar
(Qty. 1) (Qty. 1) (Qty. 1)
F- Bottom Back Skirting G- Bottom Front Skirting H-Adjustable Shelf
(Qty. 1) (Qty. 1) (Qty. 1)
I- Back Panel J- Drawer Front Panel K- Drawer Back Panel
(Qty. 1) (Qty. 1) (Qty. 1)
L- Drawer Left Side Panel M- Drawer Right Side Panel N- Drawer Bottom Panel
(Qty. 1) (Qty. 1) (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 4+1 extra) (Qty. 16+1 extra) (Qty. 20+1 extra)
(4) M6 x 30 mm Small Wood Dowel (5) M8 x 30 mm Large Wood Dowel (6) M4 x 25 mm Screw
(Qty. 4+1 extra) (Qty. 16+1 extra) (Qty. 2+1 extra)
(7) M3.5 x 30 mm Screw (8) Knob (9) 5/32” x 22mm Bolt
(Qty. 4+1 extra) (Qty. 1) (Qty. 1)
(10) M3.5 x 15 mm Pan Head Screw (11) Triangle Metal Plate (12) Floor Leveler
(Qty. 8+1 extra) (Qty. 2) (Qty. 2)
(13) Shelf Support (14) M3.5 x 15 mm Washer Head Screw (15) Cam Lock Cover
(Qty. 4+1 extra) (Qty. 14+1 extra) (Qty. 4+1 extra)
Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty.1)
(Qty. 1) (Qty. 1) (Included in plastic bag)
Tools required (not provided): Phillips’s screwdriver, stud finder, tape measure, pencil, power drill and 1/8”
drill bit.

6
Assembly Instructions
NOTE: Please do not fully tighten all cam locks and screws until you finish assembling all parts. Once
assembled, go back and fully tighten all cam locks and screws. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Securely screw four Cam Bolts (3) into the designated small holes on the Drawer Front Panel (J) using a
Phillips screwdriver.
③ x 4
3
J
3

7
Assembly Instructions
3. Glue the Small Wood Dowels (4) into the inner holes on the Drawer Back Panel (K) and Drawer Side
Panels (L and M).
NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the
excess glue immediately.
④ x 4
4
L
4
M
4
4
4
K

8
7
7
K
L
M
Assembly Instructions
4. Attach the Drawer Back Panel (K) between the Drawer Side Panels (L and M) with four 30 mm Screws
(7).
Grooves line up with each
other and face inward
⑦ x 4

9
Assembly Instructions
5. Slide the Drawer Bottom Panel (N) into the grooves until fully inserted into the Drawer Back Panel (K).
K
N
L
M

10
Assembly Instructions
6. Stand the previous assembly at its back panel.
7. Position the Drawer Front Panel (J) onto the inserted Wood Dowels and fasten it in place by engaging 4
Small Cam Locks (1). (Refer to page 3 on Cam Lock system operation supplement). Make sure that the
Drawer Bottom Panel (N) fits securely into the groove of the Drawer Front Panel (J).
① x 4
L
M
N
1
J

11
Assembly Instructions
8. Install one Knob (8) to the front of the Drawer Front Panel (J) with one 22 mm Bolt (9).
⑨ x 1
⑧ x 1
J

12
Assembly Instructions
9. Securely screw the Cam Bolts (3) into the designated small holes on both Side Panels (B and C) using a
Phillips screwdriver.
③ x 8
3
B
C

13
A
D
3
Assembly Instructions
10. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A) and Bottom
Panel (D).
③ x 8

14
Assembly Instructions
11. Glue the Large Wood Dowels (5) into the inner holes on both Side Panels (B and C) as shown.
⑤ x 4
B
C
5
5
5
5

15
Assembly Instructions
12. Glue the Large Wood Dowels (5) into the inner holes on the Bottom Panel (D), Front Crossbar (E) and
Bottom Skirtings (F and G).
⑤ x 12
5
5
5
5
5
5
5
D
E
G
F

16
D
F
G
2
Assembly Instructions
13. Using the wood dowels as a guide, attach the Bottom Skirtings (F and G) to the Bottom Panel (D) by
engaging 4 Large Cam Locks (2).
② x 4
The cam locks face inward.

17
Assembly Instructions
14. Align and attach the Right Side Panel (C) to the bottom panel assembly with 3 Large Cam Locks (2).
② x 3
D
F
C
2
2

18
Assembly Instructions
15. Orient and attach the Front Crossbar (E) to the Right Side Panel (C) with 1 Large Cam Lock (2).
② x 1
The cam lock faces inward
C
2
E

19
Assembly Instructions
16. Repeat the same procedure to attach the Left Side Panel (B) to the previous assembly by engaging 4
Large Cam Locks (2).
② x 4
B
E
D
F
B
F
D
2

20
Assembly Instructions
17. Place the Top Panel (A) on both Side Panels (B and C) properly and fasten it into place with 4 Large
Cam Locks (2).
18. Now, go back and securely tighten all the cam locks and screws. Make sure that all the parts are tight
and there are no gaps between the parts. This will help keep the unit square.
② x 4
A
B
C
A
B/C
2