Better Homes and Gardens Ellis Shutter User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-03-26 Rev. 0001-A Factory: KONRIC
Ellis Shutter Door Console
Stock # BH18-084-097-49
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Ellis Shutter Door Console
MODEL # BH18-084-097-49
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted
slightly, turn the appropriate screw, as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFF OR BRE
AK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM RECOMMENDED WEIGHT LOADS
HOLDS MOST 42” to 75” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.3 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
PLACE TV BEHIND THE STOPPER
1
2

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1) C- Bottom Panel (Qty. 1)
D- Left Side Panel (Qty. 1) E- Right Side Panel (Qty. 1) F- Lower Partition Panel (Qty. 1)
G- Left Door (Qty. 2) H- Right Door (Qty. 2) I- Adjustable Shelf (Qty. 2)
J- Upper Partition Panel (Qty. 1) K- Front Molding (Qty. 2) L- Top Front Stretcher (Qty. 1)
M- Bottom Front Stretcher (Qty. 1) N- Bottom Back Stretcher (Qty. 1) O- Bottom Side Stretcher
(with floor leveler) (with floor protector) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
P- Back Panel (Qty. 1) Q- Stop Rail (Qty. 1) R-
Cable Wheel (Qty. 2)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 42+2 extra) (Qty. 42+2 extra) (Qty. 43+2 extra)
(4) M4 x 50 mm Screw (5) M3.5 x 15 mm Washer Head Screw (6) Shelf Support
(Qty. 2+1 extra) (Qty. 36+1 extra) (Qty. 8+1 extra)
(7) Cam Lock Cover (8) 1/4" x 12 mm Bolt (9) Corner Connector (10) Rubber Bumper
(Qty. 24+1 extra) (Qty. 4+1 extra) (Qty. 2) (Qty. 8+1 extra)
(11) 1/4" x 19 mm Bolt Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 4+1 extra) (Qty. 1) (Qty. 1) (Included in plastic bag)
Tools required: Phillips screwdriver and rubber mallet (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and Bottom
Panel (C) and Fixed Shelf (B) using a Phillips screwdriver.
Cam Bolt
(20 used in this step)
②
B
C
A
2

7
Assembly Instructions
3. Securely screw the Cam Bolts (2) into the designated small holes on the Side Panels (D and E), the
Stretchers (L, M and N) and the Front Moldings (K).
Cam Bolt
(16 used in this step)
②
DE
L
M
N
K
K
2

8
Assembly Instructions
4. Glue two Wood Dowels (3) into the inner holes of the Lower Partition Panel (F) and attach it to the
Fixed Shelf (B) by engaging two Cam Locks (1) (Refer to page 3 on Cam Lock system operation
supplement).
B
F
1
3
Cam Lock
(2 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③

9
Assembly Instructions
5. Securely screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (B).
6. Attach the Upper Partition Panel (J) to the Fixed Shelf (B) with two Cam Locks (1) and two Wood
Dowels (3).
J
2
13
B
B
Cam Bolt
(2 used in this step)
②
Cam Lock
(2 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③

10
Assembly Instructions
7. Attach Side Panels (D and E) to the Fixed Shelf (B) with four Wood Dowels (3) and four Cam Locks
(1).
B
3
1
E
D
M8 x 30 mm Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①

11
Assembly Instructions
8. Attach one Front Molding (K) to each Side Panel (D and E) with two Wood Dowels (3) and two Cam
Locks (1).
B
E
D
K
K
K
1
3
M8 x 30 mm Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①

12
Assembly Instructions
9. Fasten two Corner Connectors (9) to the Top Panel (A) with two 12 mm Bolts (8).
A
9
8
1/4" x 12 mm Bolt
(2 used in this step)
⑧
Corner Connector
(2 used in this step)
⑨

13
Assembly Instructions
10. Attach the Top Front Stretcher (L) to the Top Panel (A) with one 30 mm Wood Dowel (3) and four Cam
Locks (1).
11. Insert two 12 mm Bolts (8) through the Corner Connectors (9) and screw into the Top Front Stretcher
(L).
M8 x 30 mm Wood Dowel
(1 used in this step)
③
Cam Lock
(4 used in this step)
①
A
L
8
3
1
1/4" x 12 mm Bolt
(2 used in this step)
⑧

14
Assembly Instructions
12. Glue ten Wood Dowels (3) into the inner holes on the vertical panels (D, E, J and K).
13. Position the Top Panel (A) onto the inserted Wood Dowels (3) and fasten it in place with six Cam Locks
(1).
M8 x 30 mm Wood Dowel
(10 used in this step)
③
Cam Lock
(6 used in this step)
①
A
L
E
D
J
K
K
1
3

15
Assembly Instructions
14. Combine the Bottom Front Stretcher (M), Back Stretcher (N) and Side Stretchers (O) together with four
Wood Dowels (3) and four Cam Locks (1).
1
3
N
M
O
O
M8 x 30 mm Wood Dowel
(4 used in this step)
③
Cam Lock
(4 used in this step)
①

16
Assembly Instructions
15. Attach the assembled base to the Bottom Panel (C) with the 30 mm Wood Dowels (3) and the Cam
Locks (1).
M8 x 30 mm Wood Dowel
(10 used in this step)
③
Cam Lock
(12 used in this step)
①
O
O
N
M
C
13

17
Assembly Instructions
16. Securely screw the Cam Bolts (2) into the designated small holes on the top of Bottom Panel (C).
Cam Bolt
(4 used in this step)
②
2
C

18
Assembly Instructions
17. Glue six Wood Dowels (3) into the inner holes on the vertical panels (D, E and F).
18. Position the Bottom Panel (C) onto the inserted Wood Dowels (3) and fasten it in place with four Cam
Locks (1) and two 50 mm Screws (4).
1
3
C
E
D
F
N
M
4
4
M8 x 30 mm Wood Dowel
(6 used in this step)
③
Cam Lock
(4 used in this step)
①
M4 x 50 mm Screw
(2 used in this step)
④

19
Assembly Instructions
19. Flip the assembly around at its front edges.
20. Now, go back and securely tighten all the Cam Locks and the Screws. Make sure that all the parts are
tight and there are no gaps between the parts. This will help keep the unit square.
21. Unfold and pick up the Back Panel (P) and align the pre-drilled holes with the threaded inserts on the
Fixed Shelf (B). Attach the Back Panel (P) in place using the provided Washer Head Screws (5).
5
E
P
P
5
M3.5 x 15 mm Washer Head Screw
(36 used in this step)
⑤

20
Assembly Instructions
22. Attach two Cable Wheels (R) to the backside of the unit with four 19 mm Bolts (11).
NOTE: You can use the Cable Wheels to help keep your entertainment center’s cables and cords
organized.
1/4" x 19 mm Bolt
(4 used in this step)
⑪
P
E
11
R